Epoch Design McKenzie 5115 User manual

McKenzie Loft Bed
5115: MK-TW-LB-NB
5118: MK-TW-LB-CO
Congratulations on the purchase of your McKenzie Twin Loft Bed. This bed has been crafted to the highest
standards of quality and safety and will give you many years of enjoyment and practical use. Your loft bed
can be used for sleeping and also for a highly space ecient work area under the bed.
Since this bed is a natural wood product, there will be variations in color and grain, and minor checking may
occur. This is normal and does not compromise the integrity of your bed. In fact, variation in character of
solid hardwood is integral to the beauty and appeal of hardwood furniture, and distinguishes it from
prefabricated, synthetic and composite materials.
Several basic safety considerations must be adhered to when using this bunk bed.
On this insert you will nd a list of the hardware and loft bed parts necessary for assembly, as well as
detailed instructions. Assembly is quite simple and requires only a at head screwdriver and a Phillips head
screwdriver. The use of a power drill with a clutch and a Phillips head attachment is helpful but not
necessary. Assembly will be most easily accomplished if you take the time to carefully sort the hardware and
familiarize yourself with the function of each piece.
If you should require assistance with assembly, part replacement or any other matter, contact the toll-free
Epoch Design Service Center from anywhere in the Continental United States, Monday through Friday,
9 AM – 5 PM Pacic Standard Time at 1-800-589-7990. You may also email your request or comments to
[e-mail] and a service representative will respond.
Thank you and Enjoy
HAVE QUESTIONS OR CONCERNS? CALL US FIRST: 1-800-589-7990
Copyright © 2018 Epoch Design™ All rights reserved
• Never allow a child under 6 years on a loft bed
• Always use the recommended size mattresses or mattress supports:
Standard twin 38"x 74" (96.5 cm x 188 cm) to help prevent the likelihood of entrapment or falls
• Ensure thickness of mattress does not exceed 9" (22.9 cm) for the upper bed
• Surface of mattress must be at least 5" (12.7 cm) below upper edge of safety rails
• Always use safety rails on both sides of upper bed
• Do not allow horseplay on or under bed(s) and prohibit jumping on the bed(s)
• Prohibit more than one person on the loft bed
• If the loft will be placed next to a wall, the safety rail that runs the full length of the bed should be placed
against the wall to prevent entrapment between the bed and the wall
• Follow the information on the warnings appearing on the loft bed end board and on the carton
• Do not remove warning label from bed
• Periodically check and ensure that the safety rails, ladder and other components are in their proper
positions, free from damage, and that all connectors are tight
• Do not use substitute parts
• Contact manufacturer or dealer for replacement parts
• The use of a water or sleep otation mattress is prohibited
• Keep these instructions for future reference
• Use of a night light may provide added safety precaution for a child using the upper bunk
•STRANGULATION HAZARD - Never attach or hang items to any parts of the bunk bed that are
not designed for use with the bed, including but not limited to hooks, belts or jump ropes
TO HELP PREVENT SERIOUS OR FATAL INJURY FROM ENTRAPMENT OR FALLS:
3-Aug-20181/6

Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
2x Printer/CPU brackets
Brackets to hold
accessory part S
4x bunk connector pins
Used to connect upper
bunk to lower unit
HARDWARE LIST
LOFT BED PARTS
ACCESSORIES
Groove
Lower shelf for
bookshelf tray
Computer/printer trayKeyboard tray
Wire basketWire le holder Wire Shelf
Upper shelf for
bookshelf tray
Alarm clock /
bookshelf tray
Pegboard backboardCork backboard
Upright support
for bookshelf
3xLadder steps
Connect with long
upright support
2x Short safety rails
Attach on front of bed
between long and short
upright supports
Extra holes for ladder
1x Head board
For upper loft
1x Foot board
For ladder side
of upperloft
1x Grooved upper side rail
Connects head boards on
wall side of upper loft
1x Upper side rail
Connects head boards
on the ladder side of loft
2x Long safety rails
For attachment to
upright support
on wall side of loft
2xUpright support
For attachment of
long safety rails to loft
2x Bottom end boards
For use on the lower
part of loft
1x Upper back rail
Connects end boards
on the lower unit
1x Lower back rail
Connects end boards
on the lower unit
1x Table top
With premounted
keyboard bracket
1x Long upright support
For front ladder and
front safety rail
1x Short upright support
Support for ladder
side safety rail
1x Slat bundle
Rests on side rails
(strap side down)
V
T
SRQP
O
N
M
L
K
JIHGF
E
D
C
B
A
22x 40mm bolts
Used to assemble long
safety rails, connect
safety rails to side rails
and assemble accessories
30x 30mm slat screw
Used to screw slats to rails
1x Hex key
Used to tighten
hardware
36x 110mm bolts
Used to connect head
boards and foot boards
to side rails
36x Barrel nuts
Used to secure
110mm bolts
9 x 50mm JC screws
Used to attach desktop
to bottom end board
U
W
mm 10 20 30 40 50 60 70 80 90 100 110
3-Aug-20182/6

Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
A
C
D
VII Groove
Slot
G
G
G
H
H
I
I
IV
V
E
E
F
E
E
F
F
Attach the two long safety rails Eto the unassembled
upright supports Fusing eight 40mm bolts.
Tighten with hex key (See Diagram III).
1
3
5
4
ledge side in
groove down
Groove
Slot
safety rail holes
Attach the assembly of Fand Esafety rails
to the rear side rail Cof the upper loft bunk
using four 40mm bolts (See Diagrams IV & V).
C
C
C
To assemble lower section of loft, attach bottom end
boards Gto back rails H&I.The upper back rail H
has a groove lengthwise along the top side of
the rail, and a slot along the face of the rail.
VI
Tighten the 110mm bolts with hex key.
Leave the bolts loose about 3 turns from
tight so the table top can be easily installed.
(See Diagram VI).
*Note: A power screwdriver with clutch
set to low comes in handy here.
2
To assemble the McKenzie loft bed arrange side rails C and
D(with pre-drilled safety rail holes on the side of each rail)
ledge side in, between headboard Aand footboard B. Rail C
should have it’s groove side down on the back wall side of
the loft bed. Insert the barrel nuts into the side rails. Insert
110mm bolts through the end boards and into the barrel nuts
(See Diagram I).
II
Unroll the slat bundle and lay it out strap side
down on the upper bunk. Using a Phillips head
screwdriver and 30mm slat screws, secure the
first slat on one end, then the final slat on
the other end making sure the slats
have been distributed evenly.
Then secure the remaining
slats to the rails.
I
B
C
III
F
E
Tighten the110mm bolts with
the hex key provided (Diagram II).
**NOTE: For left ladder configuration reverse headboard A& footboard B.
C
**Note: The two long safety rails have
sleeved, threaded inserts that anchor
the 40mm bolts and should face away
from the 40mm bolts.
Attach rails to end boards
with a total of eight 110mm
bolts and eight barrel nuts
(See Diagram VII).
3-Aug-20183/6

Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
VIII
IX
I
JG
Put the table top Jinto
the slot of the bottom
end boards and slide the
table edges back into
the slot on the back rail I
(See Diagram IX).
6
8
7
9
10
Push the bottom end boards
Using a Phillips head screw driver remove
the three round head screws holding the
front track guard on the underside of desk part J.
Set the track guard and three round head screws
aside to be re-installed in step #15.
apart about an extra two
inches in the front
(Diagram VIII).
*Note: The underside of the table has the pre-mounted
left side keyboard bracket.
Now fully tighten the eight 110mm bolts that attach
the end boards to the back rails.
*Note:There will be one extra hole on each end board.
With the table top seated in the slots of the
end boards, return the front legs of the
end boards to their original position.
Insert nine 50mm JC screws
through the end boards and
upper slotted back rail into the
edge of the desk and tighten
with the hex key.
J
UNDERSIDE
11
Notch
Locate the ladder upright support K, the short
upright support L and the two short safety rails M.
**NOTE: For left ladder conguration reverse parts L & K.**
Insert four barrel nuts
into each short safety rail
and four 110mm bolts
into each upright support.
Make sure the notches
on the upright supports
face the same direction.
Tighten with hex key.
*NOTE:
Left ladder
conguration
L
M
K
**NOTE:
Left ladder
conguration
ladder assembly
should appear
as shown.
Attach the ladder/safety rail assembly to
the loft using four 40mm bolts as shown.
Tighten with the hex key
(See Diagram XI).
XI
CONNECTOR
PIN
X
Place the loft bed assembly
on top of the lower unit.
Insert bunk connector pins
into each of the four corner
posts of the lower unit
(See Diagram x).
3-Aug-20184/6

Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
S
XVI
R
Locate the keyboard tray with attached bracket R.
Slide the bracket into the track which is mounted
on the underside of the desktop.
(See Diagram XV).
Push the pins flush to the backboard and insert it
into the grooved rails on the loft (See Diagram XIV).
PQ
12
15
16
13
14
Locate pegboard Q& corkboard P
make sure the spring
loaded pins are at the
top of each backboard.
XV
XIV
XII
XIII
O
17
Insert four 40mm bolts
through the bookshelf
upright support Uinto
the two shelves T& V.
Notice that the larger
bookshelf Vis located
on the bottom.
U
T
V
Tighten the bolts with
the hex key provided.
Hand tighten with
phillips head screwdriver.
(See Diagram XVI).
Retrieve the 3 round head
screws along with the
track guard from step #6
and re-attach it to the
bottom of the desk on the
front edge of the track.
Using a phillips head screwdriver
attach two 15mm screws to the
bottom of each printer
bracket as shown.
Insert four barrel nuts into each of
the three ladder steps O and secure
them to the loft with four 110mm bolts each as shown.
(See Diagram XII). Tighten the bolts with the hex key
provided (See Diagram XIII).
Attach the two printer/cpu
brackets to the printer/cpu tray S
using the two 40mm bolts.
Tighten with hex key.
3-Aug-20185/6

Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
19
18
Hang the alarm clock
shelf anywhere along
the top safety rails.
Hang your bookshelf
anywhere along the
headboard on either
end of the bed.
Hang the CPU shelf anywhere
along the bottom rails.
Starting with the largest
and working your way to the
smallest attach your three
wire organizers by tilting the
baskets and inserting the
prongs into the pegboard
holes, then bringing them
to a level position.
Congratulations, you are now ready to enjoy your loft bed.
3-Aug-20186/6