Epoch Design 5401 AM-QU-PB-BA User manual

Congratulations on the purchase of your Amore Platform Bed. This bed has been crafted to the highest
standards of quality and safety and will give you many years of enjoyment and practical use.
On this insert you will nd a list of the hardware and platform bed parts as well as detailed assembly
instructions. Assembly is quite simple and requires only a Phillips head screwdriver. The use of a power drill with
Phillips head attachment is helpful but not necessary. Assembly will be most easily accomplished if you take the time
to carefully sort the hardware and familiarize yourself with the function of each piece.
If you need assistance with assembly, part replacement or any other matter, please contact the toll-free Epoch
Design Customer Service Team from Monday through Friday, 9 AM-6 PM PST at 1 [phone]. You may also email
your request or comments to inf[email protected]om and a customer service representative will respond.
Thank you and Enjoy
EPOCH DESIGN , LLC AMORE PLATFORM BED
5401 AM-QU-PB-BA, 5400 AM-KI-PB-BA,
5405 AM-FU-PB-BA
6-Sept-20191/4
HARDWARE LIST
BED PARTS
HAVE QUESTIONS OR CONCERNS? CALL US FIRST: 1-800-589-7990
COPYRIGHT © 2019 EPOCH DESIGN™ ALL RIGHTS RESERVED
1x Allen Wrench
Used to tighten bolts
mm 10 20 30 40 50 60
16x 15mm Bolts
Used to attach
legs to bed
2x 60mm Bolts
Used to attach
center support
to drop foot
12x 15mm Machine Screws
Used to attach
brackets
55x 25mm Wood Screws
Used to attach
slat bundle to rails
2x Side Rails
Used to connect
end boards
A
1x Headboard
D
1x Center Support
F
1x Valance
I
1x Drop Foot
G
1x Slat Bundle
rest on side rails and
supports mattress
(strap side down)
H
1x Headrail
B
1x Footboard
C
E
4x Legs
2x Brackets
Used to attach
center support rail

Carefully place both side rails (A),
headrail (B) and footboard (C) on a clean soft
surface. Once in the correct position, gently
slide the bamboo tenon on headrail (B)
into the mortise slot on side rail (A).
(Diagram I)
Repeat this step with the opposite side rail (A).
After both side rails have been axed to headrail (B)
slide the bamboo tenon biscuits on footboard (C)
into the mortise slots on side rail (A).
(Diagram II)
6-Sept-20192/4
HAVE QUESTIONS OR CONCERNS? CALL US FIRST: 1-800-589-7990
COPYRIGHT © 2019 EPOCH DESIGN™ ALL RIGHTS RESERVED
1
Carefully tilt the bed frame upward by
raising the footboard end (C) and insert the
two legs (E) into the notched alcoves in the
footboard (C) and the side rails (A).
Loosely attach the legs (E) to the bed frame
by inserting two 15mm bolts through the
raised bracket arms on the legs on the inside
of the bed frame and nger tighten.
(Diagram IV)
Then insert two 15mm bolts through the
bottom of the leg brackets and into the
footboard (C) and the side rails (A) and
nger tighten. (Diagram IV)
3
Gently and evenly slide all four bamboo tenons
on headboard (D)into the mortise slots on the top
side of the side rails (A). (Diagram III)
*NOTE: It may be necessary to tap on the top of the headboard uprights
with a rubber hammer to fully seat the headboard into the rails.
2
A
C
B
I
II
III
D
AA
D
A
C
B
E
E
D
C
C
A
C
E
IV
A
tenon
tenon
tenon

6-Sept-20193/4
HAVE QUESTIONS OR CONCERNS? CALL US FIRST: 1-800-589-7990
COPYRIGHT © 2019 EPOCH DESIGN™ ALL RIGHTS RESERVED
Using the 12 machine screws provided,
attach the two steel center support brackets
(open end up) to the foot and head board.
5
Attach the drop support to the center
support by placing center support (F) into
the slot on the top of the drop foot (G).
Then insert two 60mm bolts into the
non-threaded side of the drop foot (G),
through the center support (F) and into
the threaded inserts. Tighten with the
Allen wrench provided. (Diagram VII)
*NOTE: To achieve tight corner joints, it may be necessary to pull
the corner joints together while tightening the leg bolts.
6
Lift the bed frame from the headboard end (D)
and insert the two legs (E) into the notched
alcoves in the headrail (B) and the side rails (A).
Loosely attach the legs (E) to the bed frame
by inserting two 15mm bolts through the
raised bracket arms on the legs on the inside
of the bed frame and nger tighten.
(Diagram V)
Then insert two 15mm bolts through the
bottom of the leg brackets and into the headrail
(B) and the side rails (A) and nger tighten.
(Diagram V)
4
Place the completed center support assembly
into the center support brackets, then tighten all
of the leg bolts with the Allen wrench provided.
4
EE
B
B
D
A
A
A
V
E
VI
F
F
G
G
VII
F
G

3
4
1
2
6-Sept-20194/4
HAVE QUESTIONS OR CONCERNS? CALL US FIRST: 1-800-589-7990
COPYRIGHT © 2019 EPOCH DESIGN™ ALL RIGHTS RESERVED
Congratulations, you have now completed the assembly
of your Amore Platform Bed!
Simply place your favorite mattress on the slat rails and
you are free to enjoy Epoch Design’s traditional
craftsmanship, quality bamboo construction and
sustainable natural beauty for generations
to come.
Unroll the slat bundle (H) strap side down
on the side rail ledges (A).
Make sure all of the slats are distributed evenly
across the length of the bed, then attach the
end slats closest to the footboard to the side
rail ledges using the 25mm wood screws and
a Phillips head screwdriver or power drill
with the clutch set to low.
Then attach the end slats closest to
the headboard before continuing
on to secure the remaining
middle slats.
7
Attach the valance (I) to the front of the bed
using seven 25mm wood screws with a Phillips
head screwdriver or power drill with the clutch set
to low.
8
H
3
4
A
I