Epoch Design Pacifica User manual

Congratulations on the purchase of your Pacica Platform Bed. This bed has been crafted to the highest
standards of quality and safety and will give you many years of enjoyment and practical use.
On this insert you will nd a list of the hardware and platform bed parts as well as detailed assembly instructions.
Assembly is quite simple and requires only a at head screwdriver and a Phillips head screwdriver. The use of a power
drill with Phillips head attachment is helpful but not necessary. Assembly will be most easily accomplished if you take
the time to carefully sort the hardware and familiarize yourself with the function of each piece.
If you need assistance with assembly, part replacement or any other matter, please contact the toll-free Epoch
Design Customer Service Team from Monday through Friday, 9 AM-5 PM PST at 1 [phone]. You may also email
your request or comments to inf[email protected]om and a customer service representative will respond.
Thank you and Enjoy
EPOCH DESIGN , LLC
Pacifica / Modeno
5472: PM-QU-PB-ES 5474: PM-TW-PB-ES 5479: PM-QU-PB-GR
5476: PM-FU-PB-ES 5477: PM-KI-PB-ES 5478: PM-KI-PB-GR
5475: PM-FU-PB-GR
1/2
HARDWARE LIST
30 mm slat screws
Used to secure
slats to rails
24x TWIN 39x QUEEN
36x FULL 52x KING
1x Hex key
Used to tighten
bolt hardware
1x Slat bundle
Rest on side rails and supports
mattress (strap side down)
Drop supports
Used to attach center support
0x TWIN 2x QUEEN
1x FULL 4x KING
2x Side rails
Connect end boards
1x Headboard
1x Footboard
2x Center supports
Used to attach
drop support
KING
1x Headboard
1x Footboard
1x Center support
Used to attach
drop support
FULL / QUEEN
1x Headboard
1x Footboard
TWIN
BED PARTS
HAVE QUESTIONS OR CONCERNS? CALL US FIRST: 1-800-589-7990
Copyright 2020 Epoch Design™ All rights reserved
mm 10 20 30 40 50 60 70
24-July-2020
50 mm screws
Used to secure
center support
0x TWIN 2x QUEEN
2x FULL 4x KING
8x 20 mm bolts
To connect side
rails to Headboard
& Footboard
8x Flat Washers
To connect side
rails to Headboard
& Footboard
8x Lock Washers
To connect side
rails to Headboard
& Footboard

TWIN KING
KING
FULL
QUEEN
FULL / QUEEN / KING
KING
Unroll the slat bundle strap side down onto the
side rails distributing them evenly from end to end.
Starting with the rst slat, and last slat, secure the slats
to the side ledges with 30 mm slat screws using a Phillips
head screwdriver. A power screwdriver with clutch set on
low is useful here.
Place the center support into the wooden
center support brackets in the headboard and
footboard. Insert the center support to the
bottom of the brackets. Drive one 50mm wood
screw through the hole on the top side of
center support beam with a Phillips Head
screwdriver. Then drive another 50mm wood
screw through the hole on the top side
of center support beam on the footboard
end of the center support.
Attach the drop support to the center support
by inserting the threaded stud on top of the
drop support into the threaded hole in the
bottom of the center support beam.
Rotate the drop support to screw the
drop support into place.
If you have the TWIN size bed, skip Step (2) & (3) and go to Step (4).
Make sure the slat rail ledge is facing the inside of the bed then install a lock washer and a at washer
onto two of the 20 mm bolts, and thread them into the pre-drilled holes in the headboard. Slide the
hooks installed on the slide rail between the headboard and the at washer and loosely nger tighten (A).
Next, repeat the process with
the other end of the rails into
the footboard (B).
C
TWIN
1
2
3
4
Have a question? Need a part ASAP? Call 1-800-589-7990 or email [e-mail].
24-July-20202/2
A
B
FULL / QUEEN
FULL / QUEEN
FULL / QUEEN