Epoch Design Radia 5119 User manual

Radia Twin Size Loft Bed
5119: RA-TW-LB-NB
Congratulations on the purchase of your Radia Loft Bed. This bed has been crafted to the highest standards
of quality and safety and will give you many years of enjoyment and practical use. Your loft bed can be used
for sleeping and also for a highly space ecient work area under the bed.
Since this bed is a natural wood product, there will be variations in color and grain, and minor checking may
occur. This is normal and does not compromise the integrity of your bed. In fact, variation in character of
solid hardwood is integral to the beauty and appeal of hardwood furniture, and distinguishes it from
prefabricated, synthetic and composite materials.
Several basic safety considerations must be adhered to when using this bunk bed.
On this insert you will nd a list of the hardware and loft bed parts necessary for assembly, as well as
detailed instructions. Assembly is quite simple and requires only a at head screwdriver and a Phillips head
screwdriver. The use of a power drill with the clutch set on low and a Phillips head attachment is helpful but
not necessary. Assembly will be most easily accomplished if you take the time to carefully sort the hardware
and familiarize yourself with the function of each piece.
If you should require assistance with assembly, part replacement or any other matter, contact the toll-free
Epoch Design Service Center from anywhere in the Continental United States, Monday through Friday,
9 AM – 5 PM Pacic Standard Time at 1-800-589-7990. You may also email your request or comments to
[e-mail] and a service representative will respond.
Thank you and Enjoy
HAVE QUESTIONS OR CONCERNS? CALL US FIRST: 1-800-589-7990
Copyright © 2018 Epoch Design™ All rights reserved
• Never allow a child under 6 years on a loft bed
• Always use the recommended size mattresses or mattress supports:
Standard twin 38"x 74" (96.5 cm x 188 cm) to help prevent the likelihood of entrapment or falls
• Ensure thickness of mattress does not exceed 9" (22.9 cm) for the upper bed
• Surface of mattress must be at least 5" (12.7 cm) below upper edge of safety rails
• Always use safety rails on both sides of upper bed
• Do not allow horseplay on or under bed(s) and prohibit jumping on the bed(s)
• Prohibit more than one person on the loft bed
• If the loft will be placed next to a wall, the safety rail that runs the full length of the bed should be placed
against the wall to prevent entrapment between the bed and the wall
• Follow the information on the warnings appearing on the loft bed end board and on the carton
• Do not remove warning label from bed
• Periodically check and ensure that the safety rails, ladder and other components are in their proper
positions, free from damage, and that all connectors are tight
• Do not use substitute parts
• Contact manufacturer or dealer for replacement parts
• The use of a water or sleep otation mattress is prohibited
• Keep these instructions for future reference
• Use of a night light may provide added safety precaution for a child using the upper bunk
•STRANGULATION HAZARD - Never attach or hang items to any parts of the bunk bed that are
not designed for use with the bed, including but not limited to hooks, belts or jump ropes
TO HELP PREVENT SERIOUS OR FATAL INJURY FROM ENTRAPMENT OR FALLS:
2-Aug-20182/5

2x 15mm at head screw
used to secure “L bracket”
2x Printer/CPU brackets
Brackets for accesories part R
1x L bracket
Used to secure desk
to ladder
3x Cam lock connectors
Used to secure desktop
3x Cam locks
Used to lock cam lock
connectors into place
HARDWARE LIST
1x Headboard
For upper loft 1x Foot board
For ladder side
of upper loft
1x Grooved upper side rail
Connects headbords on
back wall side of upper loft
1x Upper side rail
Connects headbords
on upper loft
2x Long safety rails
For attachment to upright
support on wall side of loft
GROOVE
GROOVE
SLOT
2x Upright supports
For attachment of
long safety rails to loft
1x Upper back rail
Connects endboards
on lower unit.
1x Lower back rail
Connects endboards
on lower unit.
Desk
Desk
For lower unit
1x Slat bundle
Rests on upper
side rail strap
side down
1x Long upright support
For front ladder and front
safety rail
1x Short upright support
Support for ladder side
of safety rail
2x Short safety rail
Attach on front of bed
between short upright
and long upright on
ladder side of bed
3x Ladder steps
used to
assemble ladder
1x Corkboard 1x Pegboard 1x Computer printer tray 1x Alarm clock book shelf
1x Wire le holder 1x Wire shelf 1x Wire basket
Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
LOFT BED PARTS
ACCESSORIES
4x Connector pins
Used to connect upper
bunk to lower unit
18x 40mm bolts
Used to assemble long
safety rails and connect
safety rails to side rails
30x 30mm slat screws
Used to screw slats to rails
1x Hex key
Used to tighten
hardware
36x 110mm bolts
Used to connect head
boards and foot boards
to side rails
36x Barrel nuts
Used to secure
110mm bolts
9 x 50mm JC screws
Used to attach desktop
to bottom end board
EXTRA HOLES
FOR LADDER
2x Bottom end boards
For use on lower part
of loft
2-Aug-20182/5
mm 10 20 30 40 50 60 70 80 90 100 110

Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
To assemble The Radia loft bed, arrange
side rails C and D with the ledge side in
between headboard Aand footboard B.
Rail C should have it’s groove side down
on the back wall side of the loft bed.
Insert barrel nuts into the holes in side
rails C and D (See diagram I) and rotate
the barrel nut screw slots so they are
parallel with the ground.
I
Insert 110 mm bolts through end boards and into the barrel nuts .
*foot-board has extra holes for ladder attachment on right side of loft.
Tighten 110 mm bolts with hex key provided (See diagram II).
Holes for ladder
Ledge
Groove
3
5
2
III
Place the two safety rails Ethreaded inserts out in the slots
in the unassembled upright supports F. Attach Fto Eusing
eight 40mm bolts and tighten with hex key (See diagram III).
**NOTE: The head of the threaded inserts
face away from the 40 mm bolts as shown.
The long rail will be on the side
of the loft which is opposite
the ladder and nearest the wall.
Attach the upright supports Fand long safety rails Eto the
rear side rail Cof the upper loft bunk using four 40 mm bolts
(See diagram IV and V).
V
IV
4
VI
The lower back rail Ihas two
holes on each end of the rail.
Attach rails to end boards with
eight 110mm bolts and eight
barrel nuts (See diagram VI).
To assemble the lower section of the loft, attach
bottom end boards Gto back rails Hand I. The upper back rail Hhas a groove
lengthwise along the top and a slot
lengthwise on the face of the rail.
Groove
Slot
**NOTE: A power screwdriver with clutch
set to low comes in handy here.
Unroll the slat bundle and lay it out
strap side down on the upper bunk.
Using a Phillips head screwdriver and
30mm slat screws secure the rst slat
on one end, then the nal slat on the
other end making sure the slats have
been distributed evenly. Then secure
the remaining slats to the rails.
II
Tighten the bolts with the hex key
leaving them about 3 turns from tight so
the desktop can be more easily installed.
Then push the outside legs of the end
boards outward about two inches.
(See diagram VII).
VII
2-Aug-20183/5

Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
6
8
10
12
11
9
Attach the ladder/safety rail assembly to the loft using
four 40 mm bolts as shown.
Tighten with hex key
(See diagram XV).
VIII
Insert three camlock connectors into
the corresponding threaded inserts in
the large part of the desk top K.
Tighten with a screwdriver (See Diagram VIII).
Slide the camlock connectors into the corresponding holes on
the edge of piece J hole side facing up.
To assemble the desk top, lay down desk
top Kon a soft, clean surface face down. 7
IX
Insert three camlocks into the three
holes on the horizontal surface of piece J.
Tighten camlocks about a half turn or until
the two desk pieces are joined snugly
(See diagram IX).
Put the desk top assembly J& K into the slot of the bottom
end boards and slide the edges back into the slot on the
back rail H.
XII
With the desk top seated in the
slots of the end boards, return
the front legs of the end boards
to their original position.
XVI
Locate the three ladder
steps O. Insert four barrel
nuts for each step
(diagram
XVI ).
Insert four 110 mm bolts for each step, position
them as shown and tighten with hex key provided.
13
With the assistance of a
friend place the loft bed
assembly on top of the
lower unit.
Insert one bunk connector pin
into each corner post of
the lower unit.
Insert nine 50mm JC screws through
the end boards, the upper slotted
back rail and into the desk. Tighten with
a hex key provided. Now fully tighten eight 110mm bolts
that attach the end boards to the back rail (See diagram XII).
Make sure the notches on uprights
L & M are facing the same direction.
Insert eight barrel nuts into the
short safety rails N and eight 110mm
bolts into the upright supports L & M.
Tighten bolts with the hex key.
(See diagram XIV).
Locate the long upright support L, the short upright support M
and the two short safety rails N.
XIV
XV
2-Aug-20184/5

Next use a Phillips head screwdriver to sink two 30 mm wood
screws through the bracket and into the bottom of the tray R.
Have a question? Need a part ASAP? Please call 1-800-589-7990 (Monday through Friday 9am to 5pm PST).
Hang the alarm clock
tray S anywhere along
the top side rails.
Hang the printer/CPU
tray R anywhere along
the bottom rails.
**NOTE: To reposition trays remove
trays completely and
gently reposition to avoid
scratching nish.
Attach the three wire organizer baskets T, U, V, to the pegboard as desired by
tilting the basket and inserting the prongs into the holes and push the basket back
down to a level position to secure the basket to the pegboard (See diagram XIX).
Install the Lbracket in the predrilled holes underneath the desk
and behind the ladder/safety rail assembly using two 15 mm
wood screws and a Phillips head screwdriver (See diagram XVII).
XVIII
XVII
XIX
Locate the corkboard Pand pegboard Q.
Make sure the spring loaded pins are at
the top of each backboard. Push the pins
ush to the backboard and insert the
backboard into the grooved rails on the
loft (See diagram XVIII).
17
14
Attach the two printer/CPU
brackets to the tray Rusing two
40 mm bolts that go through the
back of the tray. Tighten with the
hex key provided.
2-Aug-20185/5