Epoch Design Gabriel 5140 User manual

Gabriel Trundle Bed • Model #5140
Congratulations on the purchase of your Gabriel Trundle Bed. This bed has been crafted to the
highest standards of quality and safety and will give you many years of enjoyment and practical
use. Your hardwood trundle bed can be used as two individual sleeping beds or when the need
arises the bottom bed can be changed into a storage drawer with the dividers provided.
Since this bed is a natural wood product there will be variations in color and grain, and minor
checking may occur. This is normal and does not compromise the integrity of your bed. In fact,
variation in character of wood is integral to the beauty and appeal of hardwood furniture, and
distinguishes it from prefabricated, synthetic or composite materials.
On this insert you will find a list of hardware and trundle bed parts necessary for assembly, as
well as detailed instructions. Assembly is quite simple and requires only a flat head screwdriver
and a Phillips head screwdriver. The use of a power drill with Phillips head attachment is helpful
but not necessary. Assembly will be most easily accomplished if you take the time to carefully
sort the hardware and familiarize yourself with the function of each piece.
If you need assistance with assembly, part replacement or any other matter, contact the toll-free
Epoch Design Service Center from anywhere in the Continental United States, Monday through
Friday, 9AM - 5PM PST at 1-800-589-7990. You may also fax your request or comments to
425-284-0885 or email info@epochbydesign and a service representative will respond.
Thank you and enjoy!
EPOCH DESIGN, LLC

A
1) Attach footboard and headboard to side rails. Insert barrel
nuts into side rails. Insert 100mm bolts through end boards
and into barrel nuts (A).
B
2) Tighten 100mm bolts
with hex key provided
(B).
3) Attach the two bottom bed end panels to the front and
back panels. Use the 60 mm bolts and barrel nuts as
shown in diagram (C).
C
4) Use the hex key to tighten each of the eight 60mm
bolts (D). Then use a Phillips Head screwdriver to
attach the trundle handles to the front panel using six
35mm small bolts (E).
D
E
5) Attach the two plank braces to bottom bed as shown
above. The braces should lay flush with the
surrounding ledge.
F
6) Insert the eight large wood screws into the plank
braces. Fasten the screws using a Phillips Head
screwdriver (F).
Have a question? Need a part ASAP? Call 1-800-589-7990

Have a question? Need a part ASAP? Call 1-800-589-7990
12) To use the bottom bed as a storage drawer, simply
remove the mattress and insert the four wire retainers
as shown above. Slide the drawer partitions into the
wire retainers down the grooves on the partitions.
11) Roll the lower bed under the upper bed. Now use the hex
key to re-tighten all bolts so that the bed assembly is
rigid. It may be necessary to re-tighten bolts after wood
has acclimated to your weather region. You are now
ready to enjoy your trundle bed.
10) Unroll the slat bundle (strap side down) and
spread out from end to end of bed. Now attach
each slat to the side rail with the 32 slat screws
provided (H).
9)Now flip the lower bed back over and lay the three
bottom planks into the bed. The top side of the planks
will have countersunk holes for the screws. Insert and
tighten the eight screws on each plank.
G
8) Attach casters to bottom of bed using two screws
for each caster (G). Notice the casters are located
on the inside of each rail.
7) On a soft surface (carpet or cardboard box) carefully flip
over the bottom bed.

8
8
16
6
58
8
1
Hardware List
Trundle Bed Parts
1
1
2
quantity
Shorter footboard for use at foot of bed
Taller head board for use at head of bed
100 mm bolt Connects headboard & footboard
to side rails
Attaches bottom bed front, back and end panels
60 mm bolt
Attaches trundle handles to bottom front panel
35 mm small bolt
barrel nut Secures bolts
Secures slats to rail and bottom planks to braces
Attaches plank brace to lower bed frame
Used to tighten bolt hardware
Hex key
1 1/4”Plank brace screw
1”slat screw
1
3
2
Bottom planks to support mattress in rollaway bed
Slat bundle which rests on side rails, strap side down, and supports mattress
Side rails to connect headboard to footboard
Drawer dividers used to make optional drawer space in bottom bed
Trundle handles
12 Attaches caster wheels to bottom of bed
1”Caster wheel screw
6
4Wire retainer
Caster Wheel
Used to convert lower bed into storage
Attaches to bottom bed to enable roll away feature
Plank support braces
2
3
2
1
1Bottom bed back panel
Bottom bed front panel
Bottom bed end panels
Have a question? Need a part ASAP? Call 1-800-589-7990