Epson C32C824151 - UB E02 Print Server Use and care manual

UB-E02
Technical Reference
Guide
10Base-T/100Base-TX
Ethernet Interface board
EPSON English
404999000

Rev. A i
UB-E02 Technical Reference Guide
CAUTIONS
❏This document shall apply only to the product(s) identified herein.
❏No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of
Seiko Epson Corporation.
❏The contents of this document are subject to change without notice. Please contact us for the latest information.
❏While every precaution has been taken in the preparation of this document, Seiko Epson Corporation assumes no
responsibility for errors or omissions.
❏Neither is any liability assumed for damages resulting from the use of the information contained herein.
❏Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties
for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or
abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.)
failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
❏Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options
or any consumable products other than those designated as Original EPSON Products or EPSON Approved
Products by Seiko Epson Corporation.
TRADEMARKS
EPSON®and ESC/POS®are registered trademarks of Seiko Epson Corporation.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
General Notice: Other product and company names used herein are for identification purposes only and may be
trademarks of their respective companies.

ii Rev. A
Revision Information
Revision Page Altered Items and Contents
Rev. A

Rev. A iii
UB-E02 Technical Reference Guide
About This Guide
This guide is intended to provide all information necessary for system planning, design,
installation and application of the UB-E02 for designers and developers of POS systems.
Contents of the Guide
The configuration of the guide is as follows:
Related Documents
Chapter 1, “System Preparation” Supported operating system, network
protocols, TM printers, and other limitations.
Chapter 2, “Installation” Gives information on how to install and use the
UB-E02.
Chapter 3, “Utilities” Gives information on how to use the utilities.
Chapter 4, “Programming Samples” Includes practical programming information.
Chapter 5, “Specification” Gives specifications.
Appendix A, “Definitions” Provides definitions of terms used in this guide.
Software/document name Description
UB-E02 User’s Manual Provides instructions for operators of POS systems in which the
UB-E02 is installed so that the operators can use the UB-E02 safely
and correctly.

iv Rev. A
EMC and Safety Standards Applied
Product Name: UB-E02
Model Name: M155B
The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the EPSON
PS-170 power supply and TM series printers.)
Europe: CE marking
North America: EMI: FCC/ICES-003 Class A
Japan: EMC: VCCI Class A
Oceania: EMC: AS/NZS 3548, CISPR22 Class B
WARNING
The connection of a non-shielded interface cable to this board will invalidate the EMC standards of this device.
You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your
authority to operate the equipment.
CE Marking
The board conforms to the following Directives and Norms:
Directive 89/336/EEC EN 55022 Class B
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-11
The printer in which this board is installed does not conform to the following:
Directive 90/384/EEC EN45501
FCC Compliance Statement
For American Users
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
For Canadian Users
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Rev. A v
UB-E02 Technical Reference Guide
CAUTION:
Connecting an outdoor overhead LAN cable directly to your product
Connecting an outdoor overhead LAN cable directly to your product may lead to
lightning damage. If you need to connect such a cable to your product, the cable must
be protected against an electrical surge between the cable and your product. You
should avoid connecting your product to a non-surge protected outdoor overhead LAN
cable.
GEREÄUSCHPEGEL
Gemäß der Dritten Verordnung zum Gerätesicherheitsgesetz (Maschinenlärminformations- Verordnung-3. GSGV) ist
der arbeitsplatzbezogene Geräusch-Emissionswert kleiner als 70 dB(A) (basierend auf ISO 7779).
Key to Symbols
The following symbols are used in the documentation for this product. See the specific warnings
and cautions at appropriate points throughout this guide.
WARNING:
Warnings must be followed carefully to avoid serious bodily injury.
CAUTION:
Cautions must be observed to avoid minor injury to yourself, damage to your
equipment, or loss of data.
Note:
Notes have important information and useful tips on the operation of the product.

vi Rev. A
Safety Precautions
This section presents important information to ensure safe and effective use of this product.
Please read this section carefully and store it in an accessible location.
CAUTION:
❏ Be careful to avoid dropping conductive objects such as paper clips on the circuit
board, as they could short circuit connections and cause damage from excessive
current.
❏ This product should only be connected to the devices specified in this guide.
Connecting other devices could cause damage, fire or explosion.
❏ Never disassemble or modify this product. Tampering with this product may result in
injury, fire, or electric shock.
❏ Be sure to set the product on a firm, stable, horizontal surface. The product may
break or cause injury if it falls.
❏ Never connect a public telephone line to the modular connector on this product.
❏ Do not use in locations subject to high temperature, humidity or dust levels.
Excessive temperature, humidity or dust may cause equipment damage, fire, or
shock.
❏ Parts on the circuit board may become hot during operation. Therefore, wait
approximately 10 minutes after turning the power off before touching them.
❏ To prevent the possibility of electrical shock, do not perform installation or connect
cables during a thunderstorm.
Label
A caution label like the one is attached near the display module connector of the TM printers.
The label has the following meaning:
“The display module connector and the drawer kick-out connector use the same type of
Ethernet connector; therefore, be sure not to connect the Ethernet connector cable or the
telephone line to the display module connector or the drawer kick-out connector.”
Product Servicing
This product cannot be serviced at the component level. If damage occurs, the UB-E02 should be
replaced as a unit.

Rev. A vii
UB-E02 Technical Reference Guide
Introduction
The UB-E02 is the 10Base-T/100Base-TX Ethernet interface board designed for the EPSON®TM
printers. The board lets you connect your EPSON printer directly to your network and use it as a
kitchen printer.
Operating Environments
Supported Operating Systems
❏Microsoft®Windows®95, Windows®98 Second Edition, Windows®2000 Professional,
and Windows®XP Professional
❏Windows NT®4.0
Supported Protocols
❏TCP/IP
Environments for Setup Utility
❏EPSON TMNet WinConfig applies to the following versions of Windows:
•Windows95
• Windows 98 Second Edition
• Windows 2000 Professional
• Windows XP Professional
•WindowsNT4.0
❏EPSON TMNet WebConfig is recommended to be used with the following internet browser:
• Microsoft Internet Explorer version 5.0 or later

viii Rev. A
Supported TM Printers
The following printers can use the UB-E02.
(The TM-J8000, TM-T285, and RP-U420 cannot use the UB-E02.
For new models, please ask your dealer.)
❏TM-U200 Series
❏TM-U210 Series
❏TM-U230
❏TM-U325
❏TM-U590
❏TM-U675
❏TM-T88/T88II/T88III
❏TM-T90
❏TM-H5000/H5000II
❏TM-H6000/H6000II
❏TM-J2000/J2100
❏TM-J7000/J7100
❏TM-J7500/J7600
❏TM-L90