Equalizer TRANSFORMER TFM50 User manual

www.equalizer.com
[e-mail] 512.388.7715
• Remove all trim panels surrounding the work area and
identify any clips/setting pins. Make sure to use proper vehicle
and personal protection.
• Insert cord on the spindle on one side of the Transformer®,
lace cord around perimeter of the quarter glass on the
outside. Anchor using Equalizer® Large or Mini anchor cup
(sold seperately) to the vehicle.
• Attach the SideStriker™ to the door striker, insert
Transformer® to the SideStriker™ and secure with locking pin.
• Apply tape on the glass and body as well so that when the
last cut is made, the glass will stay in place.
• Using either the ratchet (included) or your drill with provided
drill bit, begin cutting until your cut-out is complete.
• When you encounter the clips, make sure that the wire/cord
stays between the clip and the body of the vehicle.
• As you begin cutting again, keep in mind that the glass is now
loose, so slow and easy movements are required. If not, you
could pop the glass out too soon causing damage to the glass
and or body of the vehicle. Continue cutting until wire/cord
crosses making the final cut.
®
USER GUIDE
USEFUL TIPS
INSTRUCTIONS
• Be mindful of the cord or wire crossing or
twisting during setup. (see instructional video)
• When using wire, be conscious of possible
spring-back when wire gets unspooled.
• When using your drill of choice, we
recommend a low speed setting for a smooth
cut. Using a higher speed may cause the cord
to break or wire to snap.
*DO NOT USE IMPACT TOOLS WITH YOUR
TRANSFORMER®*
TFM50 Includes:
Transformer® Quarter Glass Removal Tool
PRM338 -Ratchet
TSD192 - Drill Bit
SDS192 - SideStriker™
I-SDS-FP - Protection Pad
GSS220 - Guide Sheets
RC100 - RipCordHD™
SFR350 - SwitCutPro® 350
QUARTER GLASS REMOVAL WITH SIDESTRIKER™
Scan for Instructional Video

www.equalizer.com
[e-mail] 512.388.7715
Equalizer® warrants this product is free from
defects in materials and workmanship when
used for the purpose intended, under normal
conditions, and provided it receives the
proper care and maintenance as described in
the User Guide section. This warranty is good
only for authentic, original, legitimate tools
manufactured by Equalizer® and sold through
Authorized Distributors or from Equalizer®
directly. These terms cover the following items
for one year from purchase date: locking pins,
spindles, anchor mechanism.
Equalizer® will repair or replace, at our
discretion, any defective part. Our goal is for
tools to be repaired and sent back the same
day they are received.
Equalizer® reserves the right to refuse repair,
at our expense, any tool which has not been
properly maintained as specified in the User
Guide and Warranty Section.
To send in your tool for repair, contact
Equalizer® to receive a RMA number. If you
have any questions about your tool call us at
512.388.7715, or email [e-mail].
Please send the entire tool to:
Equalizer®
Attention: Repair Department/ RMA# ______
2611 Oakmont Drive Round Rock, TX 78665 USA
• Warranty does not apply to abuse, misuse,
normal wear and tear, or to accessories.
• Damage caused where repairs have been
made or attempted by unauthorized persons.
• Using wire and/or cord other than the
Authorized and recommended Equalizer® wire
and/or cord will automatically void warranty.
• Using IMPACT Tools will automatically void
warranty.
Equalizer® Transformer® is warrantied for ONE
year to be free of factory defects from the date
of purchase.
®
WARRANTY
INFORMATION
WARRANTY TERM
WHAT IS COVERED?
WHAT IS NOT COVERED?
WARRANTY CLAIMS
Scan to Request an RMA
for Tool Repair