Sauder Anda Norr 427707 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
Enlish p 1-28
Français p 29-32
Español p 33-36
Lot # 555162 11/05/20
Purchased: __________________
L-Shaped Desk
Anda Norr Collection | Model 427707
For all your
newfanled gadgetry.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5
6-28
29-32
33-36
37-38
39
Pae 2 www.sauder.com/service 427707

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LARGE TOP (1)
B SMALL TOP (1)
C LEFT END (1)
D LEFT FRAME (1)
E REAR FRAME (1)
F LONG BACK (1)
G SHORT BACK (1)
H LONG BRACE (1)
J SHORT BRACE (1)
K UPRIGHT (1)
L RIGHT END (1)
M SHELF (1)
N SMALL BACK (1)
O BOTTOM (1)
P FRONT LEG (1)
Q REAR LEG (1)
R BRACE (2)
S SMALL DRAWER FRONT (1)
T SMALL LEFT DRAWER SIDE (1)
U SMALL RIGHT DRAWER SIDE (1)
V SMALL DRAWER BACK (1)
W DRAWER BOTTOM (2)
X LARGE DRAWER FRONT (1)
Y LARGE RIGHT DRAWER SIDE (1)
Z LARGE LEFT DRAWER SIDE (1)
AA LARGE DRAWER BACK (1)
A
B
C
D
E
FG
H
J
KL
M
N
O
P
Q
R
R
S
T
U
V
W
W
XY
Z
AA
Pae 3www.sauder.com/service427707

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
ANGLED HEAD
CAM SCREW - 27
5
Anled head
STRAIGHT HEAD
CAM SCREW - 8
6
Straiht head
WOOD DOWEL - 25
7APPLIQUE CARD - 3
8
GROMMET
WITH CAP- 2
9 10 GROMMET - 1 12 FILE
GLIDE - 2
CONNECTOR
PLATE - 1
13
PULL - 2
11
1/2" PAN HEAD SCREW - 24
20
1-1/2" FLAT HEAD SCREW - 14
14 1-3/8" WAFER HEAD SCREW - 4
15
9/16" PAN HEAD SCREW - 4
18 19 12" MACHINE SCREW  16
9/16" WAFER HEAD SCREW - 8
1716 138" MACHINE SCREW  8
(EXTENSION SET SHOWN SEPARATED)
LARGE HIDDEN
CAM - 27
3SMALL HIDDEN
CAM - 8
4
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4
Pae 4 www.sauder.com/service 427707

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Pae 5www.sauder.com/service427707

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push thirteen LARGE HIDDEN CAMS (3) into the LEFT
END (C), LONG BACK (F) and SHORT BACK (G).
å Turn four ANGLED HEAD CAM SCREWS (5) into the
LEFT END (C) and SHORT BACK (G).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
F
C
G
1
Arrow
3
3
Arrow
Arrow
3
5
Pae 6 www.sauder.com/service 427707

å Insert seven WOOD DOWELS (7) into the BACKS (F and G).
Step 2
F
G
7
7
7
7
Pae 7www.sauder.com/service427707

å Fasten the LEFT END (C) and SHORT BACK (G) to the
LONG BACK (F). Tihten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LONG BACK
insert into the LEFT END and SHORT BACK.
Step 3
F
C
G
1
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Surface without holes
Pae 8 www.sauder.com/service 427707
Remember:
Rihty tihty.
Lefty loosey.
These WOOD DOWELS
must be here.

Step 4
å Turn five ANGLED HEAD CAM SCREWS (5) into the
LARGE TOP (A).
å Carefully flip the parts over and fasten the LONG BACK (F)
and SHORT BACK (G) to the LARGE TOP (A). Tihten five
HIDDEN CAMS.
F
A
C
G
1
5
5
Pae 9www.sauder.com/service427707

å Fasten the LEFT FRAME (D) to the LEFT END (C) Use four
1-3/8" MACHINE SCREWS (16).
å Fasten the REAR FRAME (E) to the SHORT BACK (G). Use
four 1-3/8" MACHINE SCREWS (16).
å Fasten the FRAMES (D and E) to the TOP (A). Use four
1-3/8" WAFER HEAD SCREWS (15).
Step 5
D
E
C
G
1-3/8" WAFER HEAD SCREW
(4 used for the FRAMES to TOP)
15
1-3/8" WAFER HEAD SCREW
15
These holes
must be here.
These holes
must be here.
Pae 10 www.sauder.com/service 427707
1-3/8" MACHINE SCREW
(8 used in this step)
16
A