ESD DN-DP User manual

DN-DP Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 Page 1 of 21
esd electronics gmbh
Vahrenwalder Str. 207 • 30165 Hannover • Germany
http://www.esd.eu
Phone: [phone] • Fax: [phone]
DN-DP
PROFIBUS-DP / DeviceNet-Gateway
Hardware Manual
to Product C.2930.02

Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 DN-DP
Page 2 of 21
N O T E
The information in this document has been carefully checked and is believed to be entirely reliable.
esd makes no warranty of any kind with regard to the material in this document, and assumes no
responsibility for any errors that may appear in this document. In particular descriptions and technical
data specified in this document may not be constituted to be guaranteed product features in any legal
sense.
esd reserves the right to make changes without notice to this, or any of its products, to improve
reliability, performance or design.
All rights to this documentation are reserved by esd. Distribution to third parties and reproduction of
this document in any form, whole or in part, are subject to esd’s written approval.
© 2017 esd electronics gmbh, Hannover
esd electronics gmbh
Vahrenwalder Str. 207
30165 Hannover
Germany
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Internet: www.esd.eu
This manual contains important information and instructions on safe and efficient
handling of the module. Carefully read this manual before commencing any work and
follow the instructions.
The manual is a product component, please retain it for future use.
Trademark Notices
PROFIBUS is a registered trademark of PROFIBUS Nutzerorganisation e.V..
DeviceNet
TM
is a trademark of the Open DeviceNet Vendor Association, Inc (ODVA).
All other trademarks, product names, company names or company logos used in this manual are reserved by their
respective owners.

DN-DP Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 Page 3 of 21
Document file: I:\Texte\Doku\MANUALS\CAN\DN-DP\Englisch\DN-DP_Hardware_en_15.wpd
Date of print: 2017-03-29
PCB version: DN-DP Rev. 1.0
Changes in the chapters
The changes in the document listed below affect changes in the hardware and firmware as well as
changes in the description of facts only.
Version Chapter Changes versus previous version
1.2
- Safety instructions inserted
1. Maximum of 240 data byte per direction
6. Order information of engineering manual deleted
- EC Declaration of Conformity appended
1.3
- Safety Instructions revised
2. New chapter: “Quick Start”
5.1 Phoenix Contact part number of cable connector corrected
5.4 Chapter “Conductor Connection/Conductor Cross Sections” inserted
6. New chapter “References”
7. New Declaration of Conformity inserted
8. Order information revised
1.4 - Chapter 2.”Quick Start” deleted
1.5 - SafetyInstructions revised , Classification inserted
1. Description of DN-DP revised
Technical details are subject to change without further notice.

Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 DN-DP
Page 4 of 21
Classification of Warning Messages and Safety Instructions
This manual contains noticeable descriptions, warning messages and safety instructions, which you
must follow to avoid personal injuries or death and property damage.
This is the safety alert symbol.
It is used to alert you to potential personal injury hazards. Obey all safety messages and
instructions that follow this symbol to avoid possible injury or death.
DANGER, WARNING, CAUTION
Depending on the hazard level the signal words DANGER, WARNING or CAUTION are used to
highlight safety instructions and warning messages. These messages may also include a warning
relating to property damage.
DANGER
Danger statements indicate a hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Warning statements indicate a hazardous situation that, if not avoided, could result in
death or serious injury.
CAUTION
Caution statements indicate a hazardous situation that, if not avoided, could result in
minor or moderate injury.
INFORMATION
INFORMATION
Notes to point out something important or useful.

DN-DP Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 Page 5 of 21
Safety Instructions

When working with the DN-DP module follow the instructions below and read the manual
carefully to protect yourself and the DN-DP module from damage.

The permitted operating position is specified as shown (Fig. 2). Other operating positions are
not allowed.

Do not open the housing of the DN-DP module

Never let liquids get inside the DN-DP module. Otherwise, electric shocks or short circuits may
result.

Protect the DN-DP module from dust, moisture and steam.

Protect the DN-DP module from shocks and vibrations.

In order to prevent overvoltage damage due to thunder storm, unplug the DN-DP from
PROFIBUS-DP and the DeviceNet beforehand.

The DN-DP module may become warm during normal use. Always allow adequate ventilation
around the DN-DP module and use care when handling.

Do not operate the DN-DP module adjacent to heat sources and do not expose it to unnecessary
thermal radiation. Ensure an ambient temperature as specified in the technical data.

Do not use damaged or defective cables to connect the DN-DP module .

In case of damages to the device, which might affect safety, appropriate and immediate
measures must be taken, that exclude an endangerment of persons and domestic animals and
property.

Current circuits which are connected to the device have to be sufficiently protected against
hazardous voltage (SELV according to EN 60950-1).

The DN-DP module may only be driven by power supply current circuits, that are contact
protected. A power supply, that provides a safety extra-low voltage (SELV or PELV) according
to EN 60950-1, complies with this conditions.
Conformity
The DN-DP is an industrial product and meets the demands of the EU regulations and EMC
standards for industrial environments printed in the conformity declaration at the end of this manual.
Warning: In a residential, commercial or light industrial environment the DN-DP may cause radio
interferences in which case the user may be required to take adequate measures.
Qualified Personal
This documentation is directed exclusively towards qualified personal in control and automation
engineering. The installation and commissioning of the product may only be carried out by qualified
personal, which is authorized to put devices, systems and electric circuits into operation according
to the applicable national standards of safety engineering.

Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 DN-DP
Page 6 of 21
Intended Use
The intended use of the DN-DP is the operation as PROFIBUS-DP/DeviceNet-Gateway.
The esd guarantee does not cover damages which result from improper use, usage not in accordance
with regulations or disregard of safety instructions and warnings.

The DN-DP is intended for indoor installation only.

The operation of the DN-DP in hazardous areas, or areas exposed to potentially explosive
materials is not permitted.

The operation of the DN-DP for medical purposes is prohibited.
Service Note
The DN-DP does not contain any parts that require maintenance by the user. The DN-DP does not
require any manual configuration of the hardware. Unauthorized intervention in the device voids
warranty claims.
Remove all cables before cleaning. Clean the device with a lint-free cloth. Cleaning agents or
solvents are not suitable.
Disposal
Devices which have become defective in the long run have to be disposed in an appropriate way or
have to be returned to the manufacturer for proper disposal. Please, make a contribution to
environmental protection.
Typographical Conventions
Throughout this manual the following typographical conventions are used to distinguish technical terms.
Convention Example
File and path names /dev/null or <stdio.h>
Function names open()
Programming constants NULL
Programming data types uint32_t
Variable names Count
Number Representation
All numbers in this document are base 10 unless designated otherwise. For hexadecimal numbers
h
is appended . For
example, 42 is represented as 2A
h
in hexadecimal format.

Contents Page
DN-DP
Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 Page 7 of 21
1. Overview .................................................................8
2. Hardware Installation ......................................................10
2.1ConnectingDiagram...................................................10
2.2LEDsandCodingSwitches .............................................11
2.2.1LEDAssignment ................................................11
2.2.2 Setting PROFIBUS-DP Address via Coding Switches . . . . . . . . . . . . . . . . . . . . 12
3. Technical Data ............................................................13
3.1GeneralTechnicalData.................................................13
3.2PowerPCUnit .......................................................13
3.3DeviceNet-Interface ...................................................14
3.4PROFIBUS-DPInterface ...............................................14
4. Connector Pin Assignment ..................................................15
4.1 DeviceNet (X1100, 5-pol. COMBICON-Style) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2 PROFIBUS-DP Interface (X1000, 9-pin DSUB, female) . . . . . . . . . . . . . . . . . . . . . . . 16
4.3PowerSupplyVoltage(X100) ...........................................17
4.4 Conductor Connection/Conductor Cross Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. References ...............................................................19
6. Declaration of Conformity ..................................................20
7. Order Information .........................................................21

i
Overview
Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 DN-DP
Page 8 of 21



 
 






!
!"
#
!$
#
!$
%
&
'
(
)
&
*
&
+
,-./012
3-4/5-..25
6$"78
!$
789
878  :"7 
9 
;<
="6 >
?@A-.2
3BCDE3BF
G@A-.2
3BCDE3BF
7
>
3-HI41 JKI/LM2N
O-5 @PHH52NN
 QRR$
S TU
87 8 :"7
JVDW
3-442L/-5
X

1. Overview
Fig. 1: Block circuit diagram
The DN-DP module can link any PROFIBUS
®
DP master to a DeviceNet
TM
network. The DN-DP
gateway operates as a PROFIBUS DP slave-I/O component.
At the DeviceNet network the DN-DP gateway can operate as a scanner to control several DeviceNet
slave devices or as a single slave device to be connected to one DeviceNet scanner.
The DN-DP module is always configured via a PROFIBUS DP master.
As a DeviceNet scanner, several DeviceNet slave devices can be addressed. The maximum number is
between 20 and 40. This number depends on the configured PROFIBUS DP slave I/O type of each
DeviceNet slave device. Up to a total of 312 user data bytes canbeconfigured for eachDeviceNet slave
device. For each direction up to 240 user data bytes can be set up.
At the configuration ofthe DN-DP Gatewayas DeviceNet Slave theDN-DP gatewaycanbe configured
as exactly one single DeviceNet slave. With this configuration, it can be connected to exactly one
DeviceNet scanner.
With the DN-DP gateway you can couple DeviceNet modules to e.g. a SIMATIC-S7.
The DN-DP module is equipped with a PowerPC 405 EP, which buffers the CAN- and PROFIBUS
data into a local SDRAM. The firmware is stored in the Flash. Internal, fixed parameters are stored
in a serial EEPROM.
The DN-DP supports all DeviceNet compatible bit rates. The PROFIBUS DP Slave interface

Quick Start
DN-DP
Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 Page 9 of 21
automatically recognizes all usual bit rates up to 12 Mbit/s.
The PROFIBUS DP as well as the DeviceNet interface are electrically isolated.
The module can be configured via a PROFIBUS configuration tool, e.g. the PLC SIMATIC
Manager or the TIA Portal.

Hardware Installation
Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5 DN-DP
Page 10 of 21
2. Hardware Installation
2.1 Connecting Diagram
Fig. 2: Connections of the DN-DP module
INFORMATION
The connector pin assignment can be found on page 15 and following.
For conductor connection and conductor cross section see page 18.
.