ESKUTE Netuno User manual

When open the bike's caon box, take out E-bike and use tools to cut o the package strings.
1.1 Use inner hexagon tool to loosen
the stem cover and don't tighten
all bolts immediately before
adjusting the handlebar in a
propey angel and position.
1.2 Then tighten with tool.
1 Install the Handlebar
2.1 Take out the front fork protector
from the front fork (Please note:
Front fork protector is used to
prevent the forks from
being deformed during transpo.
It belongs to the packing material.
You can just throw away this
accesso!)
2.2 Take out the quick release
from wheel and unscrew
the bolt from the
quick release.
2 Install Front Wheel
Netuno E-Mountain Bike Installation Guide
LED Display Installation Instruction
1. Select the CR-V5mm hexagonal wrench (the
Allen Key) in the tool kit that comes with the
e-bike, and remove the screw in the center
of the standpipe;
2. Remove the top four protection rings and
protective lid;
3. Install the display to the stem.
5. Put the protective lid on the display; 6. Tighten the screws on both sides to
complete the installation of the
display.
4. Adjust the display, put the screw back, and
tighten it to the rmest state to ensure safe
riding.
Discard

3 Install the Front Light
Mount the headlight
on the front fork
bracket with screws.
Check 2 pedals, the
one imprinted “L”
should install on the
left side and “R” on
the right side. Please
use a wrench to
tighten them.
1 Open the seat post
and saddle, then
install the rear
reector;
2 Adjust seat post to
the height that
suits your riding
position best
and tighten quick release. (Please make sure
that the quick release is tightened rmly.)
4 install Pedals 5 Install the Seat Post
2.3 Install the front wheel on the fork.
Make sure the fork is attached to
the axle and make sure the disc is
placed in the middle of the brake.
2.4 Inse quick-release axle into
spring and tighten screw
Quick release nut to be at the
same end as the brake.
Each ESKUTE e-bike comes with two copies of the batte key. Charging the batte on the bike is likely to result in infrequent use of the batte
key however, is required for maintenance and repair, so please keep this in mind when you store your Key.
1 Open the box of batte.
2 Tube the batte to correct angle and inse the batte into the holder gently, press it down and lock automatically.
3 Charging the batte outside the bike.
Inse the key to unlock the batte, and then pull the batte upwards.
Remove the batte.
Connect the charger to the batte.
Connect the charger to a power outlet.
The charging process can be stopped at any time.
Disconnect the charger rst from the power outlet and then from the batte.
Replace the batte and make sure it is correctly aligned at the bottom.
Press the top of the batte until you hear a "click" to make sure the batte is properly secured.
Pull the key out.
Your ESKUTE e-bike is ready for use
6 Install Batte
Make sure you always have at least one spare key.
Keep spare keys in a safe place for repairs, maintenance, and emergencies.
Please bring the key with you when you contact your dealer for seice or repair.
7 Range and Speed Selection
To increase the range, we recommend switching to speeds For staing and low speed it is better to use a lower gear. At higher speeds, a
higher gear should be selected. Reduce the pressure on the pedals during gear shifting for obtaining stable suppo and improved range.
High speed, high gear.
Low speed, low gear.
Reduce pressure on the pedals when shifting gears.
Distributor: Yimei Network Technology Co., Ltd
Website: https://www.eskute.co.uk/
Email: [e-mail]
Manufacturer: Myatu Europe Intelligent Technology Sp.z o.o
Add: Prologis Park Wroclaw 1, building
DC 1 A, Magazynowa 1 street
55-040 Bielany Wroclawskie, Poland
MADE IN POLAND