ESP MAGDUO MAGDUOSRSQ User manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS
MAGDUOSRSQ MAGDUO Wall Sounder Red
MAGDUOSWSQ MAGDUO Wall Sounder White
26-1661-01
General Description
The MAGDUO Wall Sounder unit allows for audible indication when the system enters an alarm condition. This
device is compatible with the MAGDUO 2-wire range of Fire Alarm equipment and comprises a 2-wire zone-
powered sounder. This device may be installed on the same zone as the FlexiPoint detector/sounder and
associated MAGDUO devices.
Before Installation
The Sounder must be installed in compliance with the control panel installation manual. The installation must
also meet the requirements of any local authority. For maximum performance the sounder should be installed in
compliance to BS5839 Pt1 : 2017.
Spacing
It is recommended spacing of sounders in accordance with BS5839 Pt1. For more specific information regarding
sounder spacing, placement and special applications please refer to BS5839 Pt1 : 2017.
Device Installation
Surface Mounting
Fix the surface back box to a flat vertical surface using at least two of the four mounting
holes provided. The back box may be drilled to allow cable access as required. A 20mm
hole is already provided at the rear. Zone cabling may be connected to the terminals in
the back box.
Flush Mounting
The MAGDUO Wall Sounder may be flush mounted utilising the optional adaptor
plate, combined with any standard single gang flush mounting back box (with a
minimum internal depth of 47mm).
After installing the back box securely, attach the adaptor plate using the two screws
provided, and terminate your cables directly into a flying terminal block.
Installation 2nd Fix
Once all testing has been carried out on the cabling and ‘continuity & integrity’ has
been proven, the MAGDUO Wall Sounder front may be installed.
Connect the wires from the MAGDUO Wall Sounder front in to the appropriate terminals
in the back box according to the wire colours. The MAGDUO Wall Sounder front may then
be installed by locating the upper mounting hooks into the back box and then pushing the
unit gently home. The single fixing screw may then be tightened as required.
Please remember that all high voltage testing must be carried out before the installation
of the MAGDUO Wall Sounder front unit, otherwise the electronics will be damaged.
https://www.espuk.com/technical_support/
product_manuals/?cat=4

26-1661-01
Connections
MAGDUO Wall Sounders can be mixed on the same zone as other types of MAGDUO device. The above
diagram shows how to make the zone positive, zone negative and screen connections between the control
panel and MAGDUO Wall Sounder. Refer to the instruction leaflets supplied with other MAGDUO devices for
their equivalent wiring/terminal labelling details.
Please note that the E terminal on the MAGDUO Wall Sounder should only be connected to the zone cable
screen and NOT to the building earth. The cable screen is connected to earth at the panel end only, via the
zone “SCRN” terminal (or EARTH terminal on the MAGDUO panel). It is important to maintain the screen
continuity in order to protect against data corruption from interference.
Remember that the device at the end of the line must have its EOL signal activated using the
relevant DIL switch. Do not use a resistor or capacitor (or another manufacturer’s End of Line
device) as the end of line, as this may prevent correct operation of the zone.
DIL Switch Settings
The detector DIL switches may be used to program the operation of
the sounder. They may be altered whilst the device is still powered or
the system may be powered down completely.
The last device on the circuit must have the EOL signal enabled
(switch number 1 in the ‘ON’ position).
DIL SWITCH SETTINGS
1
2
3
4
End of line
Enabled
ON
Disabled
OFF
Sound Levels
High
ON
Low
OFF
Sound Patterns
Sound OFF
ON
ON
Dual Tone UK Evacuate –800 & 970 Hz
ON
OFF
Slow Whoop Up - 500 to 1200 Hz sweep up
OFF
OFF
Dual Tone French Warble –440 & 550 HZ
OFF
ON
SWITCH OFF
SWITCH ON
1 2 3 4
O N
E

26-1661-01
Technical Data
Dimensions Width.......................................................89 mm
Height......................................................89 mm
Flush Depth Protruding ...........................34 mm
Surface Depth .........................................62 mm
Operating Temperature .................................................................-10oC to +50oC
Voltage Ranges DC Output from Mains Powered Panel...25.5 to 35V DC
DC Output from Battery Powered Panel.20 to 26V DC
Operating Current (Typical) Quiescent ................................................185 uA
End of line ON if applicable.....................175 uA
(in addition to Quiescent)
Alarm Sounding –Sounder High.............14.5 mA
Alarm Sounding –Sounder Low .............12.6 mA
Device Loading Units Max Loading Units per zone ...................160 DLU
Sounder High. .........................................14.5 DLU
Sounder Low...........................................13.0 DLU
Volume Level Sounder High ..........................................85+ dB(A)
(@ 1m anechoic, Dual Tone) Sounder Low...........................................65+ dB(A)
Flammability .................................................................UL94-V2
IP Rating .................................................................IP 21C
0832
Elite Security Products LTD
Unit 7 Target Park, Shawbank Road, Lakeside, Redditch, B98 8YN
England
11
DoP-MAGDUOSWSQ-01
EN54-3: 2001 +A1: 2002 +A2: 2006
Sounder Technical Data See: 26-1649
Intended for use in the fire detection and fire alarm
Systems in and around buildings
Essential characteristics
Performance
Nominal activation conditions/Sensitivity,
Response delay (response time) and
performance under fire conditions
Pass
Operational reliability
Pass
Durability of operational reliability and
response delay, Temperature resistance
Pass
Durability of operational reliability,
Vibration resistance
Pass
Durability of operational reliability,
Humidity resistance
Pass
Durability of operational reliability,
Corrosion resistance
Pass
Durability of operational reliability,
Electrical stability
Pass
Durability of operational reliability,
Resistance to ingress
Pass
Technical Support
Due to the complexity and inherent importance of a life risk type
system, training on this equipment is essential, and
commissioning should only be carried out by competent persons.
ESP’s policy is one of continual improvement and the right to
change a specification at any time without notice is reserved.
Whilst every care has been taken to ensure that the contents of
this document are correct at time of publication, ESP shall be
under no liability whatsoever in respect of such contents. E&OE.
www.espuk.com