Esq ASTON 1/5 User manual

Operating Instructions
ASTON 1/5 CHRONOGRAPH
A chronograph combines two time-keeping functions. It incorporates
a device to measure intervals of time independent of the regular time
shown on the dial.Your ESQ by Movado Aston Chronograph may be
used to time events up to two hours in duration, in 1/5 of-a-second
increments.
NOTE: After 2 hours of continuous running, the chronograph will stop
and reset automatically to preserve battery life.
Setting the Time:
1. Pull crown out to position 3. (Watch will stop.)
2. Turn crown in either direction to move hands to desired time.
Be sure to take AM/PM into account so that date changes at midnight,
not noon.
3. Push crown back in to position 1. (Watch will restart.)
NOTE: To set time to exact second, pull crown out to position 2 precisely
when small seconds hand Sreaches <<60>> position. (Watch stops.)
Adjust time to one minute ahead, and take an accurate time signal, from
a radio news station, for example. When audible tone signals exact time,
immediately push crown back in to position 1. (Watch will restart, now
set to the exact time.)
Setting the Day:
1. Pull crown out to position 3. (Watch will stop.)
2. Turn crown in either direction to move hands forward or back. Each
time the hands complete a 24-hour revolution and pass midnight,
Day indicator hand Fwill move ahead or back by one day.
3. Once correct Day has been reached, set hands to correct Time,
following instructions above.
4. Push crown back in to position 1. (Watch will restart.)
Setting the Date:
1. Pull crown out to position 2. (Watch will keep running.)
2. Turn crown clockwise to move hands forward. Each time the hands
complete a 24-hour revolution and pass midnight, the date shown in
Date display Dwill advance by one number.
3. Once correct Date has been reached, push crown back in to position 1.
CAUTION: Never set the date when the hands are between 9:00 PM
and 12:30 AM, while automatic date changing is in progress. Doing so
could damage the calendar mechanism.
Chronograph Function Overview
Use buttons Aand Bto operate the chronograph. Pressing button A
the first time will start the chronograph. While the chronograph is run-
ning, once the chronograph fifths-of-a-second counter hand Chas com-
pleted one turn, minute-counter hand Ewill jump ahead one minute.
Pressing button Aa second time will stop the chronograph. Pressing
button Bwill reset chronograph hands Eand Cto zero. Adjusting the
time does not stop the chronograph, but it does block buttons Aand B
for as long as the crown is pulled out.
IMPORTANT: Crown must be in position 1 and hands must be at zero
before chronograph is started. Press button Bto reset hands to zero.
Do not push button Aor Bwhile crown is pulled to position 2 or 3.
If button Aor Bis accidentally activated while crown is not flush against
case, one or both chronograph hands may become de-synchronized.
Should this occur, see directions for synchronizing hands at end of
following instructions.
Simple chronograph functions:
To measure the duration of a single, non-stop event:
1. Press button Ato start chronograph.
2. Press button Aa second time to stop chronograph, and read the 2
chronograph hands to determine elapsed time, for example: 14 minutes;
37 and 3/5 of a second.
3. Press button Bto reset chronograph to zero.
Accumulated time functions:
To measure the combined time of a series of shorter events, for example
the actual playing time of a football game, where play is repeatedly
interrupted:
1. Press button Ato start chronograph.
2. Press button Aa second time to stop chronograph.
3. Press button Aagain to resume measurement.
4. Press button Aa fourth time to stop chronograph again.
NOTE: Each time you stop chronograph, chronograph hands will indicate
total accumulated time.
Repeat steps 1 and 2 to add each additional interval of time.
5. After you have taken your final accumulated time reading, press button
Bto reset chronograph hands to zero.
Split-time or intermediate time functions:
To take intermediate time readings as a race progresses:
1. Press button Ato start chronograph.
2. Press button Bto momentarily stop chronograph.
3. Read off the intermediate time, for example:10 minutes, 26 and 2/5
of a second.
Legend
H- Hour hand
M- Minute hand
S- Small seconds hand
F- Day indicator hand
C- Center-mounted chronograph fifths-of-a-second hand
E- Chronograph 30-minutes counter
D- Date display
1, 2, 3 - Crown positions
A- Chronograph start/stop push-button
B- Chronograph split/reset push-button
20
28
30
S
S
F
T
T
M
W
10 40
0
20
E
1
A
B
C
D
F
2
S
HM
3

4. Press button Bto resume chronograph function. Hands will catch up
with ongoing event.
5. To read a second split time, press button Bagain.
Repeat steps 2 through 4 to take any additional split times.
6. Press button Ato stop chronograph.
7. Take a reading of the final time, for example: 27 minutes, 3 and 4/5
of a second.
8. Press button Bto reset chronograph hands to zero.
To Synchronize Chronograph Hands:
After a battery change or in the event of an error, you may need
to manually adjust one or more chronograph hand to align them all
correctly at their zero positions.
1. Pull crown out to position 2.
2. Use push-button Bto adjust chronograph 30-minutes counter hand E;
press and hold button to advance hand rapidly.
3. Use push-button Ato adjust center-mounted chronograph fifths-of-a-
second hand C; press and hold button to advance hand rapidly.
4. When both chronograph hands are aligned at 12 o’clock, push crown
back in to position 1.
Timing hands are now synchronized at zero position, and chronograph is
ready for use.