eSSL TL200 User manual

IInnssttaallllaattiioonn IInnssttrruuccttiioonn
Version: 1.0
Date: Aug., 2016
TL200 Fingerprint Lock With Voice Guide Feature
www.esslsecurity.com

Before Installation
1
Diagram
B
J
K
N
M
A
C
C
D
E
F
H
G
O
P
I
L
Q

Packing List
GH
M
BCIE
20mm
15mm
NF
2
105mm
60mm
D
L
125mm
85mm
Wooden Door Security Door
10mm
85mm
A
45mm
55mm
60mm
70mm
85mm
30mm
45mm
55mm
70mm
J
K
Q

5
Door Preparation
1. Check door thickness, prepare the proper screws and spindles.
Door Thickness D Spindle L Spindle J Screw K Screw
35-50 mm 30 mm 45 mm
50-60 mm 55 mm
55-65 mm 60 mm
65-75 mm 105 mm 55 mm 70 mm
75-90 mm 125mm 70 mm 85 mm
60 mm
85 mm
45 mm
85 mm
3

GE
Left Inward Right Inward
Left Outward Right Outward
EG
E
GEG
2. Check door open direction.
Note : 1. Please install the mortise and strike plate according to the above pictures.
3. Check door type.
Mortise without hooks is applied to wooden door,
and mortise with hooks is applied to security door.
(Without hooks) (With hooks)
4

180°
7
Tips
1. How to change the direction of latch bolt?
Step1: Push the switch to the end
Step2: Push the latch bolt into the mortise
Step3: Rotate the latch bolt at 180° inside mortise, then loose it.
2. How to change the handle direction?
Front Lock
Loose
screw
Back Lock

5
Œ
Ž

3.How to use mechanical key ?
Insert the key into key hole and
rotate 90°, then press down the
handle to open the door.
4. How to use emergency power?
9V Alkaline
Battery
(6LR61)
5. How to change the location of stud bolts?
M3
M5
Note: For the door with the existed holes, you can adjust stud bolts location
to make the lock suitable.
Step1: Twist down the ten M3 screws and M5 stud bolt to take down
the mounting plate.
6

Step2:Twist down the other stud
bolt.
Note: There are four
square holes to be used.
Note: There are two
round holes to be used.
7

Cautions
1. New lock is configured to grant ANY fingerprint access to unlock.
2. Please register one administrator at least for the new installed lock, If there is no any
administrator, registration for normal users and temporary users are not allowed.
3. The lock is equipped with mechanical keys for manual unlocking. Remove mechanical
keys from the package and keep them in a safe place.
4. To power on the lock, eight alkaline AA batteries (not included) are required.
Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove batteries when the lock is in working state.
6. Please replace the battery soon when the lock prompts the voice of low battery.
7. The operation of setting lock has a stand-by time limit of 7 seconds. Without any
activity, lock will shut off automatically.
8. Keep your fingers clean when using this lock.
8

F
1. Drill holes on the door 2. Install the mortise(E)
desired handle
height
E
F
E
9
door thickness
35~90mm
center line of the
handle
Backset 60mm
Note1:Align the template along the vertical
center line of the mortise(E)at the desired
handle height, and tape it to door.
Note2:Mark the holes first, then start drilling.
Installation