ETC Echoflex Dual Tech User manual

Echoflex Installation Guide
Dual Tech Switch-mount Occupancy Sensor
Main Of fice nSquamish, BC, Canada nToll Free [phone] nPhone [phone] nFax [phone]
Email [e-mail] nWeb echoflexsolutions.com nProduct information and specifications subject to change.
© 2018 Echoflex Solutions, Inc. nEchoflex intends this document to be provided in its entirety.
8186M2187 nRevision A nReleased 2018-09
Overview
The Elaho Dual Tech Switch-mount Occupancy Sensor is a switch station with
a built-in sensor that uses passive infrared (PIR) and acoustic detection to
provide reliable occupancy and vacancy sensing for lighting control.
The Dual Tech Switch-mount Occupancy
Sensor is available in one and two-button
models, and is available with white,
black, cream, or gray wall plate.
Each button is backlit by both blue and amber LEDs to show changes in status.
The sensor provides a 180 degree field of view with up to 45 feet (13.7 m)
radius for large motion detection.
This document guides you through the installation and local configuration and
setup of the Dual Tech Switch-mount Occupancy Sensor.
Custom Configuration
For more information about the custom configuration options available using
ElahoAccess, reference the ElahoAccess Mobile App integrated help system.
Note: Settings made using ElahoAccess are applied only when the
function selection switch is set to Custom (middle position). Reference
Function switch on page11.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Prepare for Installation
Dual Tech Switch-mount Occupancy Sensors ship with electronics, a decorator
style wall plate, and a termination kit. The sensor may be installed into an
industry standard back box (provided by others) or surface mounted back box
(sold separately and available from Echoflex).
Compliance
•
UL/cUL listed, complies with UL508A, UL916, and CSA C22.2 No. 14
•
CE compliant
For use with Echoflex dimming and relay products.
Environment
Ambient
For indoor, commercial controls use only. Indoor installation only. The sensor
operates in ambient temperatures of -10° C to 40° C, with a maximum of
90% non-condensing humidity.
Installation
Echoflex recommends paying special attention to the installation
environment:
•
When operating in PIR only modes, the sensor must have an
unobstructed view of the room. Do not mount behind or near tall
cabinets, shelves, hanging light fixtures, etc.
•
Do not install the sensor within eight feet from an HVAC airflow
duct/vent.
•
Install the sensor where it cannot easily sense movement in areas
outside of the intended space, such as hallways, glass partitions, or
adjacent rooms.
Note: In areas of increased noise activity, enabling PIR only mode may
allow for better vacancy detection results. Reference Rotary and
DIPSwitches on page5.
Dual Tech Switch-mount Occupancy Sensor Page 2 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Wire Specification
The Dual Tech Switch-mount Occupancy Sensor utilizes EchoConnect®for
power and for data communications with an Elaho control system.
EchoConnect is a bidirectional protocol that uses one pair of wires (data + and
data -) for both data and power. Echoflex recommends using Belden 8471 (or
approved equal) Class 2 wire. The total combined length of an EchoConnect
wire run (using Belden 8471 or equal) may not exceed 1,640 feet (500 m).
Note: All control wiring should be installed and terminated by a
qualified installer and should follow standard wiring installation practices.
Leave approximately 8" (20cm) of wiring in the back box for connection
and to allow slack for future service needs.
Note: Echoflex requires that all Elaho stations and devices be grounded
for ESDprotection. Pull an additional 14AWG (2.5 mm2) wire for
grounding when control wires are not installed in grounded metal conduit.
Note: When using Category 5 (or equivalent) cable on the EchoConnect
communication bus, please note the following:
•
Cat5 wiring must be terminated using EchoConnect Cat5
Termination Kit and must be installed using a bus topology.
Refer to the installation guide that is provided with the Cat5
Termination Kit (8186A1207) for information to terminate
Cat5 wiring.
•
Not all topologies are supported using Cat5; careful planning
is required to ensure the proper termination kits are available
and the wire is pulled appropriately.
Parts and Supplies
The following parts and supplies are included with the sensor:
•
mounting screws
•
EchoConnect termination kit
•
WAGO 221 Series LEVER-NUTS®(wire termination connectors)
•
decorator style wall plate
Dual Tech Switch-mount Occupancy Sensor Page 3 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Installation
Installation should follow all local codes and standard electrical practices.
Note: NEC Class 2 product to be wired in accordance to NEC Article
725 and local jurisdiction requirements.
The switch box should be installed plumb and square for best results. Ensure
that the switch box is clean and free of obstructions and that all wiring is
installed correctly.
Dual Tech Switch-mount Occupancy Sensors ship with a termination kit for
use with Belden 8471 (or equivalent wire), and include power and ground wire
pigtails, receptacle spacers, and all required wire termination connectors for
installation.
Connect Wiring
1. Pull all required wiring (data+, data-) into the installed switch box. As
needed, pull an additional ESD ground wire (required only when the
sensor wiring is not installed in grounded metal conduit).
2. Connect sensor ESD ground wire pigtail.
a. Strip 7/16" (11 mm) of insulation from the ends of the sensor
ground wire pigtail, provided in the termination kit, and the
incoming ground wire.
b. Use one WAGO connector, provided in the termination kit, to
connect the sensor ESD ground pigtail and the incoming ground.
For sensors using grounded metal conduit, connect the ground
pigtail to the metal switch box ground location.
c. Install the ESD ground wire pigtail FASTON connector to the
mating receptacle on the sensor electronics.
3. Terminate EchoConnect wires. EchoConnect is topology free, you may
install the wires in any combination of bus, star, loop, or home-run.
a. Strip 7/16" (11 mm) from the ends of each power pigtail wire,
provided in the termination kit, and the installed control wires.
b. Use the WAGO connectors provided to connect the power pigtail
wires and the installed Belden 8471 control wires. One WAGO
should be used for the white wire pair (data +) and one for the
black wire pair (data -). Open the terminal levers on the WAGO
connector and insert the installed Belden 8471 wire and the lead
from the power pigtail into the terminals then close the levers.
c. Install the two pin connector from the power pigtail to the
mating receptacle on the sensor electronics.
Dual Tech Switch-mount Occupancy Sensor Page 4 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Rotary and DIPSwitches
Rotary and DIPswitch settings are accessible on the rear of the station.
Set Space and Address
The two rotary switches provide for
assignment of the sensor space and address.
Each sensor must be set to a unique station
address for the assigned space. By default,
these switches are set to Space 1, Address 1.
Commands are shared by all devices within n
assigned space.
1. Set the Space rotary switch to the
desired number (1 through 16) for the
space you want the sensor to control.
2. Set the Address rotary switch to desired address (1 through 16) for the
sensor identification in the selected space.
3.
CAUTION: Each device on the bus must have its address set to a
unique number (1 through 16) for the space it controls. If two or more
devices use the same address for the same space, the system will not
function properly.
Dual Tech Switch-mount Occupancy Sensor Page 5 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
DIP Switch Settings
DIP switches provide for designation of “Off” functionality, the ability to
disable amber button LEDs, and the ability to restore the sensor to its factory
defaults.
Switch # Use
1
1-button Dual Tech Switch-mount Occupancy Sensor only
•
When set to On, and the function switch is set to Preset, enables
Sequence toggle mode. Default position is Off.
2 button Dual Tech Switch-mount Occupancy Sensor only
•
When set to On (default), and the function switch is set to Preset, the
bottom button provides a Space Off command.
•
When set to Off, the bottom button controls the next consecutive preset
after the preset assigned to the top button.
2
Amber LED Disable - provides the ability to disable use of the amber
button LEDs.
•
When set to On, the amber button LEDs on the station will be disabled.
Only blue LEDs will illuminate.
•
When set to Off (default), the amber button LEDs on the station are
enabled. Amber LEDs are provided as the default so the station glows in
darkened spaces, allowing it to be easily located.
3 and 4
Vacancy Timeout
•
5 min = Switches 3 and 4 are Off
•
15 min = Switch 3 is Off and Switch 4 is On (default)
•
30 = Switch 3 is On and Switch 4 is Off
•
Auto = Both switches are On
5
Detection LEDs
•
When set to On (default), the occupancy detection LED illuminates when
movement is detected.
•
When set to Off, the occupancy detection LED is disabled unless the unit
is in Walk Test mode.
6
PIR Only Mode
•
When set to On, acoustic detection technology is disabled for the
sensor.
•
When set to Off (default), both PIR and acoustic detection technologies
are used by the sensor.
7unused
8
Restore to Defaults at boot
•
When set to On, then cycling power to the switch-mount station, the
unit restores to its factory default settings.
•
Off is the default setting
Dual Tech Switch-mount Occupancy Sensor Page 6 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Note: When the sensor Function switch is set to Custom, only DIP
switch number 8 applies. All other DIP switch settings are ignored.
Reference Station Configuration on page11 for local configuration settings
on your Dual Tech Switch-mount Occupancy Sensor. Reference the
ElahoAccess Mobile App integrated help system for details about custom
configuration using the ElahoAccess Interface.
Install Button Legends
Elaho Dual Tech Switch-mount Occupancy Sensors ship with standard button
legends installed beneath a clear lens.
Note: Customize and print your own button legends on standard
transparency. Download the button legend template provided on the
Echoflex website echoflexsolutions.com.
Each button can have a legend, installed beneath the button lens. To remove,
install, or replace a button legend you must first remove the bezel and button
lens from the station electronics.
1. Remove the bezel from the station
electronics.
•
Each corner of the bezel is provided
with a notch to assist with bezel
removal. Use a nail to lift a corner free,
then gently remove the bezel from the
station.
Dual Tech Switch-mount Occupancy Sensor Page 7 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
r
i
u
m
n
E
n
t
r
y
i
i
r
i
i
i
n
E
n
t
r
y
n
E
2. Remove the button lens.
•
Using the pads of your thumb, press on the lens
and slide the lens left, toward the hinge points.
3. Once the lens is removed, remove the existing
legend and insert a custom legend.
4. Replace the lens onto the button by aligning the
grooves of the lens to the button, then sliding the
lends in place starting at the hinge. Slide the lens
until it covers the entire button and clicks into
place.
5. Replace the bezel to the station electronics when
all legends and lenses are in place.
Install the Station
Receptacle spacers are provided for use in flush mount applications to help
align the station and cover flush against the wall.
1. Insert the station electronics
and wiring into the switch
box. To install multiple
stations (multi-gang), insert
the station electronics into
the box from the right to the
left side for the best
alignment and fit. The
alignment bracket will slightly overlap the station to the right when
properly installed.
2. Use spacers as needed to provide a flush mounted station.
a. Fold the spacer in a zig-zag fashion and press the stack together
to achieve the thickness needed to fill the gap between the
station, wall surface, and the switch box.
b. Cut off and discard the excess.
c. Place the stack between the station electronics and the flush
mounted switch box.
3. Secure each station electronics in place using the two screws provided.
If using spacers, insert the screws through the spacers as well.
CAUTION: To improve successful station and wall plate installation,
do not over tighten the screws. If screws are over tightened, button
activation can be negatively impacted.
Dual Tech Switch-mount Occupancy Sensor Page 8 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Install the Wall Plate
The wall plate is secured to the station with built-in magnets.
1. Align the top of the wall plate to the station
and angle the bottom approximately 20
degrees.
2. Hook the top of the wall plate to the tabs
located on the station electronics assembly.
To ensure the wall plate is hooked properly on
the top hook, wiggle it slightly side to side.
3. Swing the bottom of the wall plate down until
the magnets engage.
4. If the wall plate does not fully attach
automatically, wiggle the bottom of the plate
until all of the magnets are seated properly to
the station and the plate is secure.
Note: When installing a multi-gang wall plate and the stations are
misaligned in the mounting box, the wall plate will not attach properly.
Loosen the screws that secure the station to the box, adjust each station
to improve the alignment, secure the screws, then retry wall plate
installation.
Power Up and Test
Power Up
All EchoConnect terminations in the system must be made before applying
power to the system and sensor. When the sensor is powered up, the PIR and
acoustic detection LEDs illuminate for one minute for calibration and warm-
up, and then return to normal operation according to the configuration.
Both the PIR and acoustic detection features of the sensor will automatically
adjust sensitivity threshold to eliminate nuisance tripping. During this time,
sensor configuration is not allowed and no events are triggered.
Dual Technology Detection
When both PIR and acoustic detection are used, the following logic is
followed:
•
When the space is vacant, PIR detection and manual control can switch
the state to occupied.
•
When the space is occupied, PIR, acoustic detection, and manual
control can reset the vacancy timeout.
•
When occupancy in the space has only been triggered by acoustic
detection for 60 minutes, acoustic detection is disabled until the next
PIR detection event.
Dual Tech Switch-mount Occupancy Sensor Page 9 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
PIR (only) Detection
When acoustic detection is disabled (DIP switch 6 set to On), the following
logic is used:
•
When the space is vacant, PIR detection and manual control can switch
the state to occupied.
•
When the space is occupied, PIR detection and manual control can
reset the vacancy timeout.
Walk Test
The sensor offers a Walk Test mode, which shortens the vacancy timer to ten
seconds and allows for simple and quick verification of the sensor’s coverage
and range in the installed space.
Walk Test
1. Prepare the site for configuration.
a. Make certain the sensor and lighting
loads are powered and connected
for control by the Elaho control
system.
b. You will need direct access to the
sensor in order to place it into Walk
Test mode.
2. Remove the sensor wall plate to gain
access to the [Walk Test] button.
3. Press the [Walk Test] button on the top right of the sensor to enable
the Walk Test feature at the sensor. A green LED will begin to flash,
indicating Walk Test is enabled and the vacancy timer will be
shortened to ten seconds.
4. Move throughout the space including corners and areas that may
specifically be obscured from line of sight to the sensor. Each time the
sensor detects movement, the lens will illuminate red. If acoustic
detection is enabled, any sound detected will illuminate the lens
green.
5. Walk Test mode will automatically exit and return to normal operation
after five minutes. You can also manually terminate by pressing the
[Walk Test] button again.
Dual Tech Switch-mount Occupancy Sensor Page 10 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Station Configuration
The Dual Tech Switch-mount Occupancy Sensor has on-board switch and
button settings that are available from the front of the station when it is
installed and the wall plate is removed.
Program Mode
Press and hold the [Walk Test]
button 3 seconds to enter Program
Mode
Function switch
Preset
Custom
Zone
Program Mode
Program Mode allows adjustment of the consecutive range of presets or
zones assigned to the station. Placing the station in Program Mode allows you
to set a new starting preset or zone number for the station.
The programmed preset or zone that is associated to the first button control
is also the event/action that will occur with occupancy and vacancy detection.
Reference Program Preset Start (Basic Mode, Preset or Zone) on page13 .
Function switch
The Function switch determines how the controls of the sensor function. It has
behavior settings of Preset, Custom, and Zone.
Function switch: Preset
Setting the Function switch to Preset allows you to perform preset related
actions dependent on the switch-mount sensor type. Reference Station
Functionality on page15 for complete details of the button actions when
the switch-mount sensor is placed in Preset mode.
Preset Toggle Functionality
Preset toggle control functionality allows you to toggle the preset on and off
by pushing the assigned preset button.
•
A single button push activates / deactivates the preset that is assigned
to that button using a two second fade time.
•
A double button push activates / deactivates the preset that is
assigned to that button using a 1/2 second fade time.
Dual Tech Switch-mount Occupancy Sensor Page 11 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
When a preset is active, the button LED lights blue to indicate its active state.
If preset levels are altered while the preset is still active, the related button
LED will return to its default state, either off or amber. Reference Rotary and
DIPSwitches on page5 .
Use Off Functionality (2 button Switch-mount Sensor only)
“Use Off” functionality enables the last button on the station with a
dedicated space off action.
•
A single push of the “Off” button will set the level of all zones to zero
using a two second fade time.
•
A double push of the “Off” button will set the level of all zones to zero
using a 1/2 second fade time.
“Use Off” functionality is enabled when DIP switch 1 is set to On. Reference
page 5 .
Note: The one button switch-mount sensor does not recognize “Use
Off” functionality.
Function switch: Custom
Setting the Function switch to Custom (the middle switch setting) allows for
varied features either with or without ElahoAccess, although the presence of
ElahoAccess in the control system allows for an expanded feature set.
With ElahoAccess
ElahoAccess provides complete customization of the switch-mount sensor
when it is in Custom control mode. For more information on the configurable
device parameters and actions available, reference the ElahoAccess Mobile
App integrated help system.
Note: Changes made in ElahoAccess impact the Custom Function
switch setting of the sensor only. Preset and Zone Function switch
settings remain unaffected by the changes made while using ElahoAccess
configuration tools.
Without ElahoAccess
Reference Station Functionality on page15 for default functions when the
switch-mount sensor Function switch is set to Custom control mode and you
do not have ElahoAccess to customize the features.
Function switch: Zone
Setting the Function switch to Zone (the lowest switch setting) allows you to
manually control the level of a zone using on / off and space raise or space
lower (two button switch-mount sensor only) functionality.
Dual Tech Switch-mount Occupancy Sensor Page 12 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Zone Toggle Functionality
While the Function switch is set to Zone, the station allows you to toggle the
zone on and off. The controlled zone level raises to full or toggles off using a
1/2 or 2 second fade time, depending on the station type. Reference Station
Functionality on page15 .
Zone Raise / Lower Functionality
Zone raise / lower functionality varies depending on the switch-mount sensor
type. The one button switch-mount sensor provides zone raise functionality
only. The two button switch-mount sensor provides both zone raise and zone
lower functionality. Reference page 15 .
Program Preset Start (Basic Mode, Preset or Zone)
Note: Program Mode only affects station behaviors when the Function
switch is set to Preset or Zone, and does not affect any behaviors in
Custom mode.
Note: The preset that is configured to the first button control on the
sensor is also the event that will occur with occupancy detection. Space
Off will occur with vacancy detection.
1. Set the station Function switch to its highest position of Preset.
2. Press and hold the [Walk Test / Program Mode] button for three
seconds to enter Program Mode. The “Mode” LED illuminates (steady
amber) and the first button control LED for the station flashes the
current (first) preset controlled.(For example, if the first preset
controlled is Preset 3, the button LED will flash three times.)
3. Push button 1 to increase the starting preset number by one; any new
count always begins at 1. The station will update the LED indication,
flashing the LED to reflect the new preset number. (For example,
pushing the button control eight times will set the first preset for the
station to Preset 8.) All station preset controls will be consecutively
assigned beginning with the specified count.
4. When the desired preset number is set, press and release the [Walk
Test / Program Mode] button to save the new setting. The “Mode”
LED turns off and the button LED will blink the new setting before
returning to normal operation.
Note: To change the assignment to a lower number than what is
currently set, exit Program Mode then reenter Program Mode; the preset
count will restart at 1.
Dual Tech Switch-mount Occupancy Sensor Page 13 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Program Zone Start
Note: The zone that is configured to the button control(s) is also the
zone that will be activated at full with occupancy detection and
deactivated with vacancy detection.
1. Set the station Function switch to its lowest position of Zone.
2. Press and hold the [Walk Test / Program Mode] button for three
seconds to enter Program Mode. The “Mode” LED illuminates (steady
amber) and the first button control LED for the station flashes the
current (first) zone controlled.(For example, if the first zone controlled
is Zone 5, the button LED will flash five times.)
3. Push button 1 to increase the starting zone number by one; any new
count always begins at 1. The station will update the LED indication,
flashing the LED to reflect the new zone number. (For example,
pushing the button control three times will set the first zone for the
station to Zone 3.) All station zone controls will be consecutively
assigned beginning with the specified count.
4. When the desired zone number is set, press and release the Walk Test
/ Program Mode button to save the new setting. The “Mode” LED
turns off and the button LED will blink the new setting before
returning to normal operation.
Note: To change the assignment to a lower number than what is
currently set, exit Program Mode then reenter Program Mode; the zone
count will restart at 1.
Dual Tech Switch-mount Occupancy Sensor Page 14 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Station Functionality
One Button Switch-mount Sensor
The one button switch-mount sensor offers control of a single preset or zone
as determined by the Function switch setting.
Factory Defaults
The one button switch-mount sensor ships from the factory in the following
default settings:
•
Rotary switches are set to Address 1, Space 1. Reference Rotary and
DIPSwitches on page5 .
•
DIP switches 4 and 5 are set to On. All other switches are set to Off.
Reference page 5 .
•
With the Function switch set to Preset, Preset 1 is the default.
•
With the Function switch set to Zone, Zone 1 is the default.
•
With the Function switch set to Custom, Zone 2 is the default.
Preset
In Preset mode, an occupancy detection event plays the preset that is
configured to button 1, and the vacancy detection event plays Space Off.
The one button switch-mount sensor supports the following button actions:
Double-tap the button to toggle the
preset using a 1/2 second fade time.
Note: *When DIP switch 1 is set to On, Sequence toggle is enabled.
Reference page 5.
Dual Tech Switch-mount Occupancy Sensor Page 15 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Zone
In Zone mode, an occupancy detection event activates the zone that is
configured to button 1 at full, and the vacancy detection event deactivates the
Zone (set to 0%).
The one button switch-mount sensor supports the following button actions:
Double-tap the button to toggle the
preset using a 1/2 second fade time.
Custom
While the one button switch-mount sensor supports the following default
button actions in Custom mode, complete customization is available when
using ElahoAccess. In Custom mode, using default behaviors, an occupancy
event activates the zone that is configured to button 1 at full, and the vacancy
detection event deactivates the Zone (set to 0%).
Dual Tech Switch-mount Occupancy Sensor Page 16 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Double-tap the button to toggle the
preset using a 1/2 second fade time.
Two Button Switch-mount Sensor
The two button switch-mount sensor offers control of two presets or zones as
determined by the Function and DIP switch settings.
Factory Defaults
The two button switch-mount sensor ships from the factory in the following
default settings:
•
Rotary switches are set to Address 1, Space 1. Reference Rotary and
DIPSwitches on page5 .
•
DIP switches 1, 4, and 5 are set to On. All other switches are set to
Off. Reference page 5 .
•
With the Function switch set to Preset, Preset 1 is the default.
•
With the Function switch set to Zone, Zone 1 is the default.
•
With the Function switch set to Custom, Zone 2 is the default.
Preset
In Preset mode, an occupancy detection event plays the preset that is
configured to button 1, and the vacancy detection event plays Space Off.
The two button switch-mount sensor supports the following button actions:
Dual Tech Switch-mount Occupancy Sensor Page 17 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Double-tap the button to toggle the
preset using a 1/2 second fade time.
Note: *DIP switch 1 is set to On by factory default, which reserves
button control 2 for Off functionality. Reference Rotary and DIPSwitches
on page5 for instructions to change this default setting.
Zone
In Zone mode, an occupancy detection event activates the zone that is
configured to button 1 at full, and the vacancy detection event deactivates the
Zone (set to 0%).
The two button switch-mount sensor supports the following button actions:
Double-tap the button to toggle the
preset using a 1/2 second fade time.
Dual Tech Switch-mount Occupancy Sensor Page 18 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Custom
While the two button switch-mount sensor supports the following default
button actions in Custom mode, complete customization is available when
using ElahoAccess. In Custom mode, using default behaviors, an occupancy
event activates the zone that is configured to button 1 at full, and the vacancy
detection event deactivates the Zone (set to 0%).
Double-tap the button to toggle the
preset using a 1/2 second fade time.
Note: These are the default button actions for the switch-mount sensor
when the Function switch is set to Custom. For custom configuration
using ElahoAccess, reference the ElahoAccess Mobile App integrated help
system.
Dual Tech Switch-mount Occupancy Sensor Page 19 of 20 Echoflex Solutions, Inc.

Echoflex Installation Guide
Switch-mount Occupancy Sensor
Sensor Coverage
14 m
(45 ft)
14 m
(45 ft)
14 m
(45 ft)
15°
180°
9 m
(30 ft)
9 m
(30 ft)
Top View
Side View
Dual Tech Switch-mount Occupancy Sensor Page 20 of 20 Echoflex Solutions, Inc.