ETC echoflex ERUSB-C User manual

Echoflex Installation Guide
Cubicle Occupancy Sensor ERUSB-C
Corporate Headquarters nMiddleton, WI, USA |[phone]
Web echoflexsolutions.com |Email [email protected] |Support [email protected]
©2022 Echoflex Solutions, Inc. Trademark and patent info:echoflexsolutions.com/ip
Product information and specifications subject to change.
Echoflex intends this document to be provided in its entirety.
8188M2191 Rev A Released 2022-09
Overview
Sensor lens
Switch button
Antenna
The Cubicle Occupancy Sensor
(ERUSB-C) uses passive infrared (PIR)
technology to provide wireless
occupancy and switch control for small
spaces.
The ERUSB-C detects motion and
transmits the occupancy status to
control the lighting for a space. The
built-in button provides manual switch
control.
Powered by a USB port on any PC, the
ERUSB-C can be mounted at desk level or on a partition wall.
This document covers installation and operation. The product package
includes the interface and a 1m (3.2ft) USB 2.0 cable (type A to type
mini-B).
Prepare for Installation
To ensure optimal function, consider the installation environment and the
following guidelines:
•
For indoor use only. Operating temperature -10°C to 45°C (14°F to
113°F), 5%–92% relative humidity (non-condensing).
•
High-density construction materials and large metal appliances or
fixtures in the space may disrupt wireless transmissions.
•
Install the device within range of linked receivers or controllers, 24m
(80ft). Consider adding a repeater to extend reception range.
Supplies required to install (not provided):
•
Double-sided tape or Velcro®

Echoflex Installation Guide
Cubicle Occupancy Sensor
Installation
The ERUSB-C is powered through a USB port.
1. Plug the mini-B end of the USB cable into the ERUSB-C and the other
end into a computer USB port or wall plug adapter.
2. Use double-sided tape or Velcro to mount the ERUSB-C to the wall, if
required. Position the ERUSB-C facing the work station or underneath
the desk where the occupant’s legs rest.
Link to a Controller
The compatible target controller must be installed, powered, and within
range of the ERUSB-C. Both the occupancy sensor and the manual switch
must be linked separately using the following two processes.
Note: The linking process can be used both to link a device to a
controller and to unlink a linked device from a controller.
To link the occupancy sensor:
1. Press the [Learn] button on the controller to activate Link mode. If
necessary, refer to the related product documentation.
2. Press and hold the button on the ERUSB-C for five seconds.
3. Deactivate Link mode on the controller.
To link the manual switch:
1. Press the [Learn] button on the controller to activate Link mode. If
necessary, refer to the related product documentation.
2. Press the button on the ERUSB-C once and then press and hold the
button for five seconds.
3. Deactivate Link mode on the controller.
Note: To use the manual override, you may have to press the
button more than once as the ERUSB-C does not track the relay
state.
Cubicle Occupancy Sensor Page 2 of 4 Echoflex

Echoflex Installation Guide
Cubicle Occupancy Sensor
Sensor Operation
The ERUSB-C uses a short-range occupancy sensor lens to control lighting
in a small office or cubicle space. The button operates like a wall switch
to control ON and OFF manually. The green LED near the USB cable port
indicates the last switch action: on when last ON, and off when last OFF.
The sensor uses passive infrared (PIR) and has a detection range of 2m
(6.6ft) from the sensor and 2.5m (8.2 ft) in diameter.
2.5 m (8.2 ft)
2 m (6.6 ft)
Within this range, small movements
such as hand gestures like lifting a
coffee cup are detected as occupancy.
The ERUSB-C sends a wireless
message as follows:
•
Transmits a message immediately
when the occupancy state changes
from vacant to occupied.
•
Transmits a vacant state message if
no motion is detected for 200
seconds after last occupied state
message.
•
Transmits the current occupancy state every 100 seconds (heartbeat
message).
Cubicle Occupancy Sensor Page 3 of 4 Echoflex

Echoflex Installation Guide
Cubicle Occupancy Sensor
Compliance
For complete regulatory compliance information, see the Cubicle
Occupancy Sensor datasheet at echoflexsolutions.com.
FCC Compliance
Echoflex Cubicle Occupancy Sensor
(For any FCC matters):
Echoflex Solutions, Inc.
3031 Pleasant View Road
Middleton, WI 53562
[phone]
echoflexsolutions.com
This device complies with Part 15 of the FCCRules. Operation is subject to the following two
conditions:(1) this device may not cause harmful interference, and (2)this device must accept
any interference received; including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. Any modifications or changes to this product not expressly approved by
Electronic Theatre Controls, Inc. could void the user’s authority to operate the product.
Operation of this equipment in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at their own expense.
Contains FCC ID: SZV-STM300U
ISED Compliance
This device contains a license-exempt transmitter/receiver that complies with Innovation,
Science, and Economic Development Canada’s license-exempt RSSs. Operation is subject to
the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Contains IC ID: 5713A-STM300U
Conformité ISDE
Cet appareil contient un émetteur/récepteur conforme aux CNR d'Innovation, Sciences et
Développement économique Canada (ISDE) applicables aux appareils radio exempt de licence.
Son fonctionnement est soumis aux deux conditions suivantes:
1. L'appareil ne doit pas produire d'interférences.
2. L'utilisateur de l'appareil doit accepter toute interférence, même si l'interférence est
susceptible d'en compromettre le fonctionnement.
Contient ID IC: 5713A-STM300U
Cubicle Occupancy Sensor Page 4 of 4 Echoflex