ETI 50232162 User manual

USE AND CARE GUIDE
2 FT. LINEAR HIGH BAY LED LIGHT
Questions, problems, missing parts?
Call ETiSSL Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
THANK YOU
We appreciate the trust and confidence you have placed in ETi through the purchase of this LED light.
Visit us online to see our full line of products. Thank you for choosing ETi!
Part # HB-171-850-MV-D
Model # 50232162

3 ETiSSL.com
Please contact 1-855-384-7754 for further assistance.
2
Table of Contents
Table of Contents ...................................2
Safety Information ..................................2
Warranty ..........................................2
Pre-Installation.....................................3
Planning Installation ...............................3
Tools Required ....................................3
Package Contents .................................4
Hardware Included.................................4
Installation ........................................4
Suspension Mounting ..............................4
Surface Mounting .................................7
Downrod Mounting ...............................11
Care and Cleaning .................................14
Troubleshooting ...................................14
Safety Information
WARNING: Carefully read and understand
the information given in this manual before
beginning the assembly and installation.
Failure to do so could lead to electric shock,
fire, or other injuries which could be hazardous
or even fatal.
WARNING: Ensure the electricity to the wires
you are working on is shut off. Either remove
the fuse or turn off the circuit breaker.
Warranty
This product is warranted for a period of 5 years from the date of original purchase against defects in materials and
workmanship. If this product should fail to operate due to defects in material or workmanship within 60 months of purchase,
see www.ETiSSL.com for details. This product will be repaired or replaced, at ETi’s option. This warranty is expressly
limited to repair or replacement of product and liability for direct, incidental, or consequential damages is hereby expressly
excluded. Some states do not allow exclusions of direct, incidental or consequential damages, so the above limitation of
exclusion may not apply to you. This warranty gives the consumer specific legal rights, which vary from state to state.
WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS MANUFACTURED.
PACKAGE CONTENTS
Part Description Quantity
A Fixture Body 1
NOTICE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15B of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
□Reorient or relocate the receiving antenna.
□Increase the separation between the equipment and the receiver.
□Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
□Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
A
Pre-Installation
PLANNING INSTALLATION
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with the package
contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for
replacement parts.
NOTE: Keep your receipt and these instructions for proof of purchase.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
TOOLS REQUIRED
Wire
Strippers
Safety
Goggles Ladder Gloves
Pliers Phillips
Screwdriver
Power Drill
with Drill Bits
Wire
Cutters
Hook
Screws*
1/2 in. Snap-in
Bushing* Rigid Pipe**
* For Suspension
Mounting only
** For Downrod
Mounting only
NOTE: Eye hooks can be used as an alternate method of attaching the fixture to the ceiling when suspension mounting.

4 5 ETiSSL.com
Please contact 1-855-384-7754 for further assistance.
Suspension Mounting
1 Removing the power supply box
□Remove the four screws that attach the power supply box to the LED fixture body (A) using the power tool hex bit (FF).
□Put the screws aside as they will be needed to reattach the power supply box to the fixture body (A) in a later step.
□Lift the power supply box from the fixture body (A) and unplug the Quick Connect wires.
Quick
Connect
Knock-out Hole
Power Supply Box
A
A
Power Supply Box
Power Supply Box
Power Supply Box
A
Quick
Connect
A
Power Supply Box
2 Preparing the power supply box for wiring
□Remove the knock-out near the end of the power supply box.
□Fit a 1/2 in. snap-in bushing into the knock-out hole.
□Feed the wiring out through the bushing and knock-out hole.
□Reconnect the two ends of the Quick Connect wires.
□Align the screw holes in the fixture body (A) with the screw holes
in the power supply box.
□Fasten the fixture body (A) to the power supply
box with the previously removed screws, using the
power tool hex bit (FF).
Suspension Mounting (continued)
3 Mounting to drywall
□Drill two holes large enough to clear the closed flaps of the
butterfly nut on the toggle bolt (not included).
□Fasten the toggle bolt into the butterfly nut before
inserting the flaps into the ceiling.
□Tighten the toggle bolt.
Installation
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the
circuit breaker before removing the existing light fixture or installing the new one.
With power disconnected to the electrical box, remove the existing fixture. Make a sketch of how the current fixture is wired (by wire color)
or mark the wires with masking tape and a pencil so you will know how to properly reconnect the wires to the new LED light fixture.
4 Mounting to wood
□Drill two 1/16 in. diameter holes in the ceiling to
accommodate hook screws (not included).
□Fasten the combo wood-machine end into the metal hook.
□Tighten the hook screw (not included) into the wood.
FF
FF
AA
DD
EE FF
BB
CC
Pre-Installation (continued)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
AA Cover Plate 1
BB Cable Set 2
CC Chain with S-Hook 2
DD Electrical Box Screw 2
EE Wire Connector 3
FF Power Tool Hex Bit 1

6 7 ETiSSL.com
Please contact 1-855-384-7754 for further assistance.
A
CC
5 Preparing the fixture body for mounting
□Attach the hook on one end of the cable set (BB) to a hanging hole on the fixture body (A) and close the hook with pliers to
secure it.
□Attach the hook on the other end of the cable set (BB) to the other hanging hole on the same end of the fixture body (A) and
close the hook with pliers to secure it.
□Attach the S-hook on one end of the mounting chain (CC) to the center of the cable set (BB) and
close the hook with pliers to secure it.
□Repeat these steps with the second cable set (BB) and mounting chain (CC) on the
opposite end of the fixture body (A).
CC
BB BB
Suspension Mounting (continued) Suspension Mounting (continued)
7 Making the electrical connections
□Feed the electrical wires from the fixture (A) through the cover plate (AA).
□Connect the hot and neutral (black and white) wires from the fixture body
(A) to the same color wires from the electrical box.
□Connect the green wire from the fixture body (A) to the grounding wire from
the electrical box.
□If 0-10v dimming circuit is available, connect the purple and gray wires
from the power supply box to the same color wires from the electrical box.
□If dimming is not desired, wrap the ends of the purple and gray wires with electrical
tape to cover the wire.
□Cover the wire connections using the wire connectors (EE).
□Wrap the wire connectors (EE) with electrical tape for a more secure connection.
□Position the wires back inside the electrical box and attach the cover plate (AA) to the
electrical box using the electrical box screws (DD).
8 Restoring power
□Restore power at the electrical panel.
□Turn on the light switch to activate the fixture.
1 Removing the power supply box
□Remove the four screws that attach the power supply box to the LED fixture body (A) using the power tool hex bit (FF).
□Put the screws aside as they will be needed to reattach the power supply box to the fixture body (A) in a later step.
□Lift the power supply box from the fixture body (A) and unplug the Quick Connect wires.
Surface Mounting
Power Supply Box
Quick
Connect
A
Power Supply Box
A
FF
DD
AA
CC
BB
A
A
CC
6 Attaching the chain to the ceiling
□Hang the fixture body by placing one chain (CC) over each hook (not included) that has been installed on the ceiling.
□Adjust the chains to level the light. The fixture must hang at least 3 in. from the ceiling.
□Feed the wiring through an appropriate conduit based on local electrical code.
CAUTION: Check local electrical code to determine the appropriate type of conduit for the wiring. Do not leave the wiring exposed.

8 9 ETiSSL.com
Please contact 1-855-384-7754 for further assistance.
Surface Mounting (continued)
2 Preparing the power supply box for mounting
□Remove the knock-out near the end of the power supply box.
□Attach one hook from each of the two cable sets (BB) to the hanging holes on the power supply box.
□Close the open hooks attached to the power supply box with pliers. Do not close the open S-hooks at the bottoms of the
cable sets.
Knock-out
Hole
BB
3 Attaching the cover plate
□Feed the electrical wires from the electrical box through the cover
plate (AA).
□Secure the cover plate (AA) to the electrical box with the electrical
box screws (DD), but do not tighten them fully. Screw them into
the cover plate (AA) until there is about 3/8 in. between the cover
plate (AA) and the underside of the screw head.
Power Supply Box
Power Supply Box
Hanging Holes
Hanging
Holes
AA
DD
4 Mounting the power supply box
□Pull the electrical wires from the electrical box through the knock-out hole in the power supply box.
□Align the large ends of the keyholes in the power supply box with the mounting screws (DD), allowing the heads of the screws
(DD) to come through the large ends of the keyholes.
□Rotate the power supply box until the heads of the mounting screws (DD) slide into the narrow ends of the keyholes.
□Tighten the mounting screws (DD) to secure the power supply box to the cover plate (AA) and electrical box.
DD
AA
Power Supply Box
Power Supply Box
5 Attaching the fixture body to the power supply box
□Attach the open hooks on the ends of the cable sets (BB) to the hanging holes on the fixture body (A).
□Close the hook openings with pliers.
□Connect the two ends of the Quick Connect wires.
A
BB
Quick
Connect
Surface Mounting (continued)
Keyholes

10 11 ETiSSL.com
Please contact 1-855-384-7754 for further assistance.
Surface Mounting (continued)
6 Making the electrical connections
□Connect the hot and neutral (black and white) wires from
the power supply box to the same color wires from the
electrical box.
□Connect the green wire from the power supply box to the
grounding wire from the electrical box.
□If 0-10v dimming circuit is available, connect the purple and
gray wires from the power supply box to the same color
wires from the electrical box.
□If dimming is not desired, wrap the ends of the purple and
gray wires with electrical tape to cover the wire.
□Cover the wire connections using the wire connectors (EE).
□Wrap the wire connectors (EE) with electrical tape for a
more secure connection.
Power Supply Box
EE
BB
A
7 Reattaching the fixture body to
the power supply box
□Position the wires back inside the power supply box.
□Align the screw holes in the fixture body (A) with the
screw holes in the power supply box, making sure all
wiring is thoroughly tucked inside the power supply box.
□Fasten the fixture body (A) to the power supply box with
the previously removed screws, using the power tool hex
bit (FF).
A
Power Supply Box
FF
8 Restoring power
□Restore power at the electrical panel.
□Turn on the light switch to activate the fixture.
Downrod Mounting
1 Removing the power supply box
□Remove the four screws that attach the power supply box to the LED fixture body (A) using the power tool hex bit (FF).
□Put the screws aside as they will be needed to reattach the power supply box to the fixture body (A) in a later step.
□Lift the power supply box from the fixture body (A) and unplug the Quick Connect wires.
2 Preparing the power supply box for mounting
□Remove the center knock-out on the power supply box.
□Attach one hook from each of the two cable sets (BB) to the hanging holes on the power supply box.
□Close the open hooks attached to the power supply box with pliers. Do not close the open S hooks at the bottoms of the
cable sets.
Quick
Connect
Power Supply Box
A
A
Power Supply Box
Center Knock-out Hole
BB
Power Supply Box
Power Supply Box
Hanging Holes
Hanging
Holes
FF

12 13 ETiSSL.com
Please contact 1-855-384-7754 for further assistance.
Downrod Mounting (continued)
3 Mounting the power supply box
□Attach the rigid pipe (not included) to the ceiling and pull
the wiring from the electrical box through the pipe.
□Place the pipe through the center knock-out hole in the
power supply box and secure it with the appropriately
sized hardware (not included).
4 Attaching the fixture body to the power supply box
□Attach the open hooks on the ends of the cable sets (BB) to the hanging holes on the fixture body (A).
□Close the hook openings with pliers.
□Connect the two ends of the Quick Connect wires.
Quick
Connect
BB
BB
Power Supply
Box
A
Power
Supply Box
Rigid Pipe 5 Making the electrical connections
□Connect the hot and neutral (black and white) wires from
the power supply box to the same color wires from the
electrical box.
□Connect the green wire from the power supply box to the
grounding wire from the electrical box.
□If 0-10v dimming circuit is available, connect the purple
and gray wires from the power supply box to the same
color wires from the electrical box.
□If dimming is not desired, wrap the ends of the purple and
gray wires with electrical tape to cover the wire.
□Cover the wire connections using the wire connectors (EE).
□Wrap the wire connectors (EE) with electrical tape for a
more secure connection.
□Position the wires back inside the power supply box.
6 Reattaching the power supply box to the fixture body
□Align the screw holes in the fixture body (A) with the screw holes in the power supply box, making sure all wiring is thoroughly
tucked inside the power supply box.
□Fasten the fixture body (A) to the power supply box with the previously removed screws, using the power tool hex bit (FF).
7 Restoring power
□Restore power at the electrical panel.
□Turn on the light switch to activate the fixture.
Downrod Mounting (continued)
Power Supply Box
EE
BB
A
A
Power Supply Box BB
A
FF

14 15 ETiSSL.com
Please contact 1-855-384-7754 for further assistance.
Care and Cleaning
CAUTION: Before attempting to clean fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from
the fuse box.
□Clean the fixture with a soft, dry cloth.
□Do not use cleaners with chemicals, solvents, or harsh abrasives.
□Do not use liquid cleaner on the LEDs, LED driver, or wiring inside the light fixture.
Troubleshooting
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.
Minor problems often can be fixed without the help of an electrician.
Problem Possible Cause Solution
The fixture will not light. The power is off. Ensure the power supply is on.
The circuit breaker is off. Ensure the circuit breaker is in the on position.
There is a bad connection. Check to ensure proper wire connections are made.
Contact a qualified electrician.
There is a defective switch. Contact a qualified electrician.
The fuse blows or the circuit breaker
trips when the light is turned on. The wires are crossed or the power
wire is grounding out.
Check the wire connections.
Contact a qualified electrician or call Commercial
Electric customer service 1-877-527-0313.
Notes

16
GUIDE D’UTILISATION ET D’ENTRETIEN
LAMPE LINÉAIRE À DEL DE 61 CM POUR PLAFOND ÉLEVÉ
Questions, difficultés, pièces manquantes?
Téléphonez au service à la clientèle de ETiSSL
8 h - 17 h, HNC, du lundi au vendredi.
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
MERCI
Nous apprécions la confiance que vous avez accordé à la ETi en achetant ce luminaire à DEL.
Consultez notre gamme complète de produits. Nous vous remercions d’avoir choisi ETi!
Questions, problems, missing parts?
Call ETiSSL Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
Retain this manual for future use.
Partie # HB-171-850-MV-D
Modèle n° 50232162

18 19 ETiSSL.com
Si vous avez besoin d’aide, composez le 1-855-384-7754.
AVIS : Ce dispositif a été testé et se trouve en deça des limites pour un dispositif
numérique de Classe B aux termes de la section 15B des règlements de la FCC. Ces
limites servent à offrir une protection raisonnable contre une interference nocive dans une
installation résidentielle.
Ce dispositif génère, utilise et peut irradier une énergie de fréquence radio; s’il n’est pas
installé et utilisé conformément aux directives, il peut causer une interférence nocive aux
communications radio. Il n’est toutefois pas garanti qu’aucune interférence ne surviendra
dans une installation particulière. Si le dispositif cause une interférence nuisible à la
réception radio ou télé, ce qui peut être établi en éteignant et rallumant le dispositif, on
conseille à l’utilisateur de tenter de remédier à la situation en utilisant une ou plusieurs de
ces procédures :
□Réorienter ou déplacer l’antenne réceptrice.
□Augmenter la distance entre le dispositif et le poste récepteur.
□Brancher l’équipement dans une prise de courant sur un circuit autre que celui sur
lequel le récepteur est branché.
□Demander conseil auprès du marchand ou d’un technicien en radio/télé.
AVERTISSEMENT : Tout changement ou toute modification non
expressément approuvée par la partie responsable de la conformité peut rendre
nulle l’autorisation de l’utilisateur d’utiliser l’équipement.
Table des matières
Table des matières .................................18
Consignes de sécurité ..............................18
Garantie..........................................18
Avant l’installation .................................18
Planification de l’installation ........................18
Outils requis.....................................18
Contenu de l’emballage............................18
Quincaillerie fournie...............................19
Installation .......................................19
Montage en suspension............................19
Montage en surface...............................23
Montage sur barrette..............................27
Entretien et nettoyage ..............................30
Guide de dépannage................................30
Consignes de sécurité
AVERTISSEMENT : Lisez et comprenez
bien les renseignements fournis dans ce
manuel avant de procéder à l’assemblage
et à l’installation. Un manque à le faire
pourrait mener à un risque de choc électrique,
d’incendie ou de blessures qui pourraient être
graves, voire même mortelles.
AVERTISSEMENT : Assurez-vous de
couper le courant au circuit sur lequel vous
travaillerez. Enlevez le fusible ou coupez le
disjoncteur.
Garantie
Ce produit est garanti contre les vices de matière et de fabrication pour une période de 5 ans à compter de la date d’achat originale. Si le
produit ne fonctionne pas à cause d’unvice de matière ou de fabrication dans les 60 mois suivant son achat, consultez www.ETiSSL.com
pour de plus amples renseignements. Le produit sera réparé ou remplacé, à la discrétion d’ETi. Cette garantie est expressément limitée à
la réparation ou au remplacement du produit et toute responsabilité quant aux dommages directs, indirects ou fortuits est expressément
exclue. Certaines provinces ne permettent pas l’exclusion des dommages directs, indirects ou fortuits et la restriction ci-haut peut ne pas
s’appliquer dans votre cas. Cette garantie accorde au consommateur des droits particuliers qui peuvent varier d’une province à l’autre.
LA GARANTIE EST NULLE ET SANS EFFET SI LE PRODUIT EST UTILISÉ À DES FINS AUTRES QUE CELLES PRÉVUES POUR LE PRODUIT.
CONTENU DE L’EMBALLAGE
Pièce Désignation Quantité
A Corps de lampe 1
A
Avant l’installation
PLANIFICATION DE L’INSTALLATION
Avant de commencer à assembler ou installer l’article, assurez-vous d’avoir toutes les pièces. Comparez le contenu de l’emballage avec la
nomenclature. S’il y a des pièces manquantes ou endommagées, ne tentez pas d’assembler, d’installer, ni d’utiliser l’article. Communiquez
avec le service à la clientèle pour obtenir des pièces de rechange.
NOTE : Gardez votre facture ainsi que ces instructions comme preuves d’achat.
Si vous n’êtes pas familier avec les installations électriques, nous recommandons que l’installation soit faite par un électricien qualifié.
OUTILS REQUIS
Pince à
dénuder
Lunettes
de sécurité Échelle Gants
Pinces
Tournevis
à pointe
cruciforme
Perceuse
électrique avec
mèche
Coupe-fil
Vis à
crochet*
Rondelle
encliquable
1,2 cm*
Barrette**
* Montage en suspension
uniquement
** Montage sur barrette
uniquement
NOTE: On peut aussi utiliser des crochets fermés pour fixer le luminaire au plafond lors du montage en suspension.