EUCHIPS EULP20D-1WMC-0 User manual

100VAC-240VAC
50/60Hz
>83%@230VAC,Full load
≥0.95@230VAC,Full load
Cold start,35A(twidth=20us measured at 50% Ipeak)@230VAC
0.12Amax@230VAC
<0.5W
280*30*21mm（L*W*H）
IP20
-20℃~50℃
-40℃~85℃, 20-90%RH
70℃
EN50515, EN61000-3-2
EN61000-4-2, 3, 4, 5, 6, 8, 11; EN61547
EN61347, GB19510
L-N:500V
I/P-O/P: 3000VAC/1min/5mA
Metal
30,000h@tc:65℃
0.1%-100% Dimming to off
55Vdc
±5%
<3%
>15,000 times
1
350mA/9-45VDC/15.75W
700mA/9-29VDC/20.3W
500mA/9-40VDC/20W
<10%@230VAC, Full load
EULP20D-1WMC-0
Surge
Withstand Voltage
Safety Standards
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI 1.0DALI Standard
EMC Eission
EMC Immunity
tc
Lifetime
Material
Dimming Range
Dimension
Net weight: 230g±5%/PCS; 50PCS/Carton; 12kg±5%/Carton; Carton Size:502*338*149mm(L*W*H)
Packing(weight)
IP Rating
Working Temp.
Storage Temp., Humidity
Dimming Type DALI/Touch DIM
Switch Cycle
3 yearsWarranty Condition
No load output voltage
Efficiency
AC Current(max)
Standby power
Inrush Current(max)
THD(full load)
Current(mA)/Voltage (VDC)
Power(W)
Ripple Current
Channel
Current Tolerance
Voltage
Frequency Range(Hz)
Power Factor
Short circuit
Over Load
Close output，recovers automatically after fault removed
When the output voltage is exceeded, the output current decreases and,
recovers automatically when the load is reduced.
Safety&
EMC
Others
Function
Model
Output
Input
Protection
DALI Constant Current Dimming Driver
Application
Downlight Panel Light Flood Light
Spotlight Ceiling Light Floor LightDecorative Light
Summary
Product Features
· Single channel output, output current level selectable by DIP S.W.
· Meet DALI protocol IEC 62386
· Support Touch DIM function
· Wide input voltage of 100VAC ~ 240VAC
· High efficiency up to 83%
· Built-in active PFC function
· Dimming effect smooth, no flicker
· Protections: Over load, short circuit
· Suitable for indoor LED lighting application, such as down light, panel light,
tri-proof light, and so on
EULP20D-1WMC-0 is a 20W AC/DC constant current mode output LED driver featuring the multiple levels
selectable by DIP switch and complies with DALI standard protocol IEC 62386. EULP20D-1WMC-0 can be
connected to DALI main controller or Touch DIM to achieve a smooth dimming effect.
EULP20D-1WMC-0 (Product No.:102100123101)
1/2
User’s manual: 2019-8 www.euchips.com
Current Selection Table
Remark: Function default setting is: 350mA (@switch are
all OFF state)
Technical Paramaters
350mA 500mA 700mA
9-40V 9-29V9-45V
ON OFF

2/2
User’s manual: 2019-8 www.euchips.com
Dimension(mm)
DALI Wiring
※The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions,
the function of the product shall prevail.Please contact us if you have any questions .
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75-1.5mm²is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire
connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
DALI Constant Current Dimming Driver
Push DIM(Touch DIM) DiagramDALI Diagram
Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.
Push DIM Function
Cautions
1. Press the Push DIM (Touch DIM) switch for 8s or more,the driver can be controlled via Push DIM switch.
2. Short press the Push DIM (Touch DIM) switch (<0.5s) to control the lamp on or off.
3. Long press the Push DIM (Touch DIM) switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Push DIM (Touch DIM) switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long pressing
Push DIM (Touch DIM) switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.
0120 40 60 80 100 120 140 160 180 200 220 240 254
20
40
60
80
100
120
0
110 20 30 40 50
0.1
0.2
0.3
0.4
DALI Dimming Level
Output Current(%)
Dimming Curve
280
30
268.5
21
DA 2
DA 1
N
L
LED-
LED+
L
N
DALI Signal Input
DALI Master
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
L
N
DALI Controller
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
Push DIM Panel(Touch DIM)
LN

100VAC-240VAC
50/60Hz
>83%@230VAC, 满载
≥0.95@230VAC, 满载
冷启动,35A(在50%Ipeak下测twidth=20us)@230VACC
0.12Amax@230VAC
<0.5W
280*30*21mm（长*宽*高）
IP20
-20℃~50℃
-40℃~85℃, 20-90%RH
70℃
EN50515, EN61000-3-2
EN61000-4-2, 3, 4, 5, 6, 8, 11; EN61547
EN61347, GB19510
L-N:500V
I/P-O/P: 3000VAC/1min/5mA
金属
30,000小时@tc:70℃
0.1%-100% 变暗直至关闭
50V Max
±5%
<3%
>15,000次
1
<10%@230VAC, 满载
EULP20D-1WMC-0
浪涌
耐压标准
安全标准
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-2070: 2009, DALI 1.0DALI 标准
电磁兼容
EMC抗扰度
tc
寿命
材质
调光范围
尺寸
包装尺寸(重量)
防水等级
工作温度
储存温度、湿度
调光方式
开关周期
3年质保
空载输出电压
效率
电流
待机功耗
浪涌电流
THD
电流/电压/功率
波纹电流
通道
电流公差
电压
频率
功率因素
过载
短路 关断输出，移除故障后自恢复
超过输出电压范围时，输出电流下降，减轻负载后自动恢复。
安全
&
电磁
兼容
其它
功能
型号
输出
输入
保护
DALI恒流调光驱动器
应用
筒灯 面板灯 投光灯
射灯 吸顶灯 落地灯装饰灯
概述
产品特点
单通道恒流输出，多级电流可选
遵循DALI协议标准 IEC62386
支持Touch DIM功能
宽电压输入：100VAC~240VAC
内建主动式PFC功能
过载保护，短路保护，
适用于LED室内灯具,比如筒灯，面板灯，三防灯等
1/2
用户手册: 2019-8 www.euchips.cn
电流选择表
备注：出厂默认设置电流为350mA(1,2在OFF状态)
技术参数
350mA 500mA 700mA
9-40V 9-29V9-45V
ON OFF
净重: 230g±5%/PCS; 50PCS/Carton; 12kg±5%/箱; 外箱尺寸:502*338*149cm(长*宽*高)
EULP20D-1WMC-0一款20W交流变直流LED驱动器，输出电流可
以通过DIP开关选择，符合DALI标准协议IEC62386。连接DALI主
控或Touch DIM可以实现平滑的调光效果。
350mA/9-45VDC/15.75W
700mA/9-29VDC/20.3W
500mA/9-40VDC/20W
DALI/Touch DIM
EULP20D-1WMC-0 (产品代码.:102100123101)

DALI恒流调光驱动器
2/2
用户手册: 2019-8 www.euchips.cn
尺寸(mm)
接线图
※ 本说明书内容如有更新，恕不另行通知。若您使用的产品功能与说明书不一致时，请以产品为准。如有疑问请与我们联系。
调光曲线
注意事项:
1、本产品请由具有专业资格的人员进行调试安装。
2、本产品不能防水，需避免日晒雨淋，如安装在户外，请用防水箱。
3、良好的散热条件会延长产品的使用寿命，请把产品安装在通风良好的环境。
4、请检查使用的LED电源输出电压电流，是否符合产品要求。
5、出于安全考虑，推荐输入和输出（信号端除外）用0.75-1.5mm² PVC或橡胶线缆，并确保接线牢固，以免电线过热或接触不良触发事故。扁平电源线不适用。
6、通电调试前，应确保所有接线正确，以避免因接线错误而导致灯具损坏。
7、如果发生故障，请勿私自维修；如果有疑问，请联系供应商。
0120 40 60 80 100 120 140 160 180 200 220 240 254
20
40
60
80
100
120
0
110 20 30 40 50
0.1
0.2
0.3
0.4
DALI Dimming Level
Output Current(%)
Push DIM 功能
1.长按Push DIM(Touch DIM)开关8s，进入Push DIM (Touch DIM)模式。
2.短按Push DIM (Touch DIM)开关 (<0.5秒) 进行灯的亮暗控制。
3.长按Push DIM (Touch DIM)开关 (>0.5秒) 进行灯具的亮度调节，光是调亮还是调暗，随着每次按压的开关变化而变换。
4.双击Push DIM (Touch DIM)开关（<0.3秒），连接的所有灯具将达到最亮状态。
5.亮度调节范围为1%-100%。
6.具有断电记忆功能，重新上电将恢复到上一次断电的状态。
DALI应用图 Push DIM (Touch DIM)应用图
280
30
268.5
21
DA 2
DA 1
N
L
LED-
LED+
L
N
DALI 信号输入
DALI 主控
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
L
N
DALI 控制器
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
Push DIM Panel(Touch DIM)
LN
备注: 只能使用开路的按压式开关(不带指示灯). 采用同步连线时每个设备和设备之间的线长不超过20米.