EUCHIPS EUP150AD-1H24V-0 User manual

220VAC-240VAC
50/60Hz
>90%@230VAC,Full load
>0.95@115VAC,Full load
Cold start,27A(twidth=650us measured at 50% Ipeak) @230VAC
0.8Amax@230VAC
310*60*45mm（L*W*H）IP20
-20˫~50˫-40˫~85˫, 20-90%RH
90˫EN50515, EN61000-3-2
EN61000-4-2, 3, 4, 5, 6, 8, 11; EN61547
EN61347, GB19510
L-N:1KV
I/P-O/P: 3000VAC/1min/5mA
Metal
50,000h@tc:80˫0.1%-100% Dimming to off
±3%
400mVp-p
DALI / Touch DIM/ 0/1-10V/ Adjustable resistance / PWM
>100,000 times
1
6.25A/24VDC/150W
<10%@230VAC, Full load
EUP150AD-1H24V-0
Surge
Withstand Voltage
Safety Standards
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI 1.0DALI Standard
EMC Eission
EMC Immunity
tc
Lifetime
Material
Dimming Range
Dimension
Net weight: 860g±5%/PCS; 10PCS/Carton;9.1kg±5%/Carton; Carton Size: 333*268*150mm(L*W*H)
Packing(weight)
IP Rating
Working Temp.
Storage Temp., Humidity
Dimming Type
Switch Cycle
5 yearsWarranty Condition
Efficiency
AC Current(max)
Inrush Current(max)
THD(full load)
Current / Voltage / Power
R & N (Max)
Channel
Voltage Accuracy
Voltage
Frequency Range(Hz)
Power Factor
Short circuit
Over temperature
Over load Limit the output power to 100% to 150%
Close the output, restart to recover since fault condition is removed for 10s
Shut down the output, recovers auto matically when temp.b ack to normal.
Safety&
EMC
Others
Function
Model
Output
Input
Protection
DALI&0/1-10V Constant Voltage Dimming Driver
Summary
Product Features
· Single channel constant voltage output
· Support a variety of dimming mode（DALI / 0/1-10V active signal / adjustable resistance / PWM / Touch DIM）· High range of input voltage 220VAC ~ 240VAC
· Built-in active PFC function
· Dimming effect smooth, no flicker
· Over load protection; Over temperature protection; Short circuit protection
· Suitable for indoor LED lighting application, such as LED strips, spot light, wall
washer,and so on
EUP150AD-1H24V-0 is a constant voltage mode output LED driver. This driver complies with DALI standard
protocol IEC 62386,and provides multiple dimming function (DALI , 0/1-10V active signal ,PWM, adjustable resistance,
and Touch DIM) to achieve a smooth dimming effect.
EUP150AD-1H24V-0 (Product No.:100200030101)
1/2
User’s manual: 2019-9 www.euchips.com
Dimension(mm)
Technical Paramaters
310
4.2
60 45.3
300
45
Application
Wall Washer LED Strip Light LED Tube Underground Light AR111 Venture Light

DALI&0/1-10V Constant Voltage Dimming Driver
2/2
User’s manual: 2019-9 www.euchips.com
DALI Wiring
※ The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions,
the function of the product shall prevail.Please contact us if you have any questions .
Cautions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75- 2.5mm² is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire
connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
Push DIM(Touch DIM) DiagramDALI Diagram
Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.
Push DIM Function
1. Press the Push DIM (Touch DIM) switch for 8s or more,the driver can be controlled via Push DIM switch.
2. Short press the Push DIM (Touch DIM) switch (<0.5s) to control the lamp on or off.
3. Long press the Push DIM (Touch DIM) switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Push DIM (Touch DIM) switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long pressing
Push DIM (Touch DIM) switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.
Dimming Curve
DALI MASTER
N
L
0/1-10V Signal Input
N
L
DALI Curve 0/1-10V Curve
01 20 40 60 80 100 120 140 160 180 200 220 240 254
20
40
60
80
100
120
0
1 10 20 30 40 50
0.1
0.2
0.3
0.4
DALI Dimming Level
Output Current(%)
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
Push DIM Panel(Touch DIM)
LN
861 861 861
12V/24V
861 861 861
12V/24V
861 861 861
12V/24V
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
L
N
DALI Controller
861 861 861
12V/24V
861 861 861
12V/24V
861 861 861
12V/24V
100
80
60
40
20
0
0
5
9
14
18
23
27
32
36
41
45
50
54
59
63
68
72
77
81
86 90
95
99
Input Signal(%)
Output Voltage(%)