eufy Security 906290 User manual

Anker Innovations Limited.All rights reserved. eufy Security and eufy
Security Logo are trademarks of Anker Innovations Limited, registered in the
United States and other countries.All other trademarks are the property of
their respective owners.
51005003046 V01

QUICK START GUIDE
eufy Security Video Doorbell Dual (Battery)
KURZANLEITUNG
GUÍA DE INICIO RÁPIDO
GUIDE DE DÉMARRAGE RAPIDE
GUIDA RAPIDA
SNELSTARTGIDS
GUIA DE INÍCIO RÁPIDO


English 01
Deutsch 29
Español 57
Français 85
Italiano 113
Nederlands 141
Portuguese 169
 197

EN 1
INCLUDED
WHAT’S
1
For Video Doorbell Installation
QSG
eufy SecurityVideo
Doorbell Dual (Battery)
Model:T8213
Screw Pack
Screw Hole
Positioning Card
micro-USB
charging cable
15° Mounting
Wedge (Optional)
Mounting Bracket
Extension Wires
and Wire Nuts
(Optional)
Detaching
Pin Quick
Start Guide

2 EN
For HomeBase 2 Installation
HomeBase 2
Model:T8010X
Power Adapter for
HomeBase 2
Ethernet Cable for
HomeBase 2
Note: Power plug may vary in different regions.

EN 3
OVERVIEW
PRODUCT
2
Video Doorbell
Front View:
5
3
2
1
6
4
7
1.Motion Sensor
2.Microphone
3.Primary Camera Lens
4.Ambient Light Sensor
5.LED Ring / Doorbell Button
6.Secondary Camera Lens
7.Speaker
Rear View:
2
3
4
11.Detaching Mechanism
2.Micro USB Charging Port
3.SYNC/RESET Button
4.Power Terminals for Existing
Doorbell Wires (Optional)

4 EN
Operation How-to
Power on the doorbell Press the SYNC button.
Add doorbell to HomeBase Press and hold the SYNC button until you hear a beep.
Power off the doorbell Quick-press the SYNC button 5 times in 3 seconds.
Reset the doorbell Press and hold the SYNC button for 10 seconds.
HomeBase 2
23
4 5 6
7
1
1. Status LED
2. Speaker
3. Power Port
4. USB Port
5. Ethernet Port
6. SYNC/ALARM OFF Button
7. Reset Button

EN 5
THE SYSTEM WORKS
HOW
3
How the System Works
The video doorbell system includes 2 parts. One is the video doorbell at your
door.The other is the HomeBase in your house.
The video doorbell detects motion at your porch and allows you to answer the
door anytime and anywhere. The HomeBase stores video clips on its built-in
storage. When someone rings the doorbell, people in the house will be notied.
Doorbell Chime
Video Doorbell Dual
(Battery)

6 EN
CONNECTING THE HOMEBASE
STEP 1
4
Connect HomeBase 2 to the Internet
1. Power on the HomeBase 2, then use the ethernet cable provided to
connect the HomeBase 2 to your home router.
2. The LED indicator turns blue (this may take up to 1min) when HomeBase
2 is ready for setup.

EN 7
SETTING UP THE SYSTEM
STEP 2
5
Download the App and Set up the System
Download the eufy Security app from the App Store (iOS devices) or Google
Play (Android devices).
Sign up for a eufy Security account, then follow the onscreen instructions to
complete the setup.

8 EN
DETERMINING THE POWER OPTION
STEP 3
6
Option 1 - Battery Powered
1. If you don’t have existing doorbell wiring at the front door, use the built-in
battery.You are free to determine the doorbell position and the mounting
is easy and quick.
2. When the doorbell battery level is low, you need to detach and charge it.
3. If you choose this option, please jump to STEP 4 FINDING A
MOUNTING SPOT.
6 months
Note: The battery life varies depending on usage. In most common cases,
a doorbell may have up to 10 events per day and each recording lasts 20
seconds on average. Under this scenario, the doorbell battery life can last up
to 6 months.

EN 9
Option 2 - Doorbell Wire Powered
1. If you have existing and working doorbell wiring at the front door, the
doorbell will be powered by the wires constantly. So you don’t need to
detach and charge it after installation.
2. Since the doorbell is connected to the wires, the mounting position is
limited.
3. If you choose this option, please jump to APPENDIX 3 POWERING THE
DOORBELL WITH EXISTING DOORBELL WIRES.
8 - 24V AC Doorbell Wiring

10 EN
FINDING A MOUNTING SPOT
STEP 4
7
Find a Mounting Spot
Take the video doorbell to your front door and check the live view on the app
at the same time. Find a location where you can see the desired eld of view.
Consider the following factors:
1. Check if you can reuse the existing holes and anchors on the wall or door
frame.
2. If you want to place the doorbell close to a side wall, make sure the wall
doesn’t show up in the eld of view. Otherwise IR light will be reected and
night vision will become blurry.
3. If you are drilling the mounting holes for the rst time, the recommended
mounting height is 48" / 1.2 m from the ground.
4. To adjust the angel, use the 15° mounting wedge as a supplementary
mounting bracket.
1.76m(5’9”)
1.2m (48")
0.3m
(12")
1m
(40")
15°
Without 15° Mounting wedge With 15° Mounting wedge
Door Door Video Doorbell Video Doorbell

EN 11
Place the screw hole positioning card against the wall to mark the position.

12 EN
MOUNTING THE BRACKET
STEP 5
8
Mount the Doorbell on a Wooden Surface
If you’re mounting the doorbell on a wooden surface, you don’t need to pre-
drill pilot holes. Use the provided screws to secure the mounting bracket on
the wall, the screw hole positioning card indicates the position of the screw
holes.
What you need: Screwdriver, Mounting Bracket, 15° Mounting Wedge
(Optional), Screw Packs
Phillips-Head Screwdriver
(not provided)
Wall
Wall
Mounting
Bracket
Mounting
Wedge
Mounting
Bracket
Mounting Bracket
(Attached to 15° Mounting
Wedge)
15° Mounting
Wedge (Optional)
Screw Packs (Spare screws
and anchors are included.)
Without 15° Mounting Wedge With 15° Mounting Wedge

EN 13
Mount the Doorbell on Surfaces Made Out of
Hard Materials
1. If you’re mounting the doorbell on a surface made out of hard materials,
like brick, concrete, stucco, drill 2 holes through the screw hold positioning
card with a 15/64”(6mm) drill bit.
2. Insert the provided anchors, and then use the provided long screws to
secure the mounting bracket on the wall.
What you need: Power Drill, 15/64”(6 mm) Drill Bit, Mounting Bracket,
15° Mounting Wedge (Optional), Screw Packs
Power Drill
(not provided)
15/64”(6 mm) Drill
Bit
Mounting Bracket
(Attached to 15°
Mounting Wedge)
15° Mounting
Wedge (Optional)
Screw Packs (Spare screws
and anchors are included.)
1

14 EN
22
Wall
Wall
Mounting
Bracket
Mounting
Wedge Mounting
Bracket
Without 15° Mounting Wedge With 15° Mounting Wedge

EN 15
MOUNTING THE DOORBELL
STEP 6
9
Mount the Doorbell
Align the doorbell on the bottom, and then move it into place on top. Press the
doorbell down until it clicks.
You’re all set!
If you want to detach the doorbell or recharge it, please refer to the following
sections.

16 EN
DETACHING THE DOORBELL
APPENDIX 1
10
Detach the Doorbell
1. Use the doorbell detaching pin provided if you wish to detach the doorbell
from the mounting bracket.
2. Press into the pinhole on top of the doorbell, and then lift the top for
removal.
What you need: Doorbell Detaching Pin
Doorbell
Detaching Pin

EN 17
RECHARGING THE DOORBELL
APPENDIX 2
11
Recharge the Doorbell
LED indicator Charging: Flashing Green
Fully charged: Green
Charging time 6 hours from 0% to 100%