EverFocus ENVR8304D-8CH User manual

ENVR8304D-8CH
8-Channel Plug & Play NVR
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: July, 2013
Notice: This content is subject to be changed without notice.

EVERFOCUS ELECTRONICS CORPORATION
ENVR8304D-8CH
User’s Manual
2013 EverFocus Electronics Corp
www.everfocus.com
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form
or by any means without written permission of the EverFocus Electronics Corporation.
Release Date: July, 2013
QuickTime is a registered trademark of the Apple Computer, Inc.
Windows is a registered trademark of the Microsoft Corporation.
Linksys is a registered trademark of the Linksys Corporation.
D-Link is a registered trademark of the D-Link Corporation.
DynDNS is a registered trademark of the DynDNS.org Corporation.
Other product and company names mentioned herein may be the trademarks of their respective owners.

ii
Safety Precautions
Refer all work related to the installation of this product to qualified service personnel or
system installers.
Do not block the ventilation openings or slots on the cover.
Do not drop metallic parts through slots. This could permanently damage the appliance.
Turn the power off immediately and contact qualified service personnel for service.
Do not attempt to disassemble the appliance. To prevent electric shock, do not remove
screws or covers. There are no user-serviceable parts inside. Contact qualified service
personnel for maintenance. Handle the appliance with care. Do not strike or shake, as this
may damage the appliance.
Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do
take immediate action if the appliance becomes wet. Turn the power off and refer servicing
to qualified service personnel. Moisture may damage the appliance and also may cause
electric shock.
Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth
to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild
detergent and wipe gently.
Do not overload outlets and extension cords as this may result in a risk of fire or electric
shock.
Do not operate the appliance beyond its specified temperature, humidity or power source
ratings. Do not use the appliance in an extreme environment where high temperature or
high humidity exists. Use the NVR at temperatures within 0°C~40°C / 32°F~104°F (Storage).
The input power source is 100-240 VAC~ / 150W max.
Read Instructions
All the safety and operating instructions should be read before the unit is operated.
Retain Instructions
The safety and operating instructions should be retained for future reference.
Heed Warnings
All warnings on the unit and in the operating instructions should be adhered to.

iii
Follow Instructions
All operating and use instructions should be followed.
Cleaning
Unplug the unit from the outlet before cleaning. Do not use liquid cleaners, abrasive or
aerosol cleaners. Use a damp cloth for cleaning
Attachments
Do not use attachments not recommended by the product manufacturer as they may
cause hazards.
Water and Moisture
Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, near a swimming pool, in an unprotected outdoor
installation, or any area which is classified as a wet location.
Servicing
Do not attempt to service this unit by yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them, playing particular attention to cords and plugs,
convenience receptacles, and the point where they exit from the appliance.
Object and Liquid Entry
Never push objects of any kind into this unit through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the unit.
Battery
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
a. Use only two AAA dry cell batteries.
b. Do not dispose of the batteries in a fire as it may explode.
ATTENTION! This is a class A product which may cause radio interference in a
domestic environment; in this case, the user may be urged to take adequate measures.

iv
This Product is RoHS compliant.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the users’ authority to operate this equipment.
WEEE
The information in this manual was current upon publication. The manufacturer reserves the right
to revise and improve his products. Therefore, all specifications are subject to change without prior
notice. Manufacturer is not responsible for misprints or typographical errors.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for
later reference.
Your EverFocus product is designed and manufactured with high quality materials and
components which can be recycled and reused. This symbol means that electrical and
electronic equipment, at their end-of-life, should be disposed of separately from your
household waste. Please, dispose of this equipment at your local community waste
collection/recycling centre. In the European Union there are separate collection systems
for used electrical and electronic product.
Please, help us to conserve the environment we live in!
This product complies with the High-Definition Multimedia Interface (HDMI)
Specification Adopter Agreement.

v
TABLE OF CONTENTS
1. Introduction.......................................................................................................................1
1.1 Overview ....................................................................................................................2
1.2 Features .....................................................................................................................3
1.3 Packing List .................................................................................................................4
1.4 Optional Accessories...................................................................................................5
1.5 Front Panel .................................................................................................................6
1.6 Rear Panel ..................................................................................................................7
2. Installation.........................................................................................................................8
2.1 Hard Disk Drive Installation.........................................................................................8
2.1.1 Hard Disk Compatibility List............................................................................10
2.2 Rack Mount ..............................................................................................................10
2.3 Basic Connection ......................................................................................................11
2.3.1 Camera Connection........................................................................................12
2.3.2 Cable Length Extension ..................................................................................13
2.3.3 Monitor Connection .......................................................................................14
2.3.4 Display Aspect Ratio .......................................................................................15
2.3.5 Alarm I/O .......................................................................................................16
2.3.6 RS-485 Port ....................................................................................................17
2.3.7 RS-232 Port ....................................................................................................17
2.4 Turning On / Off the Power.......................................................................................17
2.5 Connecting the NVR to the Network .........................................................................18
2.5.1 Router or LAN Connection ..............................................................................18
2.5.2 Direct High-Speed Connection........................................................................21
2.5.3 One-to-One Connection .................................................................................22
2.6 Checking the Dynamic IP Address .............................................................................26
3. General Operation ...........................................................................................................29
3.1 Login.........................................................................................................................29
3.2 Opening OSD Root Menu ..........................................................................................30
3.3 Field Input Option.....................................................................................................30
3.4 Camera Selection......................................................................................................31
3.5 Enabling Audio..........................................................................................................32
4. OSD Root Menu ...............................................................................................................33
4.1 PTZ ...........................................................................................................................35
4.1.1 Express Control of PTZ....................................................................................37
4.2 Layout Switching.......................................................................................................38

vi
4.3 Channel Switching ....................................................................................................38
4.4 Display......................................................................................................................39
4.5 Sequence ..................................................................................................................40
4.6 Zoom ........................................................................................................................40
4.7 Archiving the Recordings or Log Data to the USB ......................................................42
4.8 Logout ......................................................................................................................43
5. Search and Playback ........................................................................................................44
5.1 Quick Playback..........................................................................................................44
5.2 Playback Bar .............................................................................................................45
5.3 Searching the Recordings for Playing Back ................................................................47
5.3.1 Time Search....................................................................................................47
5.3.2 Event Search ..................................................................................................48
5.3.3 Snapshot Search.............................................................................................49
5.3.4 POS Search .....................................................................................................51
6. Configuration...................................................................................................................53
6.1 Camera .....................................................................................................................55
6.1.1 Camera Status ................................................................................................55
6.1.2 Basic...............................................................................................................56
6.1.3 PTZ .................................................................................................................58
6.1.4 Tracking..........................................................................................................61
6.1.5 Pattern Tour...................................................................................................63
6.1.6 Adjust.............................................................................................................65
6.2 Record & Playback ....................................................................................................66
6.2.1 Record............................................................................................................66
6.2.2 Quick Archive .................................................................................................67
6.2.3 Playback .........................................................................................................68
6.3 Event ........................................................................................................................69
6.3.1 Alarm .............................................................................................................69
6.3.2 Connection Loss .............................................................................................71
6.3.3 Motion ...........................................................................................................73
6.3.4 Other..............................................................................................................76
6.3.4.1 Fan Failure......................................................................................76
6.3.4.2 Disk Temperature ...........................................................................77
6.3.4.3 Disk Failure .....................................................................................78
6.3.4.4 Disk Full ..........................................................................................79
6.3.4.5 Disk Off...........................................................................................80
6.3.4.6 Power Loss .....................................................................................81
6.3.4.7 Network Loss..................................................................................82
6.4 Disk...........................................................................................................................83
6.4.1 Disk ................................................................................................................83

vii
6.4.2 Lock / Format .................................................................................................84
6.4.3 RAID ...............................................................................................................85
6.5 Display Setting ..........................................................................................................87
6.5.1 Monitor OSD ..................................................................................................87
6.5.2 M/T SEQ .........................................................................................................88
6.6 Network....................................................................................................................89
6.6.1 LAN & WAN....................................................................................................89
6.6.2 Email ..............................................................................................................92
6.6.3 DDNS..............................................................................................................93
6.6.3.1 EverFocus DDNS .............................................................................94
6.6.3.2 www.dyndns.org ............................................................................95
6.6.4 FTP .................................................................................................................96
6.6.5 Alarm Server ..................................................................................................97
6.6.6 Network Test..................................................................................................98
6.7 Schedule ...................................................................................................................99
6.7.1 Express Setup .................................................................................................99
6.7.2 Holidays .......................................................................................................100
6.7.3 Schedule.......................................................................................................101
6.8 System Setting........................................................................................................104
6.8.1 Date/Time ....................................................................................................104
6.8.2 Daylight Saving .............................................................................................105
6.8.3 User Group...................................................................................................106
6.8.4 User Management........................................................................................107
6.8.5 I/O Control ...................................................................................................110
6.8.6 EKB200 Setting .............................................................................................112
6.8.7 Miscellaneous ..............................................................................................114
6.9 System Information ................................................................................................116
6.9.1 Configuration ...............................................................................................116
6.9.2 Log ...............................................................................................................118
7. Remote Access to the NVR ............................................................................................119
7.1 Accessing the NVR ..................................................................................................119
7.2 Install JAVA Runtime...............................................................................................121
7.3 Browser Security Setting.........................................................................................122
7.3.1 Installing ActiveX Controls ............................................................................122
7.3.2 Enabling ActiveX Controls.............................................................................123
7.4 Remote Live View ...................................................................................................126
7.5 Camera ...................................................................................................................129
7.5.1 Camera Status ..............................................................................................129
7.5.2 Basic.............................................................................................................130
7.5.2.1 Camera.........................................................................................130

viii
7.5.2.2 PTZ ...............................................................................................132
7.5.3 Video Adjust.................................................................................................139
7.6 PTZ .........................................................................................................................141
8. Specifications.................................................................................................................143
Appendix A: Network Overview .............................................................................................147
Appendix B: Linksys & D-Link Port Forwarding.......................................................................151
Appendix C: IR Remote Control ..............................................................................................155

ENVR8304D-8CH
1
1. Introduction
EverFocus all new NVR Solution, targeting small-scale installations such as homes and small
businesses, will also be placed under the spotlight. With true plug-and-play setup and real-time
local display up to Full HD resolution, the Linux-embedded solution works just like a NVR but
without the need for those complicated network settings that would be otherwise required
with conventional NVR systems.
Featuring a standalone network video recorder up to 8 channels, along with a series of NVR
EverFocus megapixel cameras, the NVR Solution offers a complete system kit that can be easily
installed in a matter of minutes. There is no need to purchase extra computers or software to
operate the system.
When paired with our powerful EverFocus PowerVideo Plus CMS, the ENVR8304D-8CH can be
used in complex multi-site installations with centralized management. The ENVR8304D-8CH is
also fully supported by the EverFocus MobileFocus remote viewer on iOS and Android devices,
which help extend video surveillance from fixed locations to mobile environments.
Chapter
1

ENVR8304D-8CH
2
1.1 Overview
Mouse
USB Memory Stick
IR Remote Control
Front View
Rear View
Power Cord
eSATA HDD
Expansion
(EDA450)
RS-485
Device
RS-232
Data Input
Line Level
Audio In
Line Level
Audio Out
Alarm In / Out
Main Monitor
(HDMI)
Main Monitor
(VGA)
Web Remote
Client
PowerVideo Plus
(CMS)
NVR Smart Switch
EKB200
Keyborad
IP Cameras 1 ~ 8
Network
Figure 1-1

ENVR8304D-8CH
3
1.2 Features
•8-channel real-time recording and playback at 1080p resolution
•Support megapixel IP cameras
•The Plug and Play design simplifies installation and configuration
•H.264 compression format for enhancing recording capacity and improving network
image transmission speed
•Separately configured HDMI or VGA (1080p) monitor outputs
•High bandwidth 1080p recording (200 / 240fps) with recordable reduced bandwidth
stream for mobile or multiplexed viewing applications
•RAID5 – for full data protection
•Free EverFocus DDNS Service – static IP address is not required for reliable remote access
•Supports one eSATA port for external HDD (optional:EDA450)
•Supports live monitoring and playback of video from mobile devices via MobileFocus /
MobileFocus Plus Apps
•Multiple control inputs: mouse / remote controller / EKB500 and EKB200 keyboards
•Multiple intelligent video query functionality, including snapshot and smart search
•Powerful archive functionality from both remote and NVR sites
•Simplified access to common features such as setup, archival, playback and search
functions through express menus
•Remote configuration support from built-in web interface
•Gigabit Ethernet interface for remote network viewing and control
•8 ports PoE smart switch (NVR Smart Switch)
•Integration with PowerVideo Plus
•Multi-language support
•19” Rack mountable – rack ears included

ENVR8304D-8CH
4
1.3 Packing List
•
ENVR8304D-8CH x 1
•
User Manual x 1
•
CD x 1 (Please see Note 3.)
•
Mouse x 1
•Power Cord x 1
•SATA Cable x 4
•
HDD Bracket x 4
•
Rack Ear x 2
•IR Remote Control x 1
•AAA Battery x 2 (Please see Note 4.)
•
Sliver Screw x 16, Washer Head Screw x 8, M3 (φ6.8) Screw x 4
•NVR Smart Switch x 1, Power Cord x 1, CD x 1 (Please see Note 5.)
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your
local EverFocus office or agents for more information. Please also keep the shipping
carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
3. The CD contains the IP Utility software, User Manual and Quick Installation Guide.
4. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
a. Use only two AAA dry cell batteries.
b. Do not dispose of the batteries in a fire as it may explode.
5. These three items are packed in a box, and the CD contains the User Manual of the NVR
Smart Switch.

ENVR8304D-8CH
5
1.4 Optional Accessories
•
EKB200 (USB controller keyboard: connect to the PC to control the PTZ cameras
connected to the NVR). Please refer to 6.8.6 EKB200 Setting and the User Manual of
the EKB200 Keyboard.
•
EKB500 (RS-485 keyboard: connect to the RS-485 port to control the PTZ cameras
connected to the NVR). Please refer to 6.1 Camera and the User Manual of the EKB500
Keyboard.
•
EDA450 (eSATA Storage Device: connect to the eSATA port of the ENVR8304D-8CH).
Please refer to No. 2, Figure 1-3.

ENVR8304D-8CH
6
1.5 Front Panel
51 6 7 8
2 3 4
Figure 1-2
No. Name Description
1 Power Indicates the power is on.
2 REC Indicates the NVR is recording.
3 LAN Indicates the NVR is connected to the network.
4 Alarm Indicates an alarm input is triggered.
5 HDD1~4 Separately indicates the internal HDD 1~4 is activating.
6 eSATA Indicates the external HDD is activating.
7 IR Receiver Receiver for signals from the IR remote control.
8 USB1 / USB2 USB2.0 ports for connecting to a mouse, external storage device,
or EKB200 keyboard.

ENVR8304D-8CH
7
1.6 Rear Panel
12345
678910 11 13 14
12
Figure 1-3
No. Name Description
1 Power Press to turn On / Off the NVR.
2 eSATA Port Connects to an external eSATA storage device. (EDA450)
3 USB3 / USB4 The USB2.0 ports for connecting to a mouse, external storage
device or EKB200 keyboard.
4 Audio Input Connects to the audio input devices.
5 Audio Output Connects to the audio output devices, such as speakers. Note that
the speakers with amplifier are required.
6 Power Port
Connects to the 100-240 VAC~ power using the supplied Power
Cord.
7 RS-232 Port Connects to the RS-232 device. Please refer to 2.3.7 RS-232 Port.
8 RS-485 Port
Connects to the RS-485 device, such as EverFocus’ EKB-500
keyboard. Please refer to 2.3.6 RS-485 Port.
9 HDMI Port
Connects to the Main monitor using a HDMI cable. Please refer to
2.3.3 Monitor Connection.
10 VGA Port
Connects to the Main monitor using a VGA cable. Please refer to
2.3.3 Monitor Connection.
11 WLAN
Connects to the network using a standard RJ-45 CAT5 10/100Mb
Ethernet cable. Please refer to 2.5 Connecting the NVR to the
Network.
12 LAN Connects to a PoE device using a standard RJ-45 CAT5 10/100Mb
Ethernet cable. Please refer to 2.3.1 Camera Connection.
13 Alarm Input Connects up to 2 alarm inputs. Please refer to 2.3.5 Alarm IO.
14 Alarm Output Connects to 2 alarm output devices. Please refer to 2.3.5 Alarm IO.

ENVR8304D-8CH
8
2. Installation
2.1 Hard Disk Drive Installation
1. Make sure the NVR is power-off.
2. Unscrew the ten housing screws on the NVR, and open the housing.
Figure 2-1
3. Screw two HDD brackets on both sides of the HDDs using the Sliver Screws.
Silver Screw
HDD Bracket
Figure 2-2
4. Use the SATA Cable, and connect one end to the SATA port on the small PCB inside the
NVR, and the other end to the SATA port on the HDD.
Figure 2-3
Chapter
2

ENVR8304D-8CH
9
5. Connect the internal power cable to the HDD.
Figure 2-4
Note: The internal power cable is connected to the Main board inside the NVR. The power
cable features two connectors, which can be used to connect to two HDDs.
6. Screw the HDDs with the brackets inside the NVR using the Washer Head Screws.
Figure 2-5
7. Screw back the housing to the NVR.

ENVR8304D-8CH
10
2.1.1 Hard Disk Compatibility List
Please use the hard disk models recommended in the list below to ensure your hard disks will
be compatible.
SATA Hard Disk
Model
Capacity
Seagate
SV35.5 SATA2 / ST3500410SV
500GB
SV35.5 SATA2 / ST31000525SV 1TB
SV35.5 SATA3 / ST3500411SV
500GB
SV35.5 SATA3 / ST31000526SV
1TB
SV35 SATA3 / ST2000VX002
2TB
Barracuda SATA3 / ST500DM002
500GB
Barracuda SATA3 / ST1000DM003
1TB
Western Digital
WD10EVDS SATA2
1TB
WD10EURS SATA2
1TB
WD20EVDS SATA2
2TB
WD20EURS SATA2
2TB
WD1600AVVS SATA
160GB
WD3200AVVS SATA
320GB
WD5000AVVS SATA
500GB
WD7500AVVS SATA
750GB
WD10EVVS SATA
1TB
Note: If using two or more hard disks, please choose the hard disks with the same capacity.
2.2 Rack Mount
To install rack ears on the NVR, use the supplied two Rack Ears and the four M3 (φ6.8) Screws
for rack mount installation on both side.
Figure 2-6

ENVR8304D-8CH
11
2.3 Basic Connection
The instructions below describe the basic connection for ENVR8304D-8CH
Power Supply
Line Level
Audio In
Line Level
Audio Out
Main Monitor
(HDMI)
Main Monitor
(VGA)
Web Remote
Client
PowerVideo Plus
(CMS)
NVR Smart Switch
Mouse &
EKB200 Keyboard
IP Cameras 1 ~ 8
Network
EVNR8304D-8CH
1
2
3
4
5
6
7
8
Figure 2-7
1. Using the supplied Power Cord, connect one end to the 100-240 VAC~ port on the NVR and
the other end to the 100-240 VAC~ power outlet.
2. To view videos, connect a monitor to the HDMI or VGA port using the HDMI or VGA cable
supplied by the monitor manufacturer.
3. To manage the NVR over network, use a standard RJ-45 CAT5 10/100Mb Ethernet cable to
connect the WLAN port of the NVR to the network. Please refer to 2.5 Connecting the NVR to
the Network.
4. Connect the LAN port of the NVR to a PoE device using a standard RJ-45 CAT5 10/100Mb
Ethernet cable. Please see 2.3.1 Camera Connection for more details.
5. Connect the IP cameras to the 1~8 camera ports at the rear of the PoE switch using Ethernet
cables without separate power sources. Please see 2.3.1 Camera Connection for more
details.
6. Optionally connect a mouse or a keyboard (EKB200) to the NVR to control the system. You
can also control the system using the supplied IR Remote Controller.
7. Connect the audio input devices to the NVR.
8. To listen to audio of video source, connect speakers to the Audio Out port. Note that
speakers with amplifier are required.