EverFocus eIVP-CFS-IV-V0004 User manual

eIVP-CFS-IV-V0004
AI Mobile NVR
Intel® Core™ i7/i5 with 4 PoE Ports
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: August 2020

EVERFOCUS ELECTRONICS CORPORATION
eIVP-CFS-IV-V0004 AI Mobile NVR
Intel® Core™ i7/i5 with 4 PoE Ports
User’s Manual
1995-2020 EverFocus Electronics Corp.
www.everfocus.com.tw
Disclaimer
All the images including product pictures or screen shots in this document are for example only. The
images may vary depending on the product and software version. Information contained in this
document is subject to change without notice.
Copyright
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any
form or by any means without written permission of the EverFocus Electronics Corporation.
-Microsoft Windows is a registered trademark of Microsoft Corp.
-Intel, Pentium, Celeron are registered trademarks of Intel Corporation
-Core, Atom are trademarks of Intel Corporation
-ITE is a trademark of Integrated Technology Express, Inc.
-IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
All other product names or trademarks are properties of their respective owners.

eIVP-CFS-IV-V0004
ii
Safety Precautions
Please read the following safety instructions carefully. It is advised that you keep this
manual for future references.
All cautions and warnings on the device should be noted.
All cables and adapters supplied by EverFocus are certified and in accordance with the
material safety laws and regulations of the country of sale. Do not use any cables or
adapters not supplied by EverFocus to prevent system malfunction or fires.
Make sure the power source matches the power rating of the device.
Position the power cord so that people cannot step on it. Do not place anything over
the power cord.
Always completely disconnect the power before working on the system’s hardware.
No connections should be made when the system is powered as a sudden rush of
power may damage sensitive electronic components.
If the device is not to be used for a long time, disconnect it from the power supply to
avoid damage by transient over-voltage.
Always disconnect this device from any AC supply before cleaning.
While cleaning, use a damp cloth instead of liquid or spray detergents.
Make sure the device is installed near a power outlet and is easily accessible.
Keep this device away from humidity.
Place the device on a solid surface during installation to prevent falls.
Do not cover the openings on the device to ensure optimal heat dissipation.
Watch out for high temperatures when the system is running.
Do not touch the heat sink or heat spreader when the system is running.
Never pour any liquid into the openings. This could cause fire or electric shock.
As most electronic components are sensitive to static electrical charge, be sure to
ground yourself to prevent static charge when installing the internal components. Use a
grounding wrist strap and contain all electronic components in any static-shielded
containers.
If any of the following situations arises, please contact our service personnel
([e-mail]):
-Damaged power cord or plug
-Liquid intrusion to the device
-Exposure to moisture
-Device is not working as expected or in a manner as described in this manual
-The device is dropped or damaged
-Any obvious signs of damage displayed on the device
DO NOT LEAVE THIS DEVICE IN AN UNCONTROLLED ENVIRONMENT WITH
TEMPERATURES BEYOND THE DEVICE’S PERMITTED STORAGE TEMPERATURES (SEE
SPECIFICATION) TO PREVENT DAMAGE.

eIVP-CFS-IV-V0004
iii
FCC Statement
This device complies with Part 15 FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received including
interference that may cause undesired operation.
Caution:
There is a danger of explosion if the battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions and your local government’s recycling or
disposal directives.
Attention:
Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte.
Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le constructeur.
Recycler les batteries usées en accord avec les instructions du fabricant et les directives
gouvernementales de recyclage.

eIVP-CFS-IV-V0004
iv
TABLE OF CONTENTS
1. Introduction .......................................................................................................................1
1.1 Features .....................................................................................................................1
1.2 Dimensions.................................................................................................................2
1.3 Packing List.................................................................................................................2
1.4 Front Panel.................................................................................................................3
1.4.1 Power Button .........................................................................................................4
1.4.2 CFast Card ..............................................................................................................4
1.4.3 WLAN LED, Mini PCIe, SIM Card Comparison........................................................5
1.4.4 PWR & HDD LED Indicator .....................................................................................6
1.4.5 Ethernet Port .........................................................................................................6
1.5 Rear Panel ..................................................................................................................7
1.5.1 PoE Ports................................................................................................................8
1.5.2 Serial Port...............................................................................................................8
1.5.3 Isolated DIO............................................................................................................1
2. Connection and Installation...............................................................................................3
2.1 How to Open Your eIVP-CFS-IV-V0004 ......................................................................3
2.2 Installing DDR4 SO-DIMM Modules...........................................................................5
2.3 Installing Mini PCIe Card ............................................................................................7
2.4 Installing Antenna Cable ............................................................................................8
2.5 Installing CFast Card.................................................................................................10
2.6 Installing SIM Card ...................................................................................................11
2.7 Installing SSD/HDD...................................................................................................12
2.8 Installing M.2 ...........................................................................................................14
2.9 Mounting Your eIVP-CFS-IV-V0004..........................................................................15
2.9.1 Wall mount ..........................................................................................................16
2.9.2 VESA mount .........................................................................................................16
2.9.3 Din Rail Kit............................................................................................................17
2.9.4 2U rack mount kit ................................................................................................17
3. Jumpers and Connectors on the Motherboard ...............................................................18
3.1 Main Board Expansion Connectors..........................................................................18
3.1.1 Top View (Component Side) of eIVP-CFS-IV-V0004 Main Board With................18
3.1.2 Bottom View (Solder Side) of eIVP-CFS-IV-V0004 Main Board With Connector
Location............................................................................................................................19
3.1.3 Miscellaneous Pin Header....................................................................................19
3.1.4 SATA1, SATA2 : SATA III Connector......................................................................20
3.1.5 J2 : SATA Power Connector..................................................................................20
3.1.6 CN13 : Internal USB..............................................................................................21
3.1.7 SODIMM_1, SODIMM_1 : DDR4 Slot...................................................................21
3.1.8 CN1 : BIOS Socket.................................................................................................22
3.1.9 SUMIT A, SUMIT B................................................................................................23

eIVP-CFS-IV-V0004
v
3.1.10 Mini PCIe : MPCIe_1 , MPCIe_2 .......................................................................25
3.1.11 BAT1 : RTC Battery ...........................................................................................27
3.1.12 FN1 : FAN Header.............................................................................................27
3.1.13 CN3 : LPC Port 80 Header ................................................................................28
3.1.14 J4, J5 : LAN3, LAN4, LAN5, LAN6 Speed LED Header .......................................28
3.1.15 M.2 KEY E : USB, PCIex2 support .....................................................................29
3.1.16 M.2 KEY M : PCIe x4/SATA Support .................................................................30
3.2 Main Board Jumper Settings....................................................................................32
3.2.1 Board top view of the system main board with jumper and deep switch ..........32
3.2.2 JP6 : USB Wake Up...............................................................................................33
3.2.3 JP2, JP3, JP4, JP5 : COM Port RI pin Select...........................................................33
3.2.4 JP7 : PoE Power ON Select ...................................................................................34
3.2.5 JCMOS1, JP1 : CMOS & ME Flash.........................................................................34
3.3 Ignition Control ........................................................................................................35
3.3.1 Adjust Ignition Control Modes.............................................................................35
3.3.2 Ignition Control Wiring ........................................................................................36
4. BIOS Setup........................................................................................................................38
4.1 Entering BIOS Setup .................................................................................................38
4.2 Main .........................................................................................................................39
4.3 Advanced .................................................................................................................39
4.3.1 CPU Configuration................................................................................................40
4.3.2 Power & Performance .........................................................................................41
4.3.2.1 CPU – Power Management Control.............................................................41
4.3.2.2 GT – Power Management Control ...............................................................42
4.3.3 PCH-FW Configuration .........................................................................................42
4.3.4 Trusted Computing ..............................................................................................43
4.3.5 ACPI Settings ........................................................................................................43
4.3.6 SMART Settings....................................................................................................43
4.3.7 IT8786 Super IO Configuration ............................................................................44
4.3.7.1 Serial Port X Configuration...........................................................................44
4.3.8 Hardware Monitor ...............................................................................................44
4.3.9 Serial Port Console Redirection ...........................................................................45
4.3.10 Intel TXT Information.......................................................................................46
4.3.11 Acoustic Management Configuration..............................................................46
4.3.12 PCI Subsystem Setting......................................................................................46
4.3.13 Network Stack Configuration...........................................................................47
4.3.14 CSM Configuration ...........................................................................................48
4.3.15 NVMe Configuration ........................................................................................49
4.3.16 USB Configuration............................................................................................49
4.4 Chipset .....................................................................................................................50
4.4.1 System Agent (SA) Configuration.........................................................................50
4.4.1.1 Memory Configuration ................................................................................51
4.4.1.2 Graphics Configuration ................................................................................51
4.4.1.3 PEG Port Configuration................................................................................52
4.4.2 PCH-IO Configuration...........................................................................................52
4.4.2.1 PCI Express Configuration of PCH-IO ...........................................................53
4.4.2.2 SATA and RST Configuration ........................................................................54

eIVP-CFS-IV-V0004
vi
4.4.2.3 Security Configuration .................................................................................55
4.5 Security ....................................................................................................................55
4.5.1 HDD Security Configuration.................................................................................56
4.5.2 Security Boot........................................................................................................56
4.6 Boot..........................................................................................................................57
4.7 Save & Exit ...............................................................................................................58
5. Appendix ..........................................................................................................................59
5.1 Function Description................................................................................................59
5.2 Isolated DIO Signal Circuit........................................................................................60
5.3 RAID Functions.........................................................................................................61
5.3.1 SATA Mode for RAID ............................................................................................61
5.3.2 UEFI Mode for RAID .............................................................................................61

eIVP-CFS-IV-V0004
1
1. Introduction
The eIVP-CFS-IV-V0004 is one of EverFocus’ IPC products with rugged design that uses Intel® Core™
i7/i5. By installing with EverFocus’ AiO NVR software, this model can be used as an AI NVR for
transportation market or general and commercial markets.
The model supports up to 4 PoE ports, wide operating temperature ranging from -40°C to 75°C, wide
DC power range between 6V and 36V, and 80V surge protection with ignition pin. It also features
comprehensive storage and interface options including up to two 2.5 SSD trays, two SIM sockets, one
CFast socket, one M.2 key E socket,six USB 3.1, four COM RS-232/422/485, sixteen isolated DIO for
connecting to other devices.
The vibration of eIVP-CFS-IV-V0004’s SSD is certificated with IEC 60068-2-64 while the shock is
certificated with IEC 60068-2-27. It supports onboard GPS and GLONASS. Besides, the model is also
CE, FCC, EN50155, EN50121-3-2 and RoHS certified. The eIVP-CFS-IV-V0004 AI NVR carries everything
you need for computing in your application.
1.1 Features
•In-vehicle network video recorder platform
•8 Cores 9th Generation Intel® Core™ i7/i5 Processor
•(Coffee Lake Refresh) with Intel® C246 Chipset
•Fanless, -40°C to 75°C Operating Temperature
•6 Independent GigE LAN with 4 IEEE 802.3at PoE+
•SIM Sockets for WiFi/4G/3G/LTE/GPRS/UMTS
•2 2.5 SSD Tray, 2 SIM Socket, 1 CFast Socket, 2 M.2 Socket
•6 USB 3.1, 4 COM RS-232/422/485, 16 Isolated DIO
•Expansion : SUMIT A, B, M.2, up to 5 Mini PCIe
•6V to 36V DC Power Input with 80V Surge Protection
•Configurable Ignition Power Control
•CE, FCC, EN50155, EN50121-3-2, RoHS certified
Chapter
1

eIVP-CFS-IV-V0004
2
1.2 Dimensions
1.3 Packing List
•NVR x 1
•Foot pad x 4
•Wall-mounting bracket x 2
•SSD/HDD tray key x 2
•Drivers & utilities DVD x 1
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your
local EverFocus office or agents for more information. Please also keep the shipping carton
for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
3. The DVD contains the User Manual and some Drivers for the system. If you can’t find the
required drivers from the DVD, please go to our website for related drivers.
www.everfocus.com.tw
Item Description Outlook Usage Qty
1 PHILLPIS M4x16L with washer, Ni
Mount 4
2 PHILLPIS M2.5x6L, Ni
Mini PCIe slot 4
3 PHILLPIS M3x6L, Ni+Ny
M.2 2
4 PHILLPIS
#10-32x6L, Ni
Wall mount
bracket
6
5 Terminal block 3-pin (5.0mm)
DC-IN/Switch 2
6 Terminal block 20-pin (2.54mm)
Isolated DIO/
GPIO
1

eIVP-CFS-IV-V0004
3
1.4 Front Panel
124
356
8
9
7
11
10
12
No. Name Description
1. Reset Tact
Switch
It is a hardware reset switch. Use this switch to reset the system
without powering off the system. Press the Reset Switch for a few
seconds, and then reset will be enabled.
2. Power Button Press the button to turn on or turn off the system. For more details,
please refer to 1.4.1 Power Button.
3. CFast Card
The eIVP-CFS-IV-V0004 does not support the CFast hot swap.Be sure to
disconnect the power source and unscrew the CFast socket cover
before installing a CFast card. For more details, please refer to 1.4.2
CFast Card.
4.
WLAN LED,
Mini PCIe,
SIM Card
Comparison
The SIM card sockets do not support hot-plug. Please make sure to
unplug the system power before inserting the SIM card(s). For more
details, please refer to 1.4.3 WLAN LED, Mini PCIe, SIM Card
Comparison.
5. PWR & HDD
LED Indicator
HDD LED/Yellow : A Hard Disk/CFast LED. If the LED is on, it indicates
that the system's storage is functional. If it is off, it indicates that the
system's storage is not functional. If it is flashing, it indicates that data
access activities. For more details, please refer to 1.4.4 PWR & HDD LED
Indicator.
6. DisplayPort Onboard Display Port supports up to 4096x2304 resolution at 60Hz.
7. DVI-D
Connector
You can use the DVI-D connector on the front panel to connect to a
display device. The DVI-D supports 1920 x 1200 resolution output. You
will need a DVI-D cable when connecting to a display device.
8. DVI-I
Connector
You can use the DVI-I connector to connect to a display device. The DVI-
I supports 1920 x 1200 resolution output. You will need a DVI-I cable
when connecting to a display device. You can optionally use a DVI-I to
VGA cable/connector if you want to connect to a VGA display device.

eIVP-CFS-IV-V0004
4
9. USB3.1 Ports
There are 4 USB 3.1 connections available supporting up to 5Gb per
second data rate in the front side. It is also compliant with the
requirements of Super Speed (SS), high speed (HS), full speed (FS) and
low speed (LS).
10. Ethernet Port
There are 2 8-pin RJ-45 jacks supporting 10/100/1000 Mbps Ethernet
connections in the front side. When both LAN 1 and LAN 2 work in
normal status, iAMT 12.0 function is enabled. Both of LAN 1 and LAN 2
support Wake on LAN and Pre-boot functions. For more details, please
refer to 1.4.5 Ethernet Port.
11. Audio
Connector
There are 2 audio connectors, Mic-in and Line-out. Onboard Realtek
ALC892 audio codec supports 5.1 channel HD audio and fully complies
with Intel® High Definition Audio (Azalia) specifications.
To utilize the audio function in Windows platform, you need to install
corresponding drivers for both Intel Sunrise Point chipset and Realtek
ALC892 codec.
12. SSD/HDD Tray
There are 2 front-access 2.5" SSD/HDD trays in the front side. Just pull
the trigger to open the SSD/HDD tray. Make sure the system is
powered-off. Unlock the SSD Tray using the supplied SSD Lock Key.
1.4.1 Power Button
The Power Button is a non-latched switch with dual color LED indication. It indicates power status:
S0, S3 and S5. More details of LED indications are listed as follows:
LED Color Power Status System Status
Solid Blue S0 System working
Solid Orange S3, S5 Suspend to RAM, System off with
standby power
To power on the system, press the power button and then the blue LED is lightened. To power off
the system, you can either command shutdown by OS operation, or just simply press the power
button.
1.4.2 CFast Card
If a system error occurs, you can just press the power button for 4 seconds to shut down the machine
directly. Please do note that a 4-second interval between each 2 power-on/power-off operation is
necessary in normal working status. (For example, once you turn off the system, you have to wait for
4 seconds to initiate another power-on operation).
There is a CFast socket on the front panel supporting Type-I/II Compact Flash card. It is implemented
by a SATA III Port from C246 PCH. Be sure to disconnect the power source and unscrew the CFast
socket cover before installing a CFast card. The eIVP-CFS-IV-V0004 does not support the CFast hot

eIVP-CFS-IV-V0004
5
swap and PnP (Plug and Play) functions. It is necessary to remove power source first before inserting
or removing the CFast card.
The pinouts of CFast port are listed as follows:
Pin No. Description Pin No. Description
S1 GND PC6 NC
S2 SATA_TXP5 PC7 GND
S3 SATA_TXN5 PC8 CFAST_LED
S4 GND PC9 NC
S5 SATA_RXN5 PC10 NC
S6 SATA_RXP5 PC11 NC
S7 GND PC12 NC
PC1 GND PC13 +3.3V
PC2 GND PC14 +3.3V
PC3 NC PC15 GND
PC4 NC PC16 GND
PC5 NC PC17 NC
1.4.3 WLAN LED, Mini PCIe, SIM Card Comparison
Mini PCIe Slot/SIM Slot/WLAN LED Mapping Table:
Mini PCle
SIM
LED
MPCIe 1
SIM 1 (CN9)
1
MPCIe 1
SIM 2 (CN10)
2

eIVP-CFS-IV-V0004
6
1.4.4 PWR & HDD LED Indicator
Power LED/Green: If the LED is solid green, it indicates that the system is powered on.
LED Color
Indication
System Status
Yellow HDD/CFast •On/Off: Storage status, function or not.
•Twinkling: Data transferring.
Green Power System power status (on/off)
1.4.5 Ethernet Port
There are 2 8-pin RJ-45 jacks supporting 10/100/1000 Mbps Ethernet connections in the front side.
LAN 1 is powered by Intel® i219 Ethernet Phy; LAN 2 is powered by Intel® I210 Ethernet engine.
When both LAN 1 and LAN 2 work in normal status, iAMT 12.0 function is enabled.
Using suitable RJ-45 cable, you can connect the system to a computer, or to any other devices with
Ethernet connection, such as hubs and switches. Moreover, both of LAN 1 and LAN 2 support Wake
on LAN and Pre-boot functions. The pin-outs of LAN 1 and LAN 2 are listed as follows:
Pin No. 10/100Mbps 1000Mbps
1 E_TX+ MDI0_P
2 E_TX- MDI0_N
3 E_RX+ MDI1_P
4 ----- MDI2_P
5 ----- MDI2_N
6 E_RX- MDI1_N
7 ----- MDI3_P
8 ------ MDI3_N
Each LAN port is supported by standard RJ-45 connector with LED indicators to present
Active/Link/Speed status of the connection.
The LED indicator on the right bottom corner lightens in solid green when the cable is properly
connected to a 100Mbps Ethernet network; The LED indicator on the right bottom corner lightens in
solid orange when the cable is properly connected to a 1000Mbps Ethernet network; The left LED will
keep twinkling/off when Ethernet data packets are being transmitted/received.

eIVP-CFS-IV-V0004
7
1.5 Rear Panel
12 3 45
6
No.
Name
Description
1 PoE Ports
The LED indicator lightens in solid green when the cable is properly
connected to a 100 Mbps Ethernet network; The LED indicator lightens
in solid orange when the cable is properly connected to a 1000 Mbps
Ethernet network; The left LED will keep twinkling/off when Ethernet
data packets are being transmitted/received. For more details, please
refer to 1.5.1 PoE Ports.
2 Serial Port
Serial port 1 to 4 (COM 1 to 4) can be configured for RS-232, RS-422, or
RS-485 with auto flow control communication. The default definition of
COM 1 and COM 2 is RS-232. If you want to change to RS-422 or RS-485,
you can find the setting in BIOS. For more details, please refer to 1.5.2
Serial Port.
3 USB Port
There are 2 USB 3.1 connections available supporting up to 5Gb per
second data rate. It is also compliant with the requirements of Super
Speed (SS), high speed (HS), full speed (FS) and low speed (LS).
4 Isolated
DIO
There is a 16-bit (8-bit DI, 8-bit DO) connectors in the rear side. DI/DIO
support NPN (sink) and PNP (Source) mode. Each DI pin is equipped with
a photocoupler for isolated protection. For more details, please refer to
1.5.3 Isolated DIO.
5
Remote
Power
On/Off
Switch &
LED
Terminal
Block
It is a 2-pin power-on or power-off switch through Phoenix Contact
terminal block. You could turn on or off the system power by using this
contact. This terminal block supports dual function of soft power-
on/power-off (instant off or delay 4 second), and suspend mode.
Pin 1: Ignition Pin2 : SW+Pin3 : SW-
6
Power
Terminal
Block
eIVP-CFS-IV-V0004 supports 6V to 36V DC power input by terminal block
in the rear side. In normal power operation, power LED lightens in solid
green. eIVP-CFS-IV-V0004 supports up to 80V surge protection.
Pin 1: V+ Pin2 : V-Pin3 : Chassis Ground

eIVP-CFS-IV-V0004
8
1.5.1 PoE Ports
There are 4 RJ45 connectors in the rear side. It supports IEEE 802.3 at (PoE+) Power over Ethernet
(PoE) connection delivering up to 37W/54V per port and 1000 BASE-T gigabit data signals over
standard Ethernet Cat 5/Cat 6 cable.
Each PoE connection is powered by Intel® I210 Gigabit Ethernet controller and independent PCI
express interface to connect with multi-core processor for network and data transmit optimization.
Only when PoE port starts to supply power to power devices, the dedicated LED will be lightened.
PS. Suggest to use PoE function when power input is over 12V.
The pin-outs of LAN 3 and LAN 6 are listed as follows:
Pin No.
10/100Mbps
1000Mbps
PoE
1
E_TX+
MDI0_P
PoE+
2
E_TX-
MDI0_N
PoE+
3
E_RX+
MDI1_P
PoE-
4
-----
MDI2_P
-----
5
-----
MDI2_N
-----
6
E_RX-
MDI1_N
PoE-
7
-----
MDI3_P
-----
8
------
MDI3_N
-----
Each LAN port is supported by standard RJ-45 connector with LED indicators to present
Active/Link/Speed status of the connection.
The LED indicator on the right bottom corner lightens in solid green when the cable is properly
connected to a 100 Mbps Ethernet network; The LED indicator on the right bottom corner lightens in
solid orange when the cable is properly connected to a 1000 Mbps Ethernet network; The left LED
will keep twinkling/off when Ethernet data packets are being transmitted/received.
LED
Location
LED Color 10Mbps 100Mbps 1000Mbps
Right Green/
Orange
Off Solid Green Solid
Orange
Left Yellow Twinkling
Yellow
Twinkling
Yellow
Twinkling
Yellow
POE LED
LED Color
POE Status
LED 3-6
Solid Green
POE ON
1.5.2 Serial Port
Serial port 1 to 4 (COM 1 to 4) can be configured for RS-232, RS-422, or RS-485 with auto flow control
communication. The default definition of COM 1 and COM 2 is RS-232. If you want to change to RS-
422 or RS-485, you can find the setting in BIOS.
BIOS Setting
Function
COM 1
RS-232
RS-422 (5-wire)
1 8

eIVP-CFS-IV-V0004
9
COM 2
COM 3
COM 4
RS-422 (9-wire)
RS-485
RS-485 w/z auto-flow control
The pin assignments are listed in the following table:
Serial
Port
Pin No.
RS-322
RS-422
(5-wire)
RS-422
(9-wire)
RS-485
(3-wire)
1 to 4
1
DCD
TXD-
TXD-
DATA-
2
RXD
TXD+
TXD+
DATA+
3
TXD
RXD+
RXD+
-----
4
DTR
RXD-
RXD-
-----
5
GND
GND
GND
GND
6
DSR
-----
RTS-
-----
7
RTS
-----
RTS+
-----
8
CTS
-----
CTS+
-----
9
RI
-----
CTS-
-----

eIVP-CFS-IV-V0004
1
1.5.3 Isolated DIO
There is a 16-bit (8-bit DI, 8-bit DO) connectors in the rear side. DI/DIO support NPN (sink) and
PNP (Source) mode, Each DI pin is equipped with a photocoupler for isolated protection. Each
DO pin is equipped with isolator function, DO Safety-Related Certifications:
•4242-VPK Basic Isolation per DIN V VDE V 0884-10 and DIN EN 61010-1
•3-KVRMS Isolation for 1 minute per UL 1577
•CSA Component Acceptance Notice 5A, IEC 60950-1 and IEC 61010-1 End
Equipment Standards
•GB4943.1-2011 CQC Certified
DIO Connectors pin out:
DIO Pin No. Definition Function
DIO
1
INPUT 0
SIO_GPI70
2
INPUT 1
SIO_GPI71
3
INPUT 2
SIO_GPI72
4
INPUT 3
SIO_GPI73
5
INPUT 4
SIO_GPI74
6
INPUT 5
SIO_GPI75
7
INPUT 6
SIO_GPI76
8
INPUT 7
SIO_GPI77
9
DI_COM
-----
10
DIO GND
-----
11
OUTPUT 0
SIO_GPO80
12
OUTPUT 1
SIO_GPO81
13
OUTPUT 2
SIO_GPO82
14
OUTPUT 3
SIO_GPO83
15
OUTPUT 4
SIO_GPO84
16
OUTPUT 5
SIO_GPO85
17
OUTPUT 6
SIO_GPO86
18
OUTPUT 7
SIO_GPO87
19
DIO_GND
-----
20
External 6-40VDC
(NPN) External 6-
48VDC (PNP)
-----

eIVP-CFS-IV-V0004
2
DI reference circuit :
DO reference circuit :
Sink Mode (NPN, Default)
Source (PNP)
Sink Mode (NPN)
Source Mode (PNP)

eIVP-CFS-IV-V0004
3
2. Connection and Installation
2.1 How to Open Your eIVP-CFS-IV-V0004
Step 1 Turn eIVP-CFS-IV-V0004 bottom side up and remove 6pcs HEX#6-32 crews from the
front panel.
Step 2 Remove front panel.
Step 3 Turn over eIVP-CFS-IV-V0004 to face the rear side.
Chapter
2

eIVP-CFS-IV-V0004
4
Step 4 Remove 5pcs HEX#6-32 screws (circled in red) from the rear side and 4pcs PHILLIPS#6-
32 screws (circled in yellow) from the bottom side.
Step 5 Remove rear panel.
Step 6 Remove the SATA cable and SATA power cables.