EverFocus ERS-4 User manual

Instruction Manual
E
ER RS S- -4 4
4
4 C Ch ha an nn ne el l V Vi id de eo o S Se er rv ve er r / / R Re ec co or rd de er r

All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by
any means without written permission of the Everfocus Electronics Corporation.
Release Date: Feb. 2010
QuickTime is a registered trademark of the Apple Computer, Inc.
iPhone is a registered trademark of the Apple Computer, Inc.
RealPlayer is a registered trademark of the RealNetworks, Inc.
Windows is a registered trademark of the Microsoft Corporation.
Linksys is a registered trademark of the Linksys Corporation.
D-Link is a registered trademark of the D-Link Corporation.
DynDNS is a registered trademark of the DynDNS.org Corporation.
Other product and company names mentioned herein may be the trademarks of their respective owners.

ii
Safety Precautions
• To avoid any damage, please consider the following safety warnings:
• Never place the device near to heaters, furnaces, other heat sources or under direct solar irradiation.
• Operate the device only in locations providing the tolerable operating temperature range 0°C~40°C/32°F ~ +104°F.
• Make sure that the device‘s ventilation slots are not covered or sheeted.
• For cleaning, make sure the device is plugged off and only use a damp cloth without acid detergent.
• Install the device only in dry and dustproof surroundings. Protect the device against any liquid‘s penetration.
• Avoid the penetration of any artefacts, e.g. through ventilation slots.
• Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There are no user-
serviceable parts inside. Contact qualified service personnel for maintenance. Handle the appliance with care. Do not strike
or shake, as this may damage the appliance.
• Do not operate appliance with other than specified power supplies.
• Avoid any affection of the device through vibrations or mechanical shock at the recorder‘s installation location.
• Avoid to power off the device during playback or recording operation.
This Product is RoHS compliant.
ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in this case, the user may be
urged to take adequate measures.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures :
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users’
authority to operate this equipment.
WEEE
The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve his products.
Therefore, all specifications are subject to change without prior notice. Misprints reserved.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.
Y
our EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!

iii
TABLE OF CONTENTS
1PRODUCT OVERVIEW..........................................................................................................................1
1.1 FEATURES........................................................................................................................................1
1.2 PACKAGE CONTENTS....................................................................................................................1
1.3 OPTIONAL ACCESSORIES.............................................................................................................1
1.4 SPECIFICATIONS.............................................................................................................................2
1.5 FRONT PANEL..................................................................................................................................3
1.6 REAR PANEL CONNECTORS.........................................................................................................4
2INSTALLATION......................................................................................................................................5
2.1 VIDEO INPUTS/OUTPUTS INSTALLATION....................................................................................5
2.2 AUDIO INSTALLATION.....................................................................................................................6
2.3 ALARM CONTACTS INSTALLATION ..............................................................................................7
2.3.1 Alarm Input Contacts...................................................................................................................7
2.3.2 Alarm Output Relay.....................................................................................................................7
2.4 RS-485 KEYBOARD /PTZ INSTALLATION.....................................................................................8
2.4.1 General RS-485 bus installation..................................................................................................8
2.4.2 RS-485 terminal pin assignment.................................................................................................9
2.4.3 Speed Dome Installation .............................................................................................................9
2.5 USB-MOUSE INSTALLATION........................................................................................................10
2.6 MONITORCONNECTION.....................................................................................................................11
2.7 NETWORK CONNECTION.............................................................................................................11
2.7.1 Direct PC Connection through Crossover Network Cable........................................................11
2.7.2 Network Connection through Patch Cable................................................................................12
2.8 FINAL INSTALL PROCESS............................................................................................................12
3CONFIGURATION VIA NETWORK.....................................................................................................13
3.1 IP-SETUP VIA NETWORK WITH IP-UTILITY................................................................................13
3.2 CONNECTING TO ERS-4...............................................................................................................14
3.3 BROWSER SECURITY SETTING..................................................................................................15
3.3.1 Installing ActiveX controls..........................................................................................................15
3.3.2 Enabling ActiveX Controls.........................................................................................................17
3.4 REMOTE LIVE SCREEN................................................................................................................20
3.5 REMOTE SETUP - EXPRESS........................................................................................................22
3.6 REMOTE SETUP - CAMERA .........................................................................................................25
3.6.1 Camera: Basic settings..............................................................................................................25
3.6.2 Camera: Video Adjust................................................................................................................27
3.6.3 Camera: Motion.........................................................................................................................28
3.6.4 Camera: Video Loss..................................................................................................................30
3.7 REMOTE SETUP: RECORD ..........................................................................................................32
3.7.1 Record: Record..........................................................................................................................32
3.8 REMOTE SETUP: ALARM..............................................................................................................33
3.8.1 Alarm: Alarm..............................................................................................................................33
3.8.2 Alarm: Event..............................................................................................................................35

iv
3.8.2.1 Event: Fan failure......................................................................................................................35
3.8.2.2 Event: HD Temperature............................................................................................................36
3.8.2.3 Event: HD failure.......................................................................................................................37
3.8.2.4 Event: HDD Full.........................................................................................................................38
3.8.2.5 Event: HD Off............................................................................................................................39
3.8.2.6 Event: Power Loss ....................................................................................................................40
3.8.2.7 Event: Network Loss .................................................................................................................41
3.9 REMOTE SETUP: SCHEDULE ......................................................................................................42
3.9.1 Schedule: Express Setup..........................................................................................................42
3.9.2 Schedule: Holidays....................................................................................................................44
3.9.3 Schedule: Schedule...................................................................................................................45
3.9.4 Schedule: Alarm Action.............................................................................................................48
3.10 REMOTE SETUP: NETWORK........................................................................................................50
3.10.1 Network: LAN.............................................................................................................................50
3.10.2 Network: Email...........................................................................................................................52
3.10.3 Network: DDNS .........................................................................................................................53
3.10.3.1 EverFocus DDNS....................................................................................................................53
3.10.3.2 Dyndns DDNS.........................................................................................................................55
3.10.4 Network: Alarm Server ..............................................................................................................56
3.11 REMOTE SETUP: DISK..................................................................................................................57
3.12 REMOTE SETUP: DISPLAY...........................................................................................................58
3.12.1 Monitor OSD..............................................................................................................................58
3.12.2 Main M/T SEQ: Sequence.........................................................................................................59
3.13 REMOTE SETUP: SYSTEM...........................................................................................................60
3.13.1 System: Date / Time..................................................................................................................60
3.13.2 System: Daylight Saving............................................................................................................61
3.13.3 System: User.............................................................................................................................62
3.13.3.1 User right definition.................................................................................................................62
3.13.3.2 Edit user account.....................................................................................................................63
3.13.3.3 Add user account ....................................................................................................................64
3.13.3.4 Delete user account................................................................................................................64
3.13.4 System: I/O Control...................................................................................................................65
3.13.5 System: Miscellaneous..............................................................................................................66
4NETWORK OPERATION .....................................................................................................................67
4.1 LIVE SCREEN CONTROLS............................................................................................................67
4.2 VIEW MODES.................................................................................................................................68
4.2.1 Full Screen.................................................................................................................................68
4.2.2 4 x Screen..................................................................................................................................68
4.2.3 Frameless Video Screen...........................................................................................................68
4.3 BIDIRECTIONAL AUDIO.................................................................................................................68
4.4 PLAYBACK SEARCH......................................................................................................................69
4.4.1 Event Search.............................................................................................................................69
4.4.2 Time / Date Search....................................................................................................................72
4.5 VIDEO COPY / EXPORT................................................................................................................73
4.5.1 Export File Evaluation with EFPlayer Software.........................................................................74
4.6 PTZ CONTROL...............................................................................................................................75
4.7 INFO................................................................................................................................................76
4.7.1 Info: System...............................................................................................................................76

v
4.7.2 Info: Log.....................................................................................................................................77
4.7.2.1 View Log....................................................................................................................................78
4.7.2.2 Delete Log.................................................................................................................................78
4.7.2.3 Export LOG................................................................................................................................78
5APPENDIX A: HDD ASSEMBLING.....................................................................................................79
5.1 OPEN ERS-4 HOUSING.................................................................................................................80
5.2 MOUNTING HDD BRACKETS........................................................................................................81
5.3 ASSEMBLING COOLER FAN.........................................................................................................82
5.4 SATA AND POWER CABLE INSTALLATION................................................................................83
5.5 HDD MOUNTING IN HOUSING......................................................................................................84
5.6 CLOSING ERS-4 HOUSING...........................................................................................................85
6APPENDIX B: 3GPP MOBILE PHONE STREAMING.........................................................................86
6.1 GENERAL REQUIREMENTS.........................................................................................................86
6.2 APPLE IPHONE..............................................................................................................................86
6.3 OTHER MOBILE PHONES.............................................................................................................87
7APPENDIX C: NETWORKING.............................................................................................................88
7.1 NETWORKING OVERVIEW...........................................................................................................88
7.1.1 Introduction to TCP/IP...............................................................................................................88
7.1.2 Subnet Masks............................................................................................................................88
7.1.3 Gateway Address......................................................................................................................88
7.1.4 Virtual Ports...............................................................................................................................88
7.2 WHAT IS YOUR NETWORK SETUP? ...........................................................................................90
7.2.1 Simple One to One Connection.................................................................................................90
7.2.2 Direct High Speed Modem Connection.....................................................................................95
7.2.3 Router or LAN Connection ........................................................................................................97
7.3 LINKSYS & D-LINK PORT FORWARDING....................................................................................99
7.3.1 Linksys Port Forwarding............................................................................................................99
7.3.2 D-Link Port Forwarding............................................................................................................102
8APPENDIX D: TIMING OF ALARM MODES.....................................................................................104
9APPENDIX E: CHANGING RULE FOR EXPRESS SETUP..............................................................107
10 APPENDIX E: LOCAL SETUP AT ERS-4.........................................................................................109
10.1 OPEN CONFIGURATION MENU .................................................................................................109
10.2 EXPRESS.......................................................................................................................................109
10.3 CAMERASETTING..........................................................................................................................112
10.3.1 Basic Setting............................................................................................................................112
10.3.2 Video Adjust.............................................................................................................................114
10.3.3 Motion......................................................................................................................................115
10.3.4 Video Loss...............................................................................................................................117
10.4 RECORD SETTING ......................................................................................................................118
10.5 ALARM & EVENT SETTING.........................................................................................................119
10.5.1 Alarm........................................................................................................................................119
10.5.2 Event........................................................................................................................................121
10.6 SCHEDULESETTING......................................................................................................................128
10.6.1 Express Setup .........................................................................................................................128

vi
10.6.2 Holidays...................................................................................................................................129
10.6.3 Schedule..................................................................................................................................130
10.6.4 Alarm Action ............................................................................................................................134
10.7 NETWORK ....................................................................................................................................138
10.7.1 LAN..........................................................................................................................................138
10.7.2 EMAIL......................................................................................................................................139
10.7.3 DDNS.......................................................................................................................................139
10.7.4 Alarm Server............................................................................................................................142
10.8 DISK SETTING..............................................................................................................................143
10.9 DISPLAY SETTING.......................................................................................................................144
10.9.1 Monitor OSD............................................................................................................................144
10.9.2 Main M/T SEQ.........................................................................................................................145
10.10 SYSTEM SETTING....................................................................................................................146
10.10.1 Date/Time.............................................................................................................................146
10.10.2 Daylight Saving.....................................................................................................................147
10.10.3 User......................................................................................................................................148
10.10.4 I/O Control.............................................................................................................................150
10.10.5 Misc.......................................................................................................................................151
10.11 INFORMATION...........................................................................................................................152
10.11.1 System..................................................................................................................................152
10.11.2 Log........................................................................................................................................153

ERS-4 Instruction Manual
1
1PRODUCT OVERVIEW
The ERS-4 is a 4 channel video server with local recording function for CCTV applications.
With the optional build-in HDD the ERS-4 is the ideal device for network operated CCTV systems with local
recording and low usage of systems network bandwidth.
The efficient H.264 compression with newest codec - technology allows fastnetwork video streaming in
excellent quality, furthermore an efficient usage of Hard Disk capacity at local recording.
The ERS-4 provides live and playback evaluation via network. Live view and setup menu are also
accessible at local monitor, operated by mouse.
1.1 FEATURES
•H.264 Compression format
•User friendly GUI with graphical icons and visual indicators
•Setup menu local (mouse, local monitor) or via network (Browser, CMS)
•Express Setup: by entering key parameters in EXPRESSmenu the ERS-4 is ready for operation
within a minute
•Audio recording capabilities
•Optional 1 internal SATA HDD
•Multi-language support
1.2 PACKAGE CONTENTS
ERS-4 videoserver x1
Quick Installation Guide x1
User’s Manual Disk x1
AC Adapter and Power Cord x1
1.3 OPTIONALACCESSORIES
ERS-HDMK: ERS-4 Hard Disk mounting kit for installing 3.5" SATA HDD to ERS-4-NH

ERS-4 Instruction Manual
2
1.4 SPECIFICATIONS
Physical
Recording Rate/Resolution 352x288: 100 IPS PAL / 120 IPS NTSC 704x288: 100 IPS PAL / 120 IPS NTSC
704x576: 50 IPS PAL / 60 IPS NTSC
Playback and Streaming
Rate/Resolution
352x288: up to 100 IPS PAL / 120 IPS NTSC
704x288: up to 100 IPS PAL / 120 IPS NTSC
704x576: up to 50 IPS PAL / 60 IPS NTSC
depending on network conditions
Video Input 4 x 1 Vpp FBAS, BNC, 75 Ohm termination
Monitor output 1 x 1 Vpp FBAS, BNC at 75 Ohm
1 x VGA ( resolution 800x600@60 Hz)
Audio Input/Output Input: 1 x Line In, 1 V max. / 1 KOhm, RCA socket
Output: 1 x Line Out 1 V max. at 1 KOhm, RCA socket
Alarm In 4 x N.O./N.C. , screw terminal connector
Alarm Out 1 x relay out N.O./N.C. , screw terminal connector
RS-485 1 x, screw terminal connector
Network interface 100 BASE-T, 8P8C / RJ45 socket
USB 1x USB 2.0 on Back Panel (for USB - Mouse)
1x USB 2.0 on Front Panel (for service purpose)
Status LED Power, Alarm, HDD activity, Network traffic
Clock Internal Real Time Clock, NTP synchronisation option
Power Source 12VDC with external power supply 100~240 VAC / 50/60 Hz
Dimensions (W x D x H) 320 x 208.9 x 54.3 mm / 12.6" x 8.2" x 2.1"
Temperature 0°C~40°C / 32°F~104°F (20~80% humidity)
Functional
OS Embedded Linux
Video Compression H.264
User Interface GUI(Graphical User Interface)
Operation Simultaneous network Live/Playback operation and local Recording
Recording Mode Manual, Schedule and Event
Playback Search By Date/Time or Event
Video Pause Yes
Video Loss Detection Yes
Motion Detection Yes
Event Log Yes
Schedule Setting Support Express and Advanced Schedule Setting
User Access 3 Levels of User Access Support
PTZ Protocols EverFocus, Pelco-D, Pelco-P, Samsung El., Transparent

ERS-4 Instruction Manual
3
1.5 FRONT PANEL
The front panelprovides 1 USB port and the status LEDs.
Figure 1-1 Front Panel
USB port: USB 2.0 interface PC - mouse or service purpose .
Status LED: POWER: LED ON indicates Power ON.
ALARM: LED ON indicates Alarm active.
HDD: LED flashes in case of HDD activity.
Net: LED flashes in case of Network activity.
Status - LED
USB-port

ERS-4 Instruction Manual
4
1.6 REAR PANEL CONNECTORS
Figure 1-2 Rear Panel
1. Power: Power in socket DC 12V
2. Alarm In: 4 alarm inputs for dry contacts in mode N.O. / N.C. , screw terminal connector
3. Alarm Out: Relay output N.C. / N.O. , screw terminal connector
4. RS485: RS-485 interface, screw terminal connector for PTZ devices and control keyboard
5. Audio In: Audio input, RCA socket for line audio signals 1V max., 10 KOhm impedance.
6. Audio Out: Audio output, RCA socket, line audio signal 1V max at 10 KOhm.
7. Video In: Video input for composite signals 1 Vpp , BNC, 75 Ohm terminated
8. Video Out: Video monitor output composite signal 1 Vpp at 75 Ohm termination, BNC
9. VGA: Video monitor output VGA 800x600 @ 60 Hz, 15 pin VGA socket
10. USB: USB 2.0 port for USB mouse
11. LAN: 100Base-T network interface , 8P8C / RJ-45 socket
1 2 4 6
3 5 7 8 9 10 11

ERS-4 Instruction Manual
5
2INSTALLATION
2.1 VIDEO INPUTS/OUTPUTS INSTALLATION
Camera and CCTV monitor must use 75 Ohm video cable (e.g. RG-59, RG-6, RG-11) with BNC
connectors.
Due to inappropriate absorbability, 50 Ohm coax cable (e.g. RG-58), antenna cable and other types of
coaxial cable are not compatible.
All connected video sources must provide a 1 Vpp NTSC orPAL standard video signal.
When converting transmission lines (twisted pair, fibre optics, radio) to the video inputs, be sure to verify
accurate receiver calibration.
All 4 video inputs are terminated with 75 Ohm.
ATTENTION: In order for the system to auto-detect the appropriate video format (NTSC or PAL), make
sure that there is a video signal on video input 1 upon power-up.

ERS-4 Instruction Manual
6
2.2 AUDIO INSTALLATION
The ERS-4 provides 1 audio input and 1 audio output.
The input is designed for 500 mV (max. 1 V) to 10 KOhm line audio signals.
ATTENTION: The direct connection of a non-amplified microphone is not supported (a microphone
amplifier is required).
The installation must be done with audio coax cable and RCA plugs.
The output provides a typ. 500 mV /max. 1V to 10 KOhm line audio signal and may be connected to a
monitor‘s audio input or active speaker. The direct connection of passive speakers is not supported.
AUDIO RECORDING FUNCTIONALITY:
The audio channel is assigned to video channel 1.
Audio recording is activated / deactivated in the camera menu, camera 1.
Audio channel is always recorded together with camera 1 and is independent of the image recording rate.

ERS-4 Instruction Manual
7
2.3 ALARM CONTACTS INSTALLATION
The ERS-4 alarm inputs can be used for recording startor recording rate adjustment. Furthermore, alarm
reactions such as camera switching to monitors, buzzer, Email and network alarm are available.
2.3.1 Alarm Input Contacts
ERS-4 provides 4 alarm inputs. All inputs are programmable N.O.(Normal Open)or N.C. (Normal Closed)
Inputs have to be switched by dry contacts, default setting is N.O..
Alarm input with N.O. (Normal Open) contact Alarm input with N.C. (Normal Closed) contact
in idle state in idle state
Alarm inputs 1~4 of ERS-4
All settings are programmed in the ALARM menu.
2.3.2 Alarm Output Relay
The relay output provides either NormallyOpen or Normally Closed dry contacts.
NC COM NO
Output relay in idle state

ERS-4 Instruction Manual
8
2.4 RS-485 KEYBOARD / PTZ INSTALLATION
The ERS-4 provides an RS-485 interface for PTZ control of speed domes and other PTZ devices.
Furthermore the ERS-4 can be remote-controlled by the EKB-500 universal keyboard. Keyboards and
speed domes can be installed on one single RS-485 bus. One system can comprise up to 8 keyboards.
2.4.1 General RS-485 bus installation
The ERS-4 uses a RS-485 simplex wiring; the signal is transferredvia a single twisted pair line. CAT5
network cable is recommended, UTP version (unshielded) is sufficient for normal application. A shielded
cable should be used if the installed cables are expected to be highly susceptible to interferences.
The number of devices installed in one bus is limited to 32, and the maximum cable length is 1200m. Both
of these can be expanded using a signal distributor (see below).
Both the first and the last device in series should be terminated with 120 Ohm resistance in order to
minimize line reflections.
RS-485 bus serial wiring
Cable length from box to device („Stubs“) has to be limited to 2m using connector boxes.
RS-485 bus serial wiring with connector boxes and connection cable
A direct RS-485 bus star wiring is not supported unlessusing a signal distributor (see below).
Improper RS-485 bus star wiring
A RS-485 signal distributor may be used to use a star wiring configuration.
Star wiring with RS-485 signal distributor

ERS-4 Instruction Manual
9
A RS-485 distributor can also be used to increase the maximum number of devices on the bus as well as
the total range. Each distributor output provides another RS-485 bus. This allows each output to extend an
additional 1200m, and it also enables the additional connection of 31 further devices to each output (the
output itself represents one device).
The maximum system expandability depends on the RS-485 address range of the installed devices.
System expansion with RS-485 signal distributor
ATTENTION: Most signal distributors are unidirectional! This means that the signal only flows from the
input towards the outputs. Therefore, e.g. the interconnection of several keyboards is not possible with
these types of signal distributor!
2.4.2 RS-485 terminal pin assignment
The following RS485 pin assignment as follow:
2.4.3 Speed Dome Installation
Speed dome or telemetry receiver pan/tilt/zoom control is available through web browser or the optional
PowerCon software ifthe ERS-4 is connected to a network.Local telemetry control is provided by USB -
mouse control or by the optional EKB-500 keyboard.
Supported protocols: EverFocus, Pelco-D, Pelco-P, Samsung, Transparent

ERS-4 Instruction Manual
10
Required ERS-4 settings: RS-485 receiver address in CAMERA menu
RS-485 parameters and protocol in the I/O CONTROL menu
ATTENTION: Some Pelco-D / -P protocol domes and receivers require an address offset of -1, i.e. the
address assigned to the dome / receiver in the ERS-4 camera menu must be 1 below the address set in the
dome / receiver itself!
2.5 USB-MOUSE INSTALLATION
For service and installation the ERS-4 can be operated by mouse at a local connected monitor.
All functions except playback and export are available at local operation.
Connect the USB mouse to the back panel USB port.
NOTE: Recommended mouse types are Logitech® and Microsoft® wired USB wheel-mouse. Wireless
USB mouse is not supported.

ERS-4 Instruction Manual
11
2.6 Monitor connection
For service and installation the ERS-4 can be operated by mouse at a local connected monitor.
All functions except playback and export are available at local operation.
The ERS-4 provides a composite Video output (BNC) and a VGA output (resolution 800x600 @ 60Hz) with
similar functionality. Depending on monitor type select one of these video outputs for monitor installation.
2.7 NETWORK CONNECTION
This section only describes physical connection to an Ethernet network. This step must be completed
before the ERS-4’s can connect to the network. Appendix C describes more Details for network
installations.
There are two basic types of connection:
2.7.1 Direct PC Connection through Crossover Network Cable
The point-to-point connection of ERS-4 and PC requires a crossover (crossed) network cable. This type of
connection is ONLY used for direct connection to a single PC. Make sure that the PC is equipped with a
10/100/1000 Mbps compatible network connection.
Figure 2-1 Direct PC Connection

ERS-4 Instruction Manual
12
Pin out of crossover-cable
2.7.2 Network Connection through Patch Cable
The connection to an existing network requires a normal patch cable (straight-through). The illustration
shows the connection to a network switch, router, or modem.
Figure 2-2 Network Connection through Patch Cable
Pin out of straight patch cable
2.8 Final Install Process
Once you have completed the basic wiring connections, you are ready to turn on the ERS-4. Plug in the
power source. The POWER LED will light up if power is normal. The system start-up will take ~ 1 minute
time.

ERS-4 Instruction Manual
13
3CONFIGURATION VIA NETWORK
3.1 IP-SETUP VIA NETWORK WITH IP-UTILITY
The ERS-4 configuration can be done via network or locally at the device, if USB - mouse and monitor are
connected.
This chapter describes the remote network setup the ERS-4 Menu Settings step by step.
Start the application „IPUtility.exe“ from the application CD-ROM.
Click on „Find Devices“.
If connected to the network, the ERS-4 will be listed.
Select the ERS-4 and click on „Login“:
Enter user name and password.
Defaults: User name: user1
Password: 11111111
After successful login the „set configuration“ button is activated (not greyed).
Enter the new IP—parameters, then click on „Set Configuration“.
After ~ 30 seconds check by clicking on „Find Devices“,if the new settings were taken over.