evertz 7700 Series User manual

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3
TABLE OF CONTENTS
1. OVERVIEW.......................................................................................................................................... 1
2. INSTALLATION................................................................................................................................... 4
2.1.1. Electrical Signal Connections.......................................................................................... 4
2.1.2. Optical Signal Connections ............................................................................................. 6
2.1.2.1. Single Fiber Version ......................................................................................... 6
2.1.2.2. Dual Fiber Versions.......................................................................................... 6
2.2. CARE AND HANDLING OF OPTICAL FIBER............................................................................ 7
2.2.1. Safety .............................................................................................................................. 7
2.2.2. Assembly......................................................................................................................... 7
2.2.3. Labeling........................................................................................................................... 7
2.2.4. Handling and Connecting Fibers..................................................................................... 8
3. SPECIFICATIONS............................................................................................................................... 9
3.1. SERIAL DIGITAL VIDEO OUTPUT...................................................................................................... 9
3.2. AES AUDIO OUTPUTS..................................................................................................................... 9
3.3. SERIAL DATA................................................................................................................................. 9
3.4. GENERAL PURPOSE INPUTS ........................................................................................................ 10
3.5. GENERAL PURPOSE OUTPUTS...................................................................................................... 10
3.6. OPTICAL INPUTS/OUTPUTS........................................................................................................... 10
3.7. ELECTRICAL ............................................................................................................................... 10
3.8. PHYSICAL ................................................................................................................................... 10
4. STATUS INDICATORS AND DISPLAYS ......................................................................................... 11
4.1. STATUS INDICATOR LEDS............................................................................................................. 11
4.2. DOT MATRIX DISPLAY.................................................................................................................. 12
4.2.1. Display Warning Status Indications............................................................................... 14
4.2.2. Displaying the Video Standard...................................................................................... 14
4.2.3. Displaying the Status of Input Video Embedded Audio Groups .................................... 14
4.2.4. Displaying the Received Optical Power ........................................................................ 15
4.2.5. Displaying the Firmware Version................................................................................... 15
4.2.6. Selection the Output Laser Enable Mode...................................................................... 15
4.2.7. Selecting Balanced or Unbalanced Audio..................................................................... 16
4.2.8. Selecting the Serial Data Type...................................................................................... 16

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3
4.2.9. Selecting the Serial Data Rate ...................................................................................... 16
4.2.10. Configuring the Serial Data Fail Safe Bias.................................................................... 17
4.2.11. Selecting Audio De-embedding Group.......................................................................... 17
4.2.12. Selecting Serial Data De-embedding Parameters......................................................... 18
4.2.13. Selecting GPIO De-embedding Parameters ................................................................. 19
4.2.14. Selecting Output Video HANC Cleaning ....................................................................... 20
4.2.15. Selecting Fiber Input Error Detection ............................................................................ 20
4.2.16. Selecting the Headphone Monitoring Jack Channel ..................................................... 20
4.2.17. Setting the Orientation of the Display............................................................................ 21
4.2.18. Selecting the Factory Reset Configuration.................................................................... 21
5. JUMPERS AND CONTROLS............................................................................................................ 22
5.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS ........................................................................................ 22
5.2. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES .............................................. 22
6. VISTALINK
®
REMOTE MONITORING/CONTROL........................................................................... 23
6.1. WHAT IS VISTALINK
®
?............................................................................................................... 23
6.2. VISTALINK
®
MONITORED PARAMETERS .............................................................................. 23
6.3. VISTALINK
®
CONTROLLED PARAMETERS ............................................................................... 24
6.4. VISTALINK
®
TRAPS.................................................................................................................... 24

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3
Figures
Figure 1-1: 7707MR-HD Block Diagram ...............................................................................................................3
Figure 2-1: 7707MR-HD Rear Plates & Pin Out....................................................................................................4
Figure 2-2: Reproduction of Laser Certification and Identification Label ..............................................................7
Figure 4-1: Location of Status Indicators and Jumpers ......................................................................................11
Figure 4-2: Card Edge Menu Structure ..............................................................................................................13
Tables
Table 1-1: 7707MR-HD Application Configuration ................................................................................................2
Table 6-1: VistaLINK
®
Monitored Parameters.....................................................................................................23
Table 6-2: VistaLINK
®
Controlled Parameters ....................................................................................................24
Table 6-3: VistaLINK
®
Traps ...............................................................................................................................24

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3
This page left intentionally blank

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3
REVISION HISTORY
REVISION DESCRIPTION DATE
0.1 Preliminary Version Mar 05
1.0 Updated safety section and added assembly and labeling sections Aug 05
1.1 Updated specifications Sep 05
1.2 Minor corrections throughout manual Apr 07
1.3 Updated menu structure throughout section 4.2 Apr 09
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for
the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of
Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The only warranty offered
by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is
granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation.
Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If you encounter an error,
please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in equipment design or
specifications.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3
WARNING
Never look directly into an optical fiber. Non-reversible damage to the eye can
occur in a matter of milliseconds.
"
Do not hook up the 7707MR-HD DWDM cards directly with a short fiber optic
cable. The 7707MR-HD DWDM cards produce +7dBm of power, which will
damage the receiver if connected directly.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3 Page-1
1. OVERVIEW
The 7707MR-HD is a VistaLINK
®
enabled fiber optic receiver for one HD or SD digital video signal,
accompanied by four AES audio signals, serial data, and one GPIO signal. Audio and control signals are
de-embedded from the HD, SD, or SDTi video signal that is applied to the optical input. The 7707MR-HD
is designed to operate with a companion 7707MT-HD transmitter, to permit communication over fiber optic
cable with low latency.
Monitoring and control of card status and parameters is provided locally, at the card-edge, or remotely via
VistaLINK
®
capability. The wide-band optical input of the 7707MR-HD is compatible with all available
7707MT-HD transmitter wavelengths. This card occupies one card slot and can be housed in either a 1RU
frame, which will hold up to three modules, or a 3 RU frame, which will hold up to 15 modules.
Features
•HD/SD video, AES audio, serial data, and GPIO conveniently presented in a single product.
•Provides de-embedding of audio and control signals from HD-SDI (SMPTE 292M), SD-SDI (SMPTE
259M-C), or SDTi (SMPTE 305.2M).
•With sample rate conversion enabled on the companion 7707MT-HD transmitter, transport of audio
and control signals is independent of video interruptions other than format change.
•Controllable audio output interface for balanced or unbalanced AES.
•Bi-directional serial port accommodates RS-422, RS-232, or RS-485 data.
•Serial data rates up to 153Kb/s with low latency through link.
•Comprehensive signal and status monitoring via four-digit card-edge display, or VistaLINK
®
.
•DWDM wavelengths also available (ITU-T G.694.1 compliant).
•Accepts any optical wavelength in the1270nm to 1610nm range.
•Compatible with multi-mode and single-mode fiber (dual fiber version).
•SC/PC, ST/PC, or FC/PC fiber connector options.
•Fully hot-swappable from front of frame.
•VistaLINK
®
enabled for remote monitoring and control when installed in 7700FR-C frame with 7700FC
VistaLINK
®
Frame Controller.
Several versions of the 7707MR-HD allow the user to choose the optimal function / price / performance
ratio to suit a particular application. Versions with an F2 suffix transmit and receive optical over separate
fibers. Versions with a W suffix transmit (1310nm) and receive (1550nm) on different wavelengths over a
single fiber. Versions with no suffix transmit and receive on the same wavelength (1310nm) over a single
fiber.
Table 1-1 shows some typical applications and power budget calculations for the 7707MR-HD.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Page-2 Revision 1.3
ORDERING ORDERING
INFO INFO
Multi-Mode 2 <1kM 7707MT13-HD-F2 -7dBm 7707MR13-HD-F2 -23dBm 1310nm on Tx & Rx fibers
Single Mode 2 16dB/45Km 7707MT13-HD-F2 -7dBm 7707MR13-HD-F2 -23dBm 1310nm on Tx & Rx fibers
Single Mode 1 9dB/25Km* 7707MT-HD -10dBm 7707MR-HD -19dBm 1310nm, bi-directional, one
fiber
Single Mode 1WDM 20dB/57Km 7707MT-HD-W -1dBm 7707MR-HD-W -21dBm 1310nm/1550nm, WDM, bi-
directional on one fiber
Single Mode 1CWDM 19dB/76Km** 7707MTyy-HD-F2 0dBm 7707MRxx-HD-F2 "-23dBm
Different CWDM
wavelengths for Tx & Rx
with 8 channel CWDM
Mux/Demux**
Different CWDM
wavelengths for Tx & Rx
with 8 channel CWDM
Mux/Demux**,
Single Mode 1DWDM 25dB/100Km** 7707MTDyyy-HD-F2 "+7dBm 7707MRDxxx-HD-F2 "-23dBm
Different DWDM
wavelengths for Tx & Rx
with 8 channel DWDM
Mux/Demux***
Different DWDM
wavelengths for Tx & Rx
with 8 channel DWDM
Mux/Demux***
FIBER TYPE FIBERS OPTICAL/LINK
BUDGET
TRANSMIT SIDE RECEIVE SIDE DESCRIPTIONTX
POWER Rx SENSITIVITY
Single Mode 1CWDM 24dB/96Km** 7707MTyy-HD-F2 0dBm 7707MRxx-HD-F2-H "-28dBm
Single Mode 1DWDM 30dB/120Km*** 7707MTDyyy-HD-F2 "+7dBm 7707MRDxxx-HD-F2-H "-28dBm
With >20dB return loss on fiber interface
** Assumes 8ch CWDM Mus/Demux loss of 3.5dB
***Assumes 8 Ch DWDM Mux/Demux loss of 5dB
Tx Power Rx Sensitivity are nominal values ±1dBm
Fiber loss = 0.35/0.25dB per Km @1310nm/1550nm
Table 1-1: 7707MR-HD Application Configuration

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3 Page-3
4 AES Audio
Outputs
AES
AES
Video Encoder
SMPTE 292M
SMPTE 259M-C
SMPTE 305.2M
EN500083-9
Video
Data
Deembedder
Optical
Receiver
Serial
1 Serial Data
RS-422, RS232, or RS-485
GPI
1 GPIO
General Purpose I/O
Serial
GPO
Optical
Combiner
Optical
Transmitter
Video Output
Data
Encoder
Fiber
Input
Fiber
Output
Fiber
Input/Output
(Single Fiber Versions)
(Dual Fiber-F2 Version)
(Dual Fiber-F2 Version)
VistaLINK
®
Interface
Local
Control
Local
Indication
Control/
Indication
Figure 1-1: 7707MR-HD Block Diagram

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Page-4 Revision 1.3
2. INSTALLATION
Each 7707MR-HD module comes with a companion rear plate that has two BNC connectors, a multi-pin
removable terminal block, and an SC/PC (shown), ST/PC or FC/PC optical connector. For information on
mounting the rear plate and inserting the module into the frame see section 3 of the 7700FR chapter. The
following diagram shows single-fiber and dual-fiber rear plate options.
7707MR-HD-F2
AES OUT
HD OUTPUTHD OUTPUT
SERIAL
- DI +
- DO + - A1 +- A3 +
- A2 +
- A4 +
GPIO GND
7707MR-HD
AES OUT
HD OUTPUTHD OUTPUT
SERIAL
- DI +
- DO + - A1 +- A3 +
- A2 +
- A4 +
GPIO GND
A1+
AES OUTSERIAL
- DI +
- DO + - A1 +- A3 +
- A2 +
- A4 +
GPIO GND
A2+
A1- A2-
GND GND
A3+ A4+
A3- A4-
GPI GPO
DO+ DI+
DO- DI-
Pinout Detail
Figure 2-1: 7707MR-HD Rear Plates & Pin Out
2.1.1. Electrical Signal Connections
HD OUTPUT: Reclocked, level-restored, loop-back output BNC connectors for serial digital video signals
compatible with HD-SDI (SMPTE 292M), SD-SDI (SMPTE 259M-C), and SDTi (SMPTE
305.2M) standards. See section 3.1 for video output specifications. The 7707MR-HD
maintains active output video while optical input video is not suitable for transmission
(LINK…ERR or STD…ERR condition. See section 4.2.1). In this case, active picture will
be black.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3 Page-5
AES OUTPUT: AES audio output connections of the removable terminal block. The 7707MR-HD
has four AES audio outputs, designated as A1, A2, A3, and A4. Each of these four
channels has a positive and negative terminal associated with it, and is able to
output balanced or unbalanced AES. See section 0 for details about configuring the
output type. Balanced and unbalanced audio signals are connected as follows:
Balanced - Connect positive and negative audio signals to the corresponding
positive and negative terminals of the 7707MR-HD. Signal amplitude, rise/fall times,
and impedance are automatically adjusted to match balanced AES specifications
when the output type is configured through the card-edge menu.
Unbalanced - Connect unbalanced audio signals to the positive output terminal of
the 7707MR-HD. Leave the negative output terminal unconnected. Signal
amplitude, rise/fall times, and impedance are automatically adjusted to match
unbalanced AES specifications when the output type is configured through the card-
edge menu.
See section 3.2 for AES audio output specifications.
See section 0 AES audio output type configuration instructions.
SERIAL I/O: Bi-directional serial data connections of the removable terminal block. The 7707MR-
HD accommodates one channel of RS-422, RS-232, or RS-485 serial data. Data
input connections are labeled DI, while data output connections are labeled DO.
The card must be configured for use with RS-422, RS-232, or RS-485, as described
in section 4.2.9. Serial data connections are assigned per the data type selected.
RS-422, RS-232, and RS-485 signals are connected as follows:
RS-422 - Connect positive and negative RS-422 input and output signals to the
corresponding positive and negative terminals of the 7707MR-HD. Bi-directional
data will be communicated to and from the companion 7707MT-HD.
RS-232 - Connect each RS-232 input data signal to the positive or negative DI
terminal of the 7707MR-HD. The companion 7707MT-HD will output each signal on
the corresponding positive or negative DO terminal. Likewise, serial data signals
applied to the companion 7707MT-HD will be output from the 7707MR-HD.
RS-485 - Operation with RS-485 requires that DI and DO terminals be connected
together. The DI+ terminal should be connected to the DO+ terminal, and the DI-
terminal should be connected to the DO- terminal. Connect positive and negative
RS-485 signals to the corresponding positive and negative terminals of the
7707MR-HD. Bi-directional data will be communicated to and from the companion
7707MT-HD.
See section 3.3 for serial data specifications.
See section 4.2.9 to 4.2.14. for serial data configuration instructions.
GPIO: General Purpose Input and Output connections of the removable terminal block.
The General Purpose Output is a normally-open dry-contact relay closure. The
General Purpose Input is an active-low, opto-isolated connection.
See section 3.4 and 3.5 for GPIO specifications.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Page-6 Revision 1.3
2.1.2. Optical Signal Connections
For details about link operation, see sections 4.1 and 4.2.
2.1.2.1. Single Fiber Version
FIBER I/O: This is the optical input/output of the single-fiber 7707MR-HD version of the module. The
connector is a female SC/PC (shown), ST/PC, or FC/PC connector as specified at the time
of purchase. This input/output should be connected to the FIBER I/O connector of a
companion single-fiber 7707MT-HD module with a suitable fiber optic cable.
Single-fiber versions of the 7707MR-HD are designed to work with single-mode fiber optic
cable. Single fiber 7707MR13-HD versions use 1310nm wavelengths. Single fiber
7707MR13M-HD-W versions transmit and receive on 1310nm and 1550nm wavelengths
respectively.
The optical output can be configured to operate in continuous or discontinuous mode as
described in section 4.2.6. If discontinuous mode is selected, while the optical input to the
7707MR-HD is invalid (LINK…LOS condition, section 4.2.1) then this optical output will be
disabled. If continuous mode is selected, while the optical input is invalid then this optical
output will contain invalid information, but will still output.
2.1.2.2. Dual Fiber Versions
FIBER IN: This is the optical input to the dual-fiber 7707MR-HD-F2 version of the module. The
connector is a female SC/PC (shown), ST/PC, or FC/PC connector as specified at the time
of purchase. This input should be connected to the FIBER OUT connection of a companion
dual-fiber 7707MT-HD-F2 module with a suitable fiber optic cable. The dual fiber 7707MR-
HD-F2 version accepts input wavelengths from 1270nm to 1610nm, accommodating
standard, CWDM or DWDM transmission schemes. When connected directly to a
companion dual-fiber module, the 7707MR-HD-F2 is compatible with multi-mode fiber optic
cable. If not connected directly (i.e. connected through CWDM, DWDM, WDM, or
splitter/combiner) the 7707MR-HD-F2 is compatible only with single-mode fiber optic cable.
FIBER OUT This is the optical output of the dual-fiber 7707MR-HD-F2 version of the module. The
connector is a female SC/PC (shown), ST/PC, or FC/PC connection as specified at the time
of purchase. This optical output is available in 1310nm, 1550nm, and up to sixteen CWDM
wavelengths (ITU-T G.694.2 compliant). This output should be connected to the FIBER IN
connector of a companion dual-fiber 7707MT-HD-F2 module with a suitable fiber optic
cable. The output wavelength is marked on the rear panel of each 7707MR-HD-F2. When
connected directly to a companion dual-fiber module, the 7707MR-HD-F2 is compatible
with multi-mode fiber optic cable. If not connected directly (i.e. connected through CWDM,
DWDM, WDM, or splitter/combiner) the 7707MR-HD-F2 is compatible only with single-
mode fiber optic cable. The optical output can be configured to operate in continuous or
discontinuous mode as described in section 4.2.6.
If discontinuous mode is selected, while the optical input to the 7707MR-HD is invalid
(LINK…LOS condition, section 4.2.1) then this optical output will be disabled. If continuous
mode is selected, while the optical input is invalid then this optical output will contain invalid
information, but will still output.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3 Page-7
2.2. CARE AND HANDLING OF OPTICAL FIBER
2.2.1. Safety
!
CLASS 1 LASER PRODUCT
Background colour: yellow
Triangular band: black
Symbol: black
2.2.2. Assembly
Assembly or repair of the laser sub-module is done only at Evertz facility and performed only by qualified
Evertz technical personnel.
2.2.3. Labeling
Certification and Identification labels are combined into one label. As there is not enough room on the
product to place the label it is reproduced here in the manuals.
•There is no date of manufacture on this label as it can be traced by bar code label placed on the
Printed circuit board of each Evertz plug-in module
•The Model number is one of: 7707MR13-HD, 7707MR13L-HD-W, 7707MR13-HD-F2
7707MRxx-HD, (xx = 27, 29, 31, 33, 35, 37, 43, 45, 47, 49, 51, 53, 55, 57, 59, 61)
7707MRDyyy-HD (Dyyy represents ITU Grid Channel: D200, D210, D220, D230, D240, D250,
D260, D270, D280, D290, D300, D310, D320, D330, D340, D350, D360, D370, D380, D390,
D400, D410, D420, D430, D440, D450, D460, D470, D480, D490, D500, D510, D520, D530,
D540, D550, D570, D580, D590, D600)
Figure 2-2: Reproduction of Laser Certification and Identification Label

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Page-8 Revision 1.3
2.2.4. Handling and Connecting Fibers
"
Never touch the end face of an optical fiber. Always keep dust caps on optical fiber
connectors when not connected and always remember to properly clean the optical
end face of a connector before making a connection.
The transmission characteristics of the fiber are dependent on the shape of the optical core and therefore
care must be taken to prevent fiber damage due to heavy objects or abrupt fiber bending. Evertz
recommends that you maintain a minimum bending radius of 5 cm to avoid fiber-bending loss that will
decrease the maximum attainable distance of the fiber cable. The Evertz fiber optic modules come with
cable lockout devices, to prevent the user from damaging the fiber by installing a module into a slot in the
frame that does not have a suitable I/O module. For further information about care and handling of fiber
optic cable see section 3 of the Fiber Optics System Design section of this manual binder.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3 Page-9
3. SPECIFICATIONS
3.1. SERIAL DIGITAL VIDEO OUTPUT
Number of Outputs: 2
Standards: SMPTE 292M (HD-SDI), SMPTE 259M-C (SD-SDI), SMPTE305.2M (SDTi)
Connector: BNC per IEC 61169-8 Annex A
Signal Level: 800mV Nominal
DC Offset: 0V ±0.5V
Rise Fall Time: 150ps nominal @1.485Gb/s
600ps nominal @270Mb/s
Overshoot: <10% of amplitude
Return Loss: >15dB up to 1.5Gb/s
Wide Band Jitter: <0.2UI
3.2. AES AUDIO OUTPUTS
Number of Signals: 4 (user selectable for balanced or unbalanced)
Standards: AES3-2003 (Balanced AES), SMPTE 276M (Unbalanced AES)
Connector: 12 pin removable terminal strip
Sampling Rate: 48KHz
Resolution: up to 24 bits
Signal Level:
Balanced: 1Vp-p ±0.1V
Unbalanced: 2Vp-p ±0.1V Differential
Rise/Fall Times:
Balanced: 20ns ±5ns
Unbalanced: 35ns ±5ns
Return Loss: > 15dB to 6MHz
Wideband Jitter: < 10nsp-p, with conditions of minimum to maximum cable length
Latency:
SRC enabled: <
6ms @48KHz, < 9ms @32KHz
SRC disabled: <
4ms @48KHz, < 6ms @32KHz
Impedance:
Balanced: 110Ω
Unbalanced: 75 Ω
3.3. SERIAL DATA
Number of Signals: 1 input/output
Connector at Breakout: Multi-pin Removable Terminal Block
Signal Type: RS-422, RS-232, or RS-485 (selectable)
Input Termination: High impedance
Input Failsafe Bias: 5KΩto 5V on DI+ (selectable)
Baud Rate: Up to 153Kb/s (selectable

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Page-10 Revision 1.3
3.4. GENERAL PURPOSE INPUTS
Number of Signals: 1 Input
Connector at Breakout: Multi-pin Removable Terminal Block
Type: Opto-isolated, Active low
Input Voltage:
Safe Voltage Range: -20V to +10V
Off Condition (min): +3.5V
On Condition (max): +2.5V(active low)
Input Current (min): 1mA
Input Current (max): 10mA(internally limited)
3.5. GENERAL PURPOSE OUTPUTS
Number of Signals: 1 GPO Outputs, 1 Common Reference (GPO COMMON)
Connector at Breakout: Multi-pin Removable Terminal Block
Output Type: Dry contact relay closure to GPO COMMON, normally open
Output Current (min): 100mA
3.6. OPTICAL INPUTS/OUTPUTS
Number of Outputs: 1 (Single fiber version)
2 (Dual fiber version)
Connector: Female SC/PC, ST/PC or FC/PC
Return Loss: > 14 dB
Rise and Fall Time: 200 ps nominal
Wide Band Jitter: < 0.20UI
Fiber Size: 9µm core / 125 µm overall
Input Optical Sensitivity: See Table 1-1
Wavelengths:
Standard: 1310nm, 1550nm (nominal)
CWDM: 1270nm to 1610nm (See ordering information)
DWDM: C-Band/L-Band (ITU-T G.694.1 compliant)
Output Power:
1310nm FP: -7dBm ±1dBm
CWDM: 0dBm ±1dBm
DWDM: +7dBm ±1dBm
3.7. ELECTRICAL
Voltage: +12VDC
Power:
Non-DWDM: 9W
DWDM: 12W
3.8. PHYSICAL
7700 or 7701 frame mounting
Number of slots: 1

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3 Page-11
4. STATUS INDICATORS AND DISPLAYS
The 7707MR-HD has 7 LED Status indicators and a 4 digit alphanumeric display on the front card edge to
show operational status of the card at a glance. The card edge pushbutton is used to select various
displays on the alphanumeric display. Figure 4-1 shows the locations of the indicators and pushbutton.
FRAME STATUS
ON/OFF
/ MODULE OK
LOCAL FAULT
SERIAL
RUN/UPGRADE
SERIAL
LED 2
LED 3
LED 4
LED 5
LED 6
LED 7
LED 8
LINK STATUS
AUDIO 1 STATUS
AUDIO 2 STATUS
AUDIO 3 STATUS
AUDIO 4 STATUS
SERIAL IN STATUS
SERIAL OUT STATUS
Figure 4-1: Location of Status Indicators and Jumpers
4.1. STATUS INDICATOR LEDS
Two large LEDs at the front card-edge indicate operational health of the module as follows:
MODULE OK: This green LED indicates good module health. It will be on while a valid signal is
present at the video input, the output laser is operating properly, and the card power
is good.
LOCAL FAULT: This red LED indicates poor module health. Three conditions could cause this fault
indication to be active: No valid signal is present at the video input, operation of the
output laser is erroneous, or if a card power fault exists (i.e. a blown fuse). The
LOCAL FAULT indication can also be reported to the frame by setting the FRAME
STATUS jumper.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Page-12 Revision 1.3
There are seven small LEDs on the back of the card-edge that indicate signal presence. Some of these
LEDs are Bi-colour, and able to illuminate as red, or green. The functions of these LEDs are as follows:
LED 2, LINK STATUS: This LED indicates the status of the Fiber Input. When a valid optical input signal
is detected the LED will be green. When CRC errors are detected within the input video signal
(with error detection enabled, see section 4.2.15) the LED will flash red. If no valid optical
signal is detected on the fiber input of the 7707MR-HD the LED will remain off.
LED 3, AUDIO 1 STATUS: This LED indicates the status of Audio Output 1. When a valid output audio
signal is detected the LED will be green. If no audio is detected on the first audio output of the
7707MR-HD the LED will remain off.
LED 4, AUDIO 2 STATUS: This LED indicates the status of Audio Output 2. When a valid output audio
signal is detected the LED will be green. If no audio is detected on the first audio output of the
7707MR-HD the LED will remain off.
LED 5, AUDIO 3 STATUS: This LED indicates the status of Audio Output 3. When a valid output audio
signal is detected the LED will be green. If no audio is detected on the first audio output of the
7707MR-HD the LED will remain off.
LED 6, AUDIO 4 STATUS: This LED indicates the status of Audio Output 4. When a valid output audio
signal is detected the LED will be green. If no audio is detected on the first audio output of the
7707MR-HD the LED will remain off.
LED 7, SERIAL IN STATUS: This LED indicates the status of the Serial input data. When a valid input
data signal is detected the LED will be green. When parity errors are detected (with error
detection enabled, and parity information present) the LED will flash red. If no data is detected
on the serial data input of the 7707MR-HD the LED will remain off.
LED 8, SERIAL OUT STATUS: This LED indicates the status of Serial output data. When a valid output
data signal is detected the LED will be green. If no output serial data is detected the LED will
remain off.
4.2. DOT MATRIX DISPLAY
Additional signal and status monitoring is provided via the 4-digit dot-matrix display located at the card-
edge. The card-edge pushbutton and toggle-switch are used to navigate through the display menu. Figure
4-2 provides a quick reference to the display menu structure.
The most recent user selection will be maintained in non-volatile memory in the event of power
loss to the module.

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Revision 1.3 Page-13
Selections Per Table
LASR...ERR (Laser Error)
Supersedes
LINK...LOS (Fiber-Link Loss)
Supersedes
OK (Ay-Okay)
BACK (Abort)
Pushbutton Ö
Menu Level 1 Menu Level 2 Menu Level 3
Indications
CTRL (Control)
Selections
×
Toggle
Switch
Ø
STAT (Status)
PWR (Optical Power) -1 to -40 (dBm Value)
Indications
VER (Software Version) Software Version
Indications
AUD1 (Audio 1)
Selections
AUD2 (Audio 2)
JACK (Monitor Jack) AUD3 (Audio 3)
AUD4 (Audio 4)
Selections
FRST(Factory Reset)
BACK (Abort)
DISP (Display Orientation)
VERT (Vertical)
HORZ (Horizontal)
Selections
YES (Accept)
NO (Abort)
Menu Level 4
FIN (Fiber-Link Input)
OVR (power over max)
FREE (Group Unused)
USED (Group Used)
Indications
LOS (Loss of Video)
GRP1 (Audio Group 1)
GRP2 (Audio Group 2)
GRP3 (Audio Group 3)
GRP4 (Audio Group 4)
Selections Selections
STD (Video Standard) Standards Per Table
LOS (Loss of VIdeo)
HCLN (Output Hanc Cleaning) ON (Clean Output Hanc)
OFF (Pass Output Hanc)
Selections
EDET (Error Detection) FIN (Fiber-Link Input) ON (Indicate Errors to LED)
OFF (Disable Error Indication)
Selections
VOL (Volume) 0to 64 (Arbitrary Range)
CHAN (Audio Channel)
Selections
Selections
Indications
TYPE (Data Type)
232 (RS-232)
422 (RS-422)
Selections
SER (Serial Data) RATE (Baud Rate) Selections
Selections
485 (RS-485)
A1+2 (AES1 and AES2)
A3+4 (AES3 and AES4)
Selections
EMBD (De-embedding)
SER (Serial Data)
LN1 (Vanc Embed Line 1)
LN2 (Vanc Embed Line 2)
Selections
0 (Line 0) to 2047 (line 2047)
Selections
Selections
DID (Data ID) 50 (DID=50) to 5F (DID=5F)
Selections
1 (SDID=1) to FF (SDID=FF)
Selections
SDID (Secondary Data ID)
GPIO (GPIO Data)
LN (Vanc Embed Line)
Selections
DID (Data ID) 50 (DID=50) to 5F (DID=5F)
Selections
1 (SDID=1) to FF (SDID=FF)
Selections
SDID (Secondary Data ID)
Menu Level 5
NONE (Don't Embed Line 1)
0 (Line 0) to 2047 (line 2047)
NONE (Don't Embed Line 2)
Selections
0 (Line 0) to 2047 (line 2047)
NONE (Don't Embed)
Selections
GRP1 (Audio Group 1)
GRP2 (Audio Group 2)
GRP3 (Audio Group 3)
GRP4 (Audio Group 4)
NONE (Don't De-embed)
Selections
TERM (Termination)
BAL (Balanced 100Ω)
UBAL (Unbalanced 75Ω)
Selections
AES1 (AES Output 1)
AES2 (AES Output 2)
AES3 (AES Output 3)
AES4 (AES Output 4)
Selections
LASR (Laser Enable Mode) CONT (Continuous)
DISC (Discontinuoust)
Selections
FOUT (Fiber-Link Output)
BIAS (Failsafe Bias) ON (Bias On)
OFF (Bias Off)
Selections
Selections
LOW (power under min)
Figure 4-2: Card Edge Menu Structure

7700 Multi-Frame Manual
7707MR-HD Multi-Signal HD/SD, AES, and Control Fiber Receiver
Page-14 Revision 1.3
4.2.1. Display Warning Status Indications
Upon entering menu level 1 on power up, or following a configuration selection, the default display
selection will indicate the warning status of the 7707MR-HD. This warning status indication can also be
entered while already in menu level 1, by using the toggle switch. During normal operation, while no
warnings conditions are active, the OK indication will be displayed. Three warning indications can
supersede this display state. The following list describes possible indications for this menu item, listed in
order of display priority:
LASR…ERR Laser Error Warning. Flashing indication alternates between LASR and ERR
LINK…LOS Video Loss of Optical Signal. Flashing indication alternates between LINK and LOS
OK Okay. No warning conditions are active
4.2.2. Displaying the Video Standard
The card-edge display of the 7707MR-HD can report the signal standard present at the fiber optic input.
To indicate the input video standard, select the STAT (Status) menu item in menu level 1, followed by FIN
(Fiber Input) and STD (Video Standard) menu items.
STAT
FIN
STD
1080i/60
1080i/59.94
1080i/50
1035i/60
1035i/59.94
1080i/48
1080i/47.96
720p/60
720p/59.94
NTSC
PAL
LOS
1080i/60 1080i/60 standard is present
1080i/59.94 1080i/59.94 standard is present
1080i/50 1080i/50 standard is present
1035i/60 1035i/59.94 standard is present
1035i/59.94 1035i/59.94 standard is present
1080i/48 1080i/48 standard is present
1080i/47.96 1080i/47.96 standard is present
720p/60 720p/60 standard is present
720p/59.94 720p/59.94 standard is present
NTSC NTSC standard is present
PAL PAL standard is present
LOS Loss of signal. No valid video signal is detected at the
fiber input.
4.2.3. Displaying the Status of Input Video Embedded Audio Groups
The 7707MR-HD allows the user to monitor the status of input video embedded audio groups. This allows
for easy identification of active groups. To view the current status of input video embedded audio groups,
select the STAT (Status) menu item in menu level 1, followed by the FIN (Fiber Input) and GRP1, GRP2,
GRP3 or GRP4 (Audio Groups 1 through 4) menu items.