evertz MultiFrame 7807LR-2 User manual

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
TABLE OF CONTENTS
1. OVERVIEW ............................................................................................................................................1
2. INSTALLATION .....................................................................................................................................3
2.1. 7807LR-2/7807LR-2-H CONNECTIONS .....................................................................................4
2.2. CARE AND HANDLING OF OPTICAL FIBER ............................................................................5
2.2.1. Handling and Connecting Fibers.......................................................................................5
3. 7807LR-2/7807LR-2-H SPECIFICATIONS...........................................................................................6
3.1. RF OUTPUTS................................................................................................................................6
3.2. OPTICAL INPUTS.........................................................................................................................6
3.3. GENERAL PURPOSE OUTPUTS ...............................................................................................6
3.4. ELECTRICAL................................................................................................................................6
3.5. PHYSICAL.....................................................................................................................................6
4. STATUS INDICATORS AND DISPLAYS .............................................................................................7
4.1. 7807LR-2/7807LR-2-H STATUS INDICATORS..........................................................................7
5. JUMPER POSITIONS............................................................................................................................8
5.1. 7807LR-2/7807LR-2-H JUMPERS AND LEDS...........................................................................8
5.2. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED BY THE
GLOBAL FRAME STATUS..........................................................................................................8
5.3. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES................................................9
5.4. FACTORY AND BDM JUMPERS ................................................................................................9
5.5. GPO JUMPERS............................................................................................................................9
6. DOT-MATRIX DISPLAY ......................................................................................................................10
6.1. 7807LR-2/7807LR-2-H CONTROLLED PARAMETERS ..........................................................15
6.1.1. Adjusting the Optical Power Alarm Thresholds...............................................................15
6.1.2. Adjusting the RF Output Power Alarm and Squelch Thresholds....................................15
6.1.3. Selecting the Output Gain Mode.....................................................................................16
6.1.4. Adjusting the RF Output Gain .........................................................................................17
Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
6.1.5. Adjusting the AGC Target Level......................................................................................17
6.1.6. Enabling/Disabling Squelch Mode...................................................................................18
6.1.7. Setting the Card Edge Display Orientation......................................................................18
6.1.8. Resetting Factory Defaults ..............................................................................................18
6.2. TRANSMITTER CONTROLLABLE PARAMETERS.................................................................18
6.2.1. Adjusting the RF Input Power Alarm Thresholds............................................................19
6.2.2. Adjusting the Internal Transmitter Temperature Alarm Thresholds................................19
6.2.3. Adjusting the Input Voltage Alarm Thresholds................................................................20
6.2.4. Adjusting the LNB Current Alarm Thresholds.................................................................20
6.3. 7807LR-2/7807LR-2-H MONITORED CONDITIONS AND PARAMETERS ............................21
6.3.1. Displaying the Input Optical Power..................................................................................21
6.3.2. Displaying the Output RF Power .....................................................................................21
6.3.3. Displaying the Squelch Status.........................................................................................21
6.4. TRANSMITTER MONITORED PARAMETERS.........................................................................22
6.4.1. Displaying the Presence of the Data Signal....................................................................22
6.4.2. Displaying the Input RF Power to the Connected Transmitter........................................23
6.4.3. Displaying the Gain Mode of the Connected Transmitter...............................................23
6.4.4. Displaying the Gain Level of the Connected Transmitter................................................23
6.4.5. Displaying the AGC Status of the Connected Transmitter..............................................24
6.4.6. Displaying the RF Drive Status of the Connected Transmitter.......................................24
6.4.7. Displaying the Output Optical Power of the Connected Transmitter ..............................24
6.4.8. Displaying the Laser Status of the Connected Transmitter.............................................25
6.4.9. Displaying Status of the Power Supply Connected to the Transmitter...........................25
6.4.10. Displaying the Internal Temperature of the Connected Transmitter...............................25
6.4.11. Displaying the LNB Mode of the Connected Transmitter................................................26
6.4.12. Displaying the LNB Voltage of the Connected Transmitter ............................................26
6.4.13. Displaying the LNB Current.............................................................................................26
6.4.14. Displaying the Firmware Version of the Connected Transmitter ....................................27
6.4.15. Displaying the Model of the Connected Transmitter.......................................................27
7. VISTALINK®REMOTE MONITORING/CONTROL............................................................................28
7.1. WHAT IS VISTALINK®?..............................................................................................................28
7.1.1. VISTALINK®Monitored Parameters................................................................................29
7.1.2. VISTALINK®Controlled Parameters...............................................................................29
7.1.3. VISTALINK®Traps...........................................................................................................30
Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
Figures
Figure 1-1: 7807LR-2/7807LR-2-H Block Diagram........................................................................................... 2
Figure 2-1: 7807LR-2/7807LR-2-H Rear Panel ................................................................................................ 3
Figure 5-1: Location of 7807LR-2/7807LR-2-H Jumpers and LEDs.................................................................. 8
Figure 6-1: Card Edge Menu Structure.......................................................................................................... 14
Tables
Table 7-1: VistaLINK®Monitored Parameters................................................................................................ 29
Table 7-2: VistaLINK®Controlled Parameters................................................................................................ 30
Table 7-3: VistaLINK®Traps.......................................................................................................................... 30
Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 Initial Release July 2011
1.1 Updated specifications, corrections Sept 2011
1.2 Updated rear panel and block diagrams June 2014
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for
the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of
Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The only warranty
offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty
is granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order
confirmation. Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If you
encounter an error, please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in
equipment design or specifications.
Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
WARNING
!
Do not connect the 7807LR-2 without optical attenuation to a transmitter producing in
excess of +3dBm optical power. Maximum optical input to the 7807LR-2 is +3dBm –
more power than this may damage the receiver.
!
Do not connect the 7807LR-2-H without optical attenuation to a transmitter producing
in excess of –7dBm optical power. Maximum optical input to the 7807LR-2-H is -7dBm
– more power than this may damage the receiver.
Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
This page left intentionally blank
Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
1. OVERVIEW
The 7807LR-2 and 7807LR-2-H Fiber Optic Receivers are used for receiving RF signals transported
optically over fiber optic cable by a companion transmitter. They accept two optical inputs and provide two
pairs of electrical outputs. Individual monitoring and control is provided for each signal path. Gain may be
adjusted manually in 0.5dB increments or managed automatically via AGC or IGC modes. SmartMON™
capability decodes and displays incoming information from the paired SmartMON™ enabled companion
transmitter.
Two versions of the card are available, including the 7807LR-2 which has standard-sensitivity receivers,
and the 7807LR-2-H which utilizes high-sensitivity receivers for medium/long-haul applications. With two
optical receivers per single-slot card, the 7807LR-2 and 7807LR-2-H provide an economical and high
density solution.
Features:
•Extended frequency response for extended L-Band off-air DTV and other signals
•Protocol independent design - transports all modulation formats
•Supports manual, automatic (AGC), and intelligent (IGC) gain control modes
•IGC mode provides simple automatic compensation for fiber loss while output level tracks LNB level
input at SmartMON™ capable fiber transmitter
•0.5dB gain adjustment granularity for setting manual gain or AGC target power levels
•Dual, full power outputs provided from each input to facilitate signal distribution or monitoring
•Dual fiber receivers on a single-slot card provides the industry’s highest density solution
•The 7807LR-2-W is a dual channel card that features and on-board fiber WDM, requiring only a single fiber for
the link (companion transmitter is the 7807LT13/15-2-W)
•Fully hot-swappable from front of frame
•SmartMON™ capability for display of monitored parameters from companion SmartMON™ capable
fiber transmitters
•VistaLINK® capability is available for monitoring and control when modules are used in a 3RU
7800FR frame and a 7700FC VistaLINK®frame controller is installed in slot 1 of the frame
•Form-C dry contact GPO alarm contacts for monitoring
•Fiber link provides electrical isolation between antenna and facility, mitigating ground loop and
lightning issues
•Compatible with all 2408LT, 7706LT, 7708LT and 7807LT-2
•Wide range optical inputs (1270nm to 1610nm)
•Supports single-mode and multi-mode fiber optic cable
•Available with SC/UPC, ST/UPC, FC/UPC, SC/APC and FC/APC connector options
•The 7807LR-2/7807LR-2-H occupies one card slot and can be housed in a
•1RU frame that will hold up to 3 modules, a 7800FR 3RU frame that will hold
•up to 15 modules, or a standalone enclosure which holds 1 module
Revision 1.2 Page - 1

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
Optical
Receiver Splitter
RF Output
1A
RF Output
1B
RF
AMP
Monitoring &
Control
VistaLINK
Interface
TM
LED Indicators
Dot Matrix Display
Toggle Switch/
pushbutton
RF
AMP
RF
AMP
Optical
Receiver Splitter
RF Output
2A
RF
AMP RF
AMP
RF
AMP
RF Output
2B
Fiber
Input 1
Fiber
Input 2
WDM
(7807LR-2-W
version Only)
Fiber
Input
Figure 1-1: 7807LR-2/7807LR-2-H Block Diagram
Page - 2 Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
2. INSTALLATION
The 7807LR-2/7807LR-2-H comes with a companion rear plate appropriate for a 1RU, 3RU or standalone
enclosure as specified at the time of order. SC/UPC, SC/APC, ST/UPC, FC/UPC or FC/APC optical
connectors are available and the type specified at the time of order will be installed. For information on
mounting the rear plate and inserting the module into the frame, see the 7700/7800FR manual for detailed
instructions.
7807LR-2-W
7807LR-2
Figure 2-1: 7807LR-2/7807LR-2-W Rear Panel
Revision 1.2 Page - 3

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
2.1. 7807LR-2/7807LR-2-H CONNECTIONS
FIBER INPUTS: SC/UPC, SC/APC, ST/UPC, FC/UPC or FC/APC female connectors. This
connector should be connected with suitable fiber optic cables to the optical outputs
of an appropriate transmitter at the origin. The standard connector type is UPC.
This connector type is compatible with standard PC connectors, but for optimal
return loss performance, Evertz recommends the use of UPC fiber terminations
throughout the system. The optional APC connectors provide further enhanced
return loss performance, and when specified, should also be used throughout the
system.
RF OUT:Two electrical output connectors for each received RF signals. The dual connectors
provide an extra connector for monitoring or further distribution.
GPO’s: The 3 pin terminal strip is used for the General Purpose Outputs (GPO). Pin1 and
Pin2 refer to GPO1 and GPO2 respectively, whose behavior (NC/NO) can be
selected by a jumper. (Refer to section 5.1 for Jumper Positions). Signal on GPO
Common (C) is to be provided by the user. A minor alarm between Common and
GPO1 is triggered in a state of RF exceeding threshold and major alarm between
Common and GPO2 is triggered in a state of no optical power. Each GPO output is
a set of normally open and normally closed relay contacts as shown in Figure 2-2.
NO GPO Contact
GPO Common
from
internal
circuit
NC GPO Contact
Figure 2-2: GPO Configuration

Please note:
Unused connectors should be terminated with appropriate loading (50 or 75
Ohm).
Page - 4 Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
2.2. CARE AND HANDLING OF OPTICAL FIBER
2.2.1. Handling and Connecting Fibers

Never touch the end face of an optical fiber. Always keep dust caps on optical fiber
connectors when not connected and always remember to properly clean the optical end
facet of a connector before making a connection.
The transmission characteristics of the fiber are dependent on the shape of the optical core and therefore
care must be taken to prevent fiber damage due to heavy objects or abrupt fiber bending. Evertz
recommends that you maintain a minimum bending radius of 5 cm to avoid fiber-bending loss that will
decrease the maximum attainable distance of the fiber cable. Evertz fiber optic modules come with cable
lockout devices to prevent the user from damaging the fiber by installing a module into a slot in the frame
that does not have a suitable rear plate installed.
Revision 1.2 Page - 5

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
3. 7807LR-2/7807LR-2-H SPECIFICATIONS
3.1. RF OUTPUTS
Number of Outputs: 2 + 2 (two per optical input)
Connector: BNC per IEC 61169-8 Annex A (F type optional)
Output Impedance: 75 Ω(50 Ωoptional)
Return Loss: >15dB
Frequency Range: 100MHz–2800MHz
Output IP3: +28dBM
AGC Mode: -10 to –40dBm (within AGC range)
Manual or IGC Mode: -10 to –65dBm (depends on the RF input level, gain setting and optical loss)
IGC/AGC Hold Range: -10 to +30dB

For detailed link performance specifications, see the
Specifications section of the
accompanying transmitter.
3.2. OPTICAL INPUTS
Number of Inputs: 2
Connector: Female SC/UPC, SC/APC, ST/UPC, FC/UPC, FC/APC
Operating Wavelength: 1270nm - 1610nm
Optical Sensitivity:
7807LR-2: -14 dBm with ≥35dB CNR*
7807LR-2-H: -20 dBm with ≥35dB CNR*
Maximum Input Power:
7807LR-2: +3dBm
7807LR-2-H: -7dBm
•Tested 36MHz BW source, CNR > 35dB at the transmitter.
3.3. GENERAL PURPOSE OUTPUTS
Number of Outputs: 2
Type: Dry relay contacts - NO and NC contact provided
Connector: 3 pin removable terminal strip
3.4. ELECTRICAL
Voltage: +12VDC
Power: 6 Watts
GPO Common: +12VDC, 250mA ( Max switching Voltage and Current)
EMI/RFI: Complies with FCC regulations for class A devices, Complies with EU EMC
directive 89/336/EEC.
3.5. PHYSICAL
7800, 7701 and S7701 frame mounting:
Number of slots: 1
Page - 6 Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
4. STATUS INDICATORS AND DISPLAYS
4.1. 7807LR-2/7807LR-2-H STATUS INDICATORS
The 7807LR-2/7807LR-2-H has ten LED status indicators on the front card edge to show operational
status of the card at a glance. See Figure 5-1 for LED locations.
Two large LEDs on the front of the board indicate the general health of the module:
LOCAL FAULT: This red LED indicates poor module health and will be on during the
absence of a valid optical input signal or if a local internal power fault exists
(i.e.: a blown fuse). Whether or not this LOCAL FAULT indication is reported
to the frame may be selected by the FRAME STATUS jumper (see section
5.1).
MODULE OK: This green LED indicates good module health. It will be on when a valid
optical input signal is present, and the board power is good.
There are 8 small LEDs that indicate the status of the output RF signal, and optical input signal.
OPTICAL INPUT STATUS
CH1/CH2:These LEDs will be yellow, respectively, when input optical powers on CH1
and CH2 are lower than or equal to the optical power low threshold settings.
These will be green when the input optical powers are within threshold
settings. These will be red when the input optical powers are higher than or
equal to the optical power high threshold settings.
RF STATUS CH1/CH2:These LEDs will be red, respectively, when the output RF signals on CH1
and CH2 are higher than or equal to threshold settings. These will be green
when the output RF signals are within RF threshold settings. These will be
yellow when the output RF signals are lower than or equal to the RF low
threshold settings.
GAIN MODES CH1/CH2:These LEDs are ON when AGC or IGC mode is enabled and OFF when
Manual mode is enabled for CH1 and CH2. These will be green when power
levels are within the AGC or IGC hold range and constant RF output levels
are being maintained. These will be red if power levels are above the power
levels required for the AGC/IGC circuit to be able to maintain a constant
level. These will be yellow if power levels are below the power levels
required for the AGC/IGC circuit to be able to maintain a constant level.
SQUELCH MODE
CH1/CH2:These LEDs are ON when squelch is enabled on respective Channel.
These will be green when squelch modes are enabled but not active. These
will be red when squelch modes are enabled and the output signals are
squelched.
Revision 1.2 Page - 7

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
5. JUMPER POSITIONS
5.1. 7807LR-2/7807LR-2-H JUMPERS AND LEDS
/ MODULE OK
LOCAL FAULT
Optical Status CH1
RF Status CH1
AGC/IGC Status CH1
Squelch Status CH1
Squelch Status CH2
DOT MATRIX DISPLAY
Optical Status CH2
RF Status CH2
AGC/IGC Status CH2
RUN/UPGRADE
FRAME
STATUS
OFF/ON
J6
Serial Upgrade Port
Pushbutton
Toggle
Switch
BDM
FACTORY
GPO1
GPO2
NC/NO
NC/NO
Figure 5-1: Location of 7807LR-2/7807LR-2-H Jumpers and LEDs
5.2. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS
The FRAME STATUS jumper J3 determines whether local faults (as shown by the Local Fault indicator)
will be connected to the 7700/7800FR frame's global status bus.
FRAME STATUS:To monitor faults on this module with the frame status indicators (on the Power
Supply FRAME STATUS LEDs and on the Frame's Fault Tally output) install this
jumper in the ON position (default).
When this jumper is installed in the Off position local faults on this module will not
be monitored.
Page - 8 Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
5.3. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES
UPGRADE:The UPGRADE jumper J5 is used when firmware upgrades are being done to the module.
For normal operation it should be installed in the RUN position. See the Upgrading
Firmware section of this manual for more information.
To upgrade the firmware:
1. Pull the module out of the frame.
2. Move the UPGRADE jumper into the UPGRADE position.
3. Install the Upgrade cable provided (located in the vinyl pouch in the front of this manual) onto the
SERIAL header at the card edge.
4. Re-install the module into the frame.
5. Run the upgrade as described in the Upgrading Firmware section of this manual.
6. When the upgrade is completed, remove the module from the frame, move the UPGRADE jumper into
the RUN position, remove the upgrade cable and re-install the module.
The module is now ready for normal operation.
Note that if installed in a frame with a 7700/7800FC frame controller, the 7807LR-2/7807LR-2-H may also
be conveniently upgraded through Evertz VistaLINK PRO, without service interruption. Consult
VistaLINK®PRO documentation for details on this feature.
5.4. FACTORY AND BDM JUMPERS
When shipped from the Evertz facility, the FACTORY and BDM jumpers will not be installed. These
jumpers should not be installed for any reason. If jumpers are on these positions they should be
removed.
5.5. GPO JUMPERS
The Jumpers GPO1 and GPO2 allow user to select the behavior of Outputs of GPO’s.
In NC (Normally Closed) jumper position of GPO1, an OPEN circuit is present between C (common) pin
and pin 1 of GPO connector and in NO (Normally Open) position of GPO1 a CLOSED circuit is present
between C (common) pin and pin 1 of GPO connector.
In NC (Normally Closed) jumper position of GPO2, an OPEN circuit is present between C (common) pin
and pin 2 of GPO connector and in NO (Normally Open) position of GPO2 a CLOSED circuit is present
between C (common) pin and pin 2 of GPO connector.
Revision 1.2 Page - 9

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
6. DOT-MATRIX DISPLAY
Signal and status monitoring and control of the card’s parameters are provided via the four-digit
alphanumeric display located on the card edge. The card-edge toggle-switch (see Figure 5-1) is used to
navigate through the display menus and the push button is used to select options. Figure 6-1 provides a
quick reference to the display menu structure.
CTRL menu items have user-adjustable configuration values associated with them. STAT menu items
display operating conditions or configuration values, but do not allow adjustment.
If a specific menu selection has a configuration value associated with it, then this may be changed using
the toggle switch. Pressing the pushbutton will apply the displayed value and return you to the previous
menu level.
The most recent user selection will be maintained in non-volatile memory in the event of power
loss to the module.
Page - 10 Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
CTRL
RX
OPTH
LWR CH1 -4 to -40 dBm
Default -30 dBm
CH2 -4 to -40 dBm
Default -30 dBm
UPPR CH1 -3 to +5 dBm
Default +5 dBm
CH2 -3 to +5 dBm
Default +5 dBm
RFTH
LWR CH1 -30 to -55 dBm
Default -55 dBm
CH2 -30 to -55 dBm
Default -55 dBm
UPPR CH1 0 to -29 dBm
Default -5 dBm
CH2 0 to -29 dBm
Default -5 dBm
SQL CH1 -40 to -65 dBm
Default -60
CH2 -40 to -65 dBm
Default -60
MODE
CH1
IGC
MAN
AGC (default)
CH2
IGC
MAN
AGC (default)
GAIN
(not visible in
AGC Mode)
CH1 See notes Default 0 dB MAN -10 to -31.5dB
IGC -10 to -31.5dB
CH2 See notes Default 0 dB MAN -10 to -31.5dB
IGC -10 to -31.5dB
OUTL
(visible in AGC
Mode only)
CH1 -10 to -40 dBm Default -
20 dBm
CH2 -10 to -40 dBm Default -
20 dBm
SQL
CH1
EN
DIS (default)
CH2
EN
DIS (default)
Revision 1.2 Page - 11

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
CTRL
(continued)
TX
CH1
RFTH LWR -30 to -65 dBm
Default -65 dBm
UPPR 0 to -29 dBm
Default -5 dBm
TPTH
(visible if TX is
2408LT,2407LT
or 2407LTA)
LWR -40 to 125°C
Default 0°C
UPPR -40 to 125°C
Default 0°C
PWTH
(visible if TX is
2408LT,2407LT
or 2407LTA)
LWR 11 to 15 Volt
Default 11V
UPPR 16 to 23Volt
Default 20V
LCTH
(not visible is
TX is 2407LT
or 2407 LTA)
LWR 0 to 500mA
Default 0mA
UPPR 0 to 500mA
Default 0mA
CH2
RFTH LWR -30 to -65 dBm
Default -65 dBm
UPPR 0 to -29 dBm
Default -5 dBm
TPTH
(visible if TX is
2408LT,2407LT
or 2407LTA)
LWR -40 to 125°C
Default 0°C
UPPR -40 to 125°C
Default 0°C
PWTH
(visible if TX is
2408LT,2407LT
or 2407LTA)
LWR 11 to 15 Volt
Default 11V
UPPR 16 to 23Volt
Default 20V
LCTH
(not visible is
TX is 2407LT
or 2407 LTA)
LWR 0 to 500mA
Default 0mA
UPPR 0 to 500mA
Default 0mA
DISP
HORZ
VER (default)
FRST
YES
Factory reset
(leaves
calibration
offset alone)
NO
Page - 12 Revision 1.2

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
STAT
RX
OPWR
CH1
+7 to –40 dBm
CH2 +7 to -40 dBm
RPWR CH1 0 to -55 dBm
CH2 0 to -55 dBm
SQL
CH1
DIS
ACT
NACT
CH2
DIS
ACT
NACT
TX
CH1
TONE
present/loss
INPL
0 to -60dBm
MODE
AGC
MAN
GAIN
0-31.5
AGC
OFF
LOW
OK
HIGH
RFDR
(visible if TX is
2408LT,2407LT
or 2407LTA)
HIGH
OK
LOW
OPWR
LASR
OK
DEGR
PSU
(visible if TX is
2408LT,2407LT
or 2407LTA)
VOLT
STAT
OK
FAIL
TEMP
(visible if TX is
2408LT,2407LT
or 2407LTA)
LNB
OFF
BYP,
+13V,
+13VT,
+17V,
+17VT,
BYPT
+18V
Revision 1.2 Page - 13

7700/7800 MultiFrame Manual
7807LR-2, 7807LR-2-H Dual L-Band/Wideband RF Fiber Receiver
STAT
(continued)
TX
(continued)
LNBV
if TX 2408LT,2407LTor
2407LTA
22KT
LNBC
VER
TYPE
SER
If TX is 2408LT
CH2
TONE
present/loss
INPL
0 to -60dBm
MODE
AGC
MAN
GAIN
0-31.5
AGC
OFF
LOW
OK
HIGH
RFDR
(visible if TX is
2408LT,2407LT
or 2407LTA)
HIGH
OK
LOW
OPWR
LASR
OK
DEGR
PSU
(visible if TX is
2408LT,2407LT
or 2407LTA)
VOLT
STAT
OK
FAIL
TEMP
(visible if TX is
2408LT,2407LT
or 2407LTA)
LNBM
OFF
BYP,
+13V,
+13VT,
+17V,
+17VT,
BYPT
+18V
LNBV
22KT
LNBC
VER
TYPE
SER
If TX is 2408LT
VER
Firmware Version
Figure 6-1: Card Edge Menu Structure
Page - 14 Revision 1.2