evertz 7700 Series User manual

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0
TABLE OF CONTENTS
1. OVERVIEW.........................................................................................................................................1
2. INSTALLATION..................................................................................................................................3
2.1. OPTICAL CONNECTIONS........................................................................................................3
2.2. AES CONNECTIONS................................................................................................................4
2.3. CARE AND HANDLING OF OPTICAL FIBER..........................................................................5
3. SPECIFICATIONS..............................................................................................................................5
3.1. AES AUDIO OUTPUTS.............................................................................................................5
3.2. OPTICAL INPUT........................................................................................................................6
3.3. ELECTRICAL ............................................................................................................................6
3.4. PHYSICAL.................................................................................................................................6
4. CARD-EDGE MONITORING AND CONTROL .................................................................................6
4.1. STATUS INDICATOR LEDS.....................................................................................................7
4.2. CARD-EDGE DISPLAY AND CONTROLS...............................................................................7
4.2.1. Displaying the Optical Power.........................................................................................8
4.2.2. Displaying the AES Audio Sample Rate.........................................................................9
4.2.3. Selecting the AES Output Signal Type...........................................................................9
4.2.4. Selecting the Headphone Jack Channel and Volume..................................................10
5. JUMPER CONTROLS......................................................................................................................10
5.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS.......................................................................................10
5.2. FIRMWARE VERSIONS THAT ALLOW CARD TO BE CONTROLLED BY BOTH
LOCAL CONTROLS AND THE VISTALINKTM INTERFACE SIMULTANEOUSLY.................11
5.3. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES ............................................11

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0
6. VISTALINK™ REMOTE MONITORING/CONTROL........................................................................11
6.1. WHAT IS VISTALINK™?........................................................................................................11
6.2. VISTALINK™ MONITORED PARAMETERS..........................................................................12
6.3. VISTALINK™ CONTROLLED PARAMETERS.......................................................................12
6.4. VISTALINK™ TRAPS .............................................................................................................12
Figures
Figure 1–1: 7707AR Block Diagram.................................................................................................................... 2
Figure 2–1: 7707AR Rear Panels....................................................................................................................... 3
Figure 2–2: 7707AR-8U-DB Pin Out................................................................................................................... 4
Figure 4–1: Location of Status Indicators and Jumpers ..................................................................................... 7
Figure 4–2: Card-edge Menu Quick Reference.................................................................................................. 8
Tables
Table 1: Typical Application Configurations........................................................................................................ 1
Table 2: Firmware for simultaneous local and remote control.......................................................................... 11
Table 3: VistaLINK™ Monitored Parameters.................................................................................................... 12
Table 4: VistaLINK™ Controlled Parameters ................................................................................................... 12
Table 5: VistaLINK™ Traps............................................................................................................................... 12

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0
REVISION HISTORY
REVISION DESCRIPTION DATE
0.1 Preliminary version Jul 03
0.2 Updated specifications and rear panel drawings Aug 03
0.3 Updated information on connecting unbalanced AES signals Sep 03
Revised rear panel drawing of 8U version.
0.4 Removed control jumper reference and added firmware versions that support Sep 04
simultaneous local and remote control. Updated sections 4.2.1, 4.2.3, 5.2
and tables 3, 4, 5 for updated monitored / controlled parameters and traps.
1.0 Added
7707AR-8U-DB and updated laser warnings Aug 05
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for
the rights of third parties, which may be effected in any way by the use thereof. Any representations in this document concerning performance of
Evertz products are for informational use only and are not warranties of future performance, either express or implied. The only warranty offered by
Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is
granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation.
Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If you encounter an error,
please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in equipment design or
specifications.

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0
WARNING
Never look directly into an optical fiber. Non-reversible damage to the eye can
occur in a matter of milliseconds.

Do not hook up the 7707AT DWDM cards and 7707AR cards directly with a short
fiber optic cable. The 7707VAT DWDM card produces +7dBm of power which will
damage the receiver if connected directly.

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0 7707AR-1
1. OVERVIEW
The 7707AR AES Receiver extends multiple channels of AES audio over a single fiber optic link. The
7707AR-8U version interfaces to 8 channels of unbalanced AES, the 7707AR-8U-DB has DB-25
connections for unbalanced audio that are backwards compatible with 7705AR-8, and the 7707AR-8
version accommodates unbalanced or balanced AES. The 7707AR-16 is a version that interfaces to 16
channels of unbalanced or balanced AES. Each 7707AR version is designed to operate with a companion
7707AT AES Transmitter, to permit communication over distances up to 50Km, with minimum possible
latency.
Monitoring and control of card status and parameters is provided locally, at the card-edge, or remotely via
VistaLINKTM capability.The 7707AR provides a wide-band optical input, which is compatible with standard,
CWDM, or DWDM transmission schemes.
Features:
• Accommodates eight or sixteen AES audio signals.
• 7707AR-8 and 7707AR-16 versions provide interface to balanced or unbalanced signals.
• 7707AR-8U version provides interface to unbalanced signals via convenient BNC connections.
• 7707AR-8U-DB has DB-25 connections for unbalanced audio that are backwards compatible with
7705AR-8
• AES audio sample rate detection is provided independently for each channel.
• Additional audio monitoring via card-edge headphone jack with adjustable volume.
• All configuration settings are controllable through the card-edge user interface, or VistaLINKTM.
• Comprehensive signal and status monitoring via four-digit card-edge display, or VistaLINKTM.
• Wide-band optical input is compatible with standard, CWDM, or DWDM transmission schemes.
• Compatible with multi-mode and single-mode fiber.
• SC/PC, ST/PC, or FC/PC fiber connector options.
• Fully hot swappable from front of frame.
• VistaLINKTM enabled for remote monitoring and control when installed in 7700FR-C frame with
7700FC VistaLINK™ Frame Controller.
Transmit Side Receive Side
Fiber Type Optical/Link Budget Ordering
Product Info TX Power Ordering Product Info RX Sensitivity Description
Multi-Mode < 3km 7707AT13-8U 7707AT13-8
7707AT13-16 -7dBm 7707AR-8U
7707AR-8
7707AR-16 -28dBm 1310nm Wavelength
Single-Mode 21dB/50km 7707AT13-8U 7707AT13-8
7707AT13-16 -7dBm 7707AR-8U
7707AR-8
7707AR-16 -28dBm 1310nm Wavelength
Single-Mode 24dB/80km** 7707ATxx-8U 7707ATxx-8
7707ATxx-16 0dBm 7707AR-8U
7707AR-8
7707AR-16 -28dBm CWDM Wavelengths
Single-Mode 31dB/105km** 7707ATxxxx-8U 7707ATxxxx-8
7707ATxxxx-16 +7dBm 7707AR-8U
7707AR-8
7707AR-16 -28dBm DWDM Wavelengths
Tx Power/Rx Sensitivity are nominal values ±1dBm
**Assume 8 Channel Mux/Demux loss of 3.5dB
Fiber Loss = 0.4/0.3dB per km @ 1310nm/1550nm
Table 1: Typical Application Configurations

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
7707AR-2 Revision 1.0
CONTROL/
INDICATION
VistaLINKTM
Interface
LOCAL
CONTROL LOCAL
INDICATION
8 or 16
AES Outputs
Optical
Receiver TDM Demux
Fiber
Input
Figure 1–1: 7707AR Block Diagram

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0 7707AR-3
2. Installation
The 7707AR series modules come with a companion rear plate that has AES audio connections and an
SC/PC (shown), ST/PC or FC/PC optical connector. The 7707AR-8 and 7707AR-16 versions provide AES
connections via multi-pin removable terminal blocks. The 7707AR-8U version provides AES connections
via BNCs. The 7707AR-8U-DB version provides unbalanced AES connections via a DB-25 connector,
which is backwards compatible with the 7705AR-8
For information on mounting the rear plate and inserting the module into the frame see the 7700FR
chapter section 3. The following diagram shows rear plate options for each 7707AR version.
Figure 2–1: 7707AR Rear Panels
2.1. OPTICAL CONNECTIONS
FIBER INPUT There is one SC/PC (shown), ST/PC or FC/PC female connector with the optical
input to the 7707AR. This wide band optical input accepts optical wavelengths of 1270nm to
1610nm, accommodating standard, CWDM or DWDM transmission schemes. This input is
compatible with multimode fiber when connected directly to a companion 7707AT card.

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
7707AR-4 Revision 1.0

Do not hook up the 7707AT DWDM cards and 7707AR cards directly with a short
fiber optic cable. The 7707AT DWDM card produces +7dBm of power which will
damage the receiver if connected directly.
2.2. AES CONNECTIONS
AES OUTPUTS The 7707AR-8U version provides BNC output connections compatible with unbalanced
AES audio. The 7707AR-8U-DB version has DB-25 connections for unbalanced audio that are
backwards compatible with 7705AR-8 as shown in Figure 2–2. The 7707AR-8 and 7707AR-16
versions provide terminal block output connections compatible with either balanced or
unbalanced AES. Balanced AES audio signals should be connected from the positive (+) and
negative (-) output terminals. Unbalanced AES audio signals should be connected from the
positive (+) output terminal, while the negative (-) output terminal remains disconnected.
Output impedance, amplitude, and rise/fall times are selectable to accommodate balanced or
unbalanced interfaces. Refer to section 4.2.3 for information on selecting balanced or
unbalanced output configurations.
For 7707AR-8U-DB versions the outputs should be set to the unbalanced
configuration.
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
25
13
GND UNUSED
UNUSED
UNUSED
UNUSED
GND
UNUSED
UNUSED
UNUSED
UNUSED
GND
GND
GND
AES OUT : 7
AES OUT : 8
AES OUT : 5
AES OUT: 6
GND
AES OUT : 3
AES OUT : 4
AES OUT : 1
AES OUT : 2
GND
GND
GND
Figure 2–2: 7707AR-8U-DB Pin Out

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0 7707AR-5
2.3. CARE AND HANDLING OF OPTICAL FIBER

Never touch the end face of an optical fiber. Always keep dust caps on optical fiber
connectors when not connected and always remember to properly clean the optical
end face of a connector before making a connection.
The transmission characteristics of the fiber are dependent on the shape of the optical core and therefore
care must be taken to prevent fiber damage due to heavy objects or abrupt fiber bending. Evertz
recommends that you maintain a minimum bending radius of 5 cm to avoid fiber-bending loss that will
decrease the maximum attainable distance of the fiber cable. The Evertz fiber optic modules come with
cable lockout devices, to prevent the user from damaging the fiber by installing a module into a slot in the
frame that does not have a suitable I/O module. For further information about care and handling of fiber
optic cable see section 3 of the Fiber Optics System Design chapter in the front of the binder.
3. SPECIFICATIONS
3.1. AES AUDIO OUTPUTS
Number of Outputs:
7707AR-8U: 8
7707AR-8U-DB:8
7707AR-8: 8
7707AR-16: 16
Connectors:
7707AR-8U: BNC per IEC 60169-8 Amendment 2
7707AR-8U-DB: DB-25
7707AR-8: Multi-pin Removable Terminal Blocks
7707AR-16: Multi-pin Removable Terminal Blocks
Standard:
7707AR-8U: SMPTE 276M - Unbalanced AES
7707AR-8U-DB: SMPTE 276M - Unbalanced AES
7707AR-8: AES3-1992, Balanced or Unbalanced (selectable)
7707AR-16: AES3-1992, Balanced or Unbalanced (selectable)
Output Sample Rate: 32 to 48KHz (same as input signal at 7707AT)
Input Return loss: >15dB
Output Impedance:
Unbalanced: 75Ω
Balanced: 110Ω
Output Amplitude:
Unbalanced: 1±0.1 Vp-p
Balanced: 2±0.1 Vp-p
Output Rise/Fall Times:
Unbalanced: 35ns ±5ns
Balanced: 20ns ±5ns
Output Jitter: < 0.1UI

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
7707AR-6 Revision 1.0
3.2. OPTICAL INPUT
Connector: SC/PC, ST/PC, FC/PC female housing
Input Wavelength: 1270 to 1610nm
Input Power (max): 0dBm
Input Optical Sensitivity: -28dBm
3.3. ELECTRICAL
Voltage: 12V DC
Power (max): 6 Watts
EMI/RFI: Complies with FCC regulations for class A devices.
Complies with EU EMC directive.
3.4. PHYSICAL
7700 frame mounting:
Number of Slots:
7707AR-8U: 2 slots
7707AR-8U-DB: 1 slot
7707AR-8: 1 slot
7707AR-16: 2 slots
7701 frame mounting:
Number of Slots: 1 slot all versions
4. CARD-EDGE MONITORING AND CONTROL
The 7707AR has eight or sixteen LED status indicators and a 4-digit dot-matrix display on the front card-
edge to show operational status of the card at a glance. The card-edge pushbutton and toggle switch are
used to select various indications to the dot-matrix display. Figure 4–1 shows the locations of the
indicators and pushbutton.

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0 7707AR-7
FRAME STATUS
ON/OFF
/ MODULE OK
LOCAL FAULT
CH:01
SERIAL
RUN/UPGRADE
SERIAL
CH:02
CH:03
CH:04
CH:05
CH:06
CH:07
CH:08
7707AR-16
Only
CH:09
CH:10
CH:11
CH:12
CH:13
CH:14
CH:15
CH:16
Figure 4–1: Location of Status Indicators and Jumpers

Older modules may have a control jumper and LED located beneath the audio jack
that was used to select either remote or local operation. For firmware versions
indicated in section 5.2, the card is controllable by local and remote control
simultaneously, meaning the jumper is not used. Changes made to the card via the
card edge or VistaLINK™ will be updated on both the card edge display and
VistaLINK™ monitored parameters.
4.1. STATUS INDICATOR LEDS
LOCAL FAULT: This red LED indicates poor module health. Two conditions could cause this fault
indication to be active: A link with a companion 7707AT has not been achieved, or if
a card power fault exists (i.e. a blown fuse). The LOCAL FAULT indication can also
be reported to the frame by setting the FRAME STATUS jumper.
MODULE OK: This green LED indicates good module health. It will be on while a link is maintained
with a companion 7707AT, and the card power is good.
CH:01 to CH:xx Each of these green LED’s indicate the signal presence of the respective AES
output channel. Signal presence indication considers X and Y preambles in
processed AES.
4.2. CARD-EDGE DISPLAY AND CONTROLS
Additional signal and status monitoring is provided via the 4-digit dot-matrix display located at the card-
edge. The card-edge pushbutton and toggle-switch are used to navigate through the display menu. Figure
5 provides a quick reference to the display menu structure.

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
7707AR-8 Revision 1.0
Pressing the pushbutton advances the display to the next menu level. The toggle-switch may then be used
to move up or down through selections of that menu level. Select BACK to return to previous menu level.
If a specific menu selection has a configuration value associated with it, then this may be changed using
the toggle switch. Pressing the pushbutton will apply the displayed value and return you to the previous
menu level.
The most recent user selection will be maintained in non-volatile memory in the event of power loss to the
module. Menu Level 1 Menu Level 2 Menu Level 3
PushbuttonPushbuttonPushbutton
Menu Selections: Configuration Values:
LINK…LOS (Link Loss)
Overrides
PWR (Optical Power)
-40 to +0 (dBm) Return to Level 1
Menu Selections: Configuration Values:
48K (48kHz) or
CH01 thru 44K (44kHz) or

CH08 or CH016 32K (32kHz) or
 LOS (Loss of Signal)
Toggle
RATE (Audio Rate)
BACK Return to Level 1
Switch Menu Selections: Configuration Values:
 CH01 thru BAL (Balanced)
CH08 or CH016 UBAL (Unbalanced)
TERM (Termination)
BACK Return to Level 1
Menu Selections: Configuration Values:
CH01 thru
CHAN (Channel) CH08 or CH016
VOL (Volume) 0 thru 64
Return to Level 2

JACK (Monitor Jack)
BACK Return to Level 1
Figure 4–2: Card-edge Menu Quick Reference
4.2.1. Displaying the Optical Power
The 7707AR can measure and display optical power over a range of –40 to 0dBm in 1dBm increments.
Please heed the maximum optical input power specification for the specific product option you possess.
Optical power monitoring is accommodated through the card-edge interface or VistaLINKTM. To display the
optical power to the card-edge select the PWR indication in menu level 1. The following list describes all
possible indications for this menu selection:
-40 to 0 Optical input power in dBm units
<–40 Optical input powers below –40dBm
>0 Optical input powers exceeding 0dBm
If there is no optical power present at the input, the card edge will display:
LINK…LOS Link fault condition exists. Overrides other indications

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0 7707AR-9
4.2.2. Displaying the AES Audio Sample Rate
The 7707AR can detect and indicate 32KHz, 44.1KHz, and 48KHz sample rates. Sample rate indication is
accommodated through the card-edge interface or VistaLINKTM. To display the sample rate to the card-
edge select the RATE indication in menu level 1. Use the toggle switch to choose the channel for which the
indication should be displayed. Press the pushbutton to apply the displayed selection.
CH01 to CH08 Range of AES Channels for the 7707AR-8, and 7707AR-8U product versions.
CH01 to CH16 Range of AES Channels for the 7707AR-16 product version.
The following list describes possible sample rate indications for the selected channel:
48K AES sample rate is 48KHz
44K AES sample rate is 44.1KHz
32K AES sample rate is 32KHz
LOS No valid AES signal is detected
Press the pushbutton to return to menu level 1.
4.2.3. Selecting the AES Output Signal Type
The 7707AR-8, and 7707AR-16 product versions accommodate balanced or unbalanced output signals.
Output amplitude, rise/fall time, and impedance characteristics are selectable to match either signal type.
Refer to section 2.1 for output connection details. Selection of the output signal type is done using the
card-edge interface or through VistaLINKTM control.
To select the output signal type, select the TERM menu item in menu level 1. The 7707AR allows the
output signal type to be set independently for each channel. Use the toggle switch to choose the channel
to which the selection will be applied. Press the pushbutton to apply the displayed selection.
CH01 to CH08 Range of AES Channels for the 7707AR-8 product version.
CH01 to CH16 Range of AES Channels for the 7707AR-16 product version.
The following list describes possible selections for output signal type:
BAL Output is configured for balanced AES signal type.
UBAL Output is configured for unbalanced AES signal type.
Switch to the desired output configuration using the toggle switch. Press the pushbutton to return to menu
level 2. You can select other items on menu level 2, or select the BACK menu item to return to menu level
1. The factory default configuration selects output signal type as BAL.
For 7707AR-8U-DB versions the outputs should be set to the unbalanced
configuration.

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
7707AR-10 Revision 1.0
4.2.4. Selecting the Headphone Jack Channel and Volume
The 7707AR provides a convenient audio monitoring headphone jack at the card-edge. This jack can be
used to verify signal presence or content for each AES channel. Headphone jack channel and volume are
selectable via the card-edge interface.
To configure the headphone jack, select the JACK menu item in menu level 1. The 7707AR allows user to
control the headphone monitoring jack channel and volume. Use the toggle switch to choose the
parameter to be controlled. Press the pushbutton to apply the displayed selection.
CHAN Allows selection of headphone monitoring channel.
VOL Allows selection of headphone monitoring volume.
The following list describes possible selections for headphone monitoring channel:
CH01 to CH08 Range of AES channels for the 7707AR-8, and 7707AR-8U product versions.
CH01 to CH16 Range of AES channels for the 7707AR-16 product version.
The following list describes possible selections for headphone monitoring volume:
0 to 64 Range of volume selection for the headphone monitoring jack.
Press the pushbutton to apply the displayed selection and return to menu level 2. You can select other
items on menu level 2, or select the BACK menu item to return to menu level 1.
5. JUMPER CONTROLS
Several jumpers, located at the front of the module are used to preset various operating modes. Figure 4–
1 shows the locations of the jumpers.
5.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS
The FRAME STATUS jumper determines whether local faults (as shown by the Local Fault indicator) will
be connected to the 7700FR frame's global status bus.
FRAME STATUS To monitor faults on this module with the frame status indicators (on the Power
Supply FRAME STATUS LED's and on the Frame's Fault Tally output) install this jumper in the
On position (default)
When this jumper is installed in the Off position local faults on this module will not be
monitored.

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
Revision 1.0 7707AR-11
5.2. FIRMWARE VERSIONS THAT ALLOW CARD TO BE CONTROLLED BY BOTH
LOCAL CONTROLS AND THE VistaLINKTM INTERFACE SIMULTANEOUSLY.
Board Option Support for control on both card edge and
VistaLINKTM interface available on the
following and later firmware versions.
AR-8 1v1_b57
AR-8U 1v1_b57
AR-16 1v1_b68
Table 2: Firmware for simultaneous local and remote control
Note: If the firmware does not support both control types, the CONTROL jumper allows
selection of either remote or local control. The corresponding CONTROL LED
will be lit when the card is under VistaLINKTM control.
5.3. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES
RUN/UPGRADE The RUN/UPGRADE jumper is used when firmware upgrades are being done to the
module. For normal operation it should be installed in the RUN position. See the Upgrading
Firmware chapter in the front of the binder for more information.
To upgrade the firmware in the module unit pull it out of the frame. Move the RUN/UPGRADE
jumper J16 into the UPGRADE position. Install the Upgrade cable provided (located in the
vinyl pouch in the front of the binder) onto SERIAL header J27 at the card edge. Re-install the
module into the frame. Run the upgrade as described in Upgrading Firmware chapter in the
front of the binder. Once the upgrade is completed, remove the module from the frame, move
J16 into the RUN position, remove the upgrade cable and re-install the module. The module is
now ready for normal operation.
6. VISTALINK™ REMOTE MONITORING/CONTROL
6.1. WHAT IS VISTALINK™?
VistaLINK™ is Evertz’s remote monitoring and control capability over an Ethernet network using Simple
Network Management Protocol (SNMP). SNMP is a standard computer network protocol that enables
different devices sharing the same network to communicate with each other. For monitoring, there needs
to be a detecting device that automatically reports all errors to a central alarm and error logging station.
We also need to be able to interrogate individual detector devices from the central station to determine the
status of individual channels. Finally, we need to be able to configure devices in the network from the
central station and receive feedback that the configuration has been carried out.
There are 3 components of SNMP:
1. An SNMP manager also known as a Network Management System (NMS) is a computer running
special software that communicates with the devices in the network. Evertz VL-Fiber demo Manager
graphical user interface (GUI), third party or custom manager software may be used to monitor and
control Evertz VistaLINK™ enabled fiber optic products.
2. Managed devices (such as 7707AR cards), each with a unique address (OID), communicate with the
NMS through an SNMP Agent. Evertz VistaLINK™ enabled 7700 series modules reside in the 3RU

7700 MultiFrame Manual
7707AR Multi-Channel AES Fiber Receiver
7707AR-12 Revision 1.0
7700FR-C MultiFrame and communicate with the manager via the 7700FC VistaLINK™ frame
controller module, which serves as the Agent.
3. A virtual database known as the Management information Base (MIB) lists all the variables being
monitored and which both the Manager and Agent understand. Please contact Evertz for further
information about obtaining a copy of the MIB for interfacing to a third party Manager/NMS.
For more information on connecting and configuring the VistaLINK™ network, see the 7700FC Frame
Controller chapter.
6.2. VISTALINK™ MONITORED PARAMETERS
The following parameters can be remotely monitored through the VistaLINK™ interface.
Parameter Description
Optical Power Optical input power from –40dBm to 0dBm
Link Loss Indicates a fiber link fault condition
Audio Signal Loss Indicates signal loss for each channel
Audio Rate Indicates sample rate for each channel
Optical Power Warning Indicates optical input power is below alarm
threshold level
Table 3: VistaLINK™ Monitored Parameters
6.3. VISTALINK™ CONTROLLED PARAMETERS
The following parameters can be remotely controlled through the VistaLINK™ interface.
Parameter Description
Output Signal Type Selects output as balanced/unbalanced
Optical Power Alarm
Threshold Selects the threshold level for the optical power warning
Table 4: VistaLINK™ Controlled Parameters
6.4. VISTALINK™ TRAPS
The following VistaLINK™ traps can be enabled and monitored.
Parameter Description
Optical Link Loss Indicates loss of optical power
Optical Power Warning Indicates optical input power is below threshold
alarm level
Table 5: VistaLINK™ Traps