EVGA Geforce GTX TITAN X Hybrid User manual

The following instructions and pictures are provided to assist you installation of the EVGA GTXTM Titan X
Hybrid Cooling Kit to the Reference Blower design of GTXTM Titan X graphics card. Please be careful
installing the hybrid, there are several very small fasteners used which can be stripped if you are
not careful.
Please be sure to keep your original shround and fasteners so it can be returned to how it
was received in case you ever need to submit for warranty.
12G-P4-2990-KR / 12G-P4-2992-KR instructions.
1) First remove the bracket by removing the 5 screws on the bracket,
the perpendicular screw holding the bracket to the PCB, and the 2
standoffs on the DVI port. (#1 Philips bit)
2) The shroud is held by 10 screws, remove them. (See pictures below.)
You will need a 2mm hex bit for the chrome bolts on the side and a
1.5mm hex bit for all others.
3) Remove the 4 spring screws on the back side of the card (#1 Philips Bit) this will allow the heatsink
to be removed.
4) Remove the 4 screws on cover, then remove the left cover (1.5mm hex bit).
E009-00-000128
1. 2.
7.
Installation Guide
14) Attach the shroud to the card, you can use the hoses and the fan as alignment marks. It will use the
8 bolt holes the original shroud used. Please use the included screws for the new shroud.
(#1 Philips bit) Please see step 2 for screw locations.
15) Realign the bracket with the back of
the card and replace the 6 screws and
2 standoffs removed in the first step.
Important Information
EVGA GTXTM TITAN X Hybrid Kit is AIO
Water Cooling System, you do not
need to add any coolant, and the
system is completely self-contained.
EVGA GTXTM TITAN X Hybrid Kit has
already done leaking test at the
factory before shipping to the
customers.
The EVGA GTXTM TITAN X Hybrid Kit is exclusive only to the NVIDIA®Reference PCB/Air cooling
GTXTM TITAN X graphics card and was not designed to fit on any other graphics card.
Warranty for the GTXTM TITAN X Hybrid Kit
Your EVGA TITAN X Hybrid kit comes with a 1 (one) year warranty. Refer to your GTXTM TITAN X
manufacturer’s warranty information before installing the EVGA GTXTM TITAN X Hybrid Kit. Should you
damage your GTXTM TITAN X during the installation process, EVGA will not be held liable for the physical
damage of your GTXTM TITAN X, Hybrid kit, case, motherboard or any associated hardware when damage
is caused by improper installation.
Color info : CMYK
Dimension: 17.7cm H X 13.5cm W (folded size)
GTX TITAN X Hybrid Waterblock

6.4.
5.3.
5) Now remove the heatsink and set it aside. We suggest cleaning the bottom of the heatsink, as the
thermal compound left there can smear and spread.
6) Remove the 4 screws holding the center portion of the shroud, and remove it. (#000 Philips bit)
12) Unplug the power for the existing fan plug in the waterblocks pass through power cable into the
cards power header, then reattach the fan to the card via the pass through. Make sure the wires
do not touch the fan; please use included strips of tape to attach the wires to the plastic around
the perimeter of the fan.
13) The secondary 3 pin cable from the waterblock powers the fan for the radiator. Attach it, and for
ease of cable routing, you can use the included ties to attach the cable to the hose.
7) Remove the remaining 2 screws (#000 Philips bit) and remove the last section of the shroud.
8) Unplug the LED header.
9) Be sure to clean the GPU (see pic) with alcohol
(preferably 90%) removing all thermal compound.
10) The included rubber cap (see front and back picture below) is attached to the framing of the card
and this is where the tubes will be held into place.
11) Remove the plastic cap on water block, use the 4 Spring Screws previously removed to mount the
block on the GPU (Thermal compound is pre-applied to the block).
Dimension: 17.7cm H X 13.5cm W (folded size)
Color info : CMYKGTX TITAN X Hybrid Waterblock