Evikon PluraSens E2418DF User manual

PluraSens®
Differential pressure transmitter
E2418DF
User Manual

E2418DF Rev 14.08.2023
Table of contents
Specifications 3
Product description 4
Safety requirements 4
Operating conditions 4
Installation and connections 5
Delivery set 8
Order code for E2418DF options 8
Configuring 8
Return to default settings 9
Emergency mode 10
Modbus RTU Communication 10
RS485 Communication parameters 12
Warranty 13
Manufacturer contacts 13
2

E2418DF Rev 14.08.2023
Specifications
Sensing method
Thermal microflow
Detection ranges
E2418-DF-50: -50...+50 Pa
E2418-DF-500: -500...+500 Pa
Resolution
0,1 Pa
Gas flow through sensor
23 ml/min for ±50 Pa range
100 ml/min for ±500 Pa range
Zero point accuracy
± 0,2 Pa, stability < 0,1 Pa / year
Span accuracy
±3% of reading
Temperature effect
< 0,5% of reading per 10°C
Atmospheric pressure effect
< 0,1 % of reading per hPa
Analog outputs
2 × 4-20 mA or 0-10 V, user settable
Digital interface
RS485, Modbus RTU protocol
Load resistance
RL < (Us - 3 V) / 22 mA for 4-20 mA
RL > 100 kOhm for 0-10 V mode:
Operating conditions
-20...+80 °C, 35…85%RH, without condensation
Aggressive gases or oil, residential or business spaces
Power supply
12…36 VDC (default)
24 VAC as option
Power consumption
< 2 VA
Electromagnetic compatibility
According to 2014/30/EU:
EN 61000-6-3:2020, EN 61326-1:2013(EMC, emissions)
EN 61000-6-1:2019, EN 61000-6-2:2019(EMC, Immunity)
Enclosure
Grey ABS 82×80×55 mm, IP65
3

E2418DF Rev 14.08.2023
Product description
Differential pressure transmitter-regulator E2418DF is a member of the new PluraSens®
family of multifunctional measurement instruments. The transmitter is intended for
measurement of pressure of air and non-aggressive gases with superb accuracy and no
offset drift.
The differential pressure is measured by a thermal sensor element using flow-through
technology. Compared with membrane based sensors, the method provides an extended
dynamic range, better long-term stability and improved repeatability, especially near zero.
E2418 features two independent analog outputs OUT1 and OUT2 user-selectable to 4-20
mA or 0-10 V. RS485 Modbus RTU digital communication interface allows easy instrument
configuration and integration into various automation systems.
Safety requirements
Always adhere to the safety provisions applicable in the country of use.
Do not perform any maintenance operation with the power on. Do not let water or foreign
objects inside the device.
Operating conditions
The device should be used in explosion-safe (non ATEX -rated) indoor areas, without
aggressive gases in the atmosphere.
4

E2418DF Rev 14.08.2023
Installation and connections
Unscrew four lid screws and detach the lid from the detector.
Fix the detector on a wall by screws, using cross-shaped mounting lugs supplied with the
instrument (see dimensional drawings below).
To connect the device with measurement point, use the hoses of appropriate diameter (4
or 6 mm) and length. Put one end of the hose on the fitting in the bottom part of the device
and fix the other end in the selected measurement area. The port marked with + (plus)
should be connected with the area of higher pressure (e.g. before air filter), the one marked
with - (minus) should be connected to the lower pressure area (e.g. behind air filter).
NB! The connecting hoses should not be squeezed or folded.
The connection diagram of the device is shown below.
NOTE! All dimensions are in millimeters.
5

E2418DF Rev 14.08.2023
Plug the power cable and connect the analog outputs and/or digital interface terminals to
the relevant devices according to the connection diagram and table.
PCB without PSU and relays
Jumpers
J1
OUT1 type (open: 4-20 mA; closed 0-10 V)
J2
OUT2 type (open: 4-20 mA; closed 0-10 V)
X6
Reset Modbus network parameters to default
X4 terminals
OUT1
4-20 mA / 0-10 V output
OUT2
4-20 mA / 0-10 V output
0V
0 V / 24 VAC Neutral (optional)
A
RS485 A / Data +
B
RS485 B / Data -
+U
+24 VDC / 24 VAC Phase (optional)
6

E2418DF Rev 14.08.2023
Make certain that the cable gland is properly tightened to ensure the conformity to IP65
protection class.
The screwless quick connect spring terminals on the E2418 are suitable for a wide range
of wires with cross-section 0,2...1,5 mm2. The recommended wire stripping length is 8...9
mm. Push the spring loaded terminal lever, insert the wire end into the terminal hole and
release the lever.
Use twisted pair cable, e.g. LiYY TP 2×2×0,5 mm2 or CAT 5, to connect the device to the
RS485 network. Use one pair for A and B wires and the second pair for common 0V and
power +U wires. to connect the transmitter to the Fieldbus network.polarity must be
respected when connecting to an external RS485 network.
Overall length of all connections via the RS485 interface should not exceed 1200 m.
Both analog outputs can be independently changed between 4-20 mA and 0-10 V type
using jumpers J1 (OUT1) and J2 (OUT2). By closing pins on a specific jumper the related
output is 0-10 V, with an open jumper the output is 4-20 mA. Power restart is required after
changing the position of the jumpers.
NOTE! The outputs are not galvanically isolated from the external power supply and share
a common 0V. Allowed load resistance limits are stated in the Specifications table. To
power the instrument from an external power source, connect terminals 0V and +U to the
source.
When the detector is fixed and the external devices connected, place the lid back and fix it
with the screws.
7

E2418DF Rev 14.08.2023
Delivery set
●Differential pressure transmitter-regulator E2418DF
●Mounting accessories:
○4 cross-shaped mounting lug with screws and 4 screws with plastic
dowels
Order code for E2418DF options
E2418DF options
Order code
Differential pressure transmitter-regulator, mass flow,
-50...50 Pa, resolution 0,025 Pa
E2418DF-50
Differential pressure transmitter-regulator, mass flow,
-500...500 Pa, resolution 0,25 Pa
E2418DF-500
Integrated 24 VAC power supply module
E2418-24VAC
Configuring
Differential pressure transmitter-regulator E2418DF shares all functionalities of the
PluraSens® multifunctional transmitter platform. The features and options include:
●Digital output change rate limiting filter
●Digital integrating (averaging) filter
●Temperature measurement channel with internal sensor
●Free assignment of each analog output to chosen parameter
●Flexible setting of analog output scales for each output
E2418 can be configured through its RS485 interface by Modbus RTU commands.
8

E2418DF Rev 14.08.2023
Return to default settings
To reset the device’s Slave ID, baud rate and stop bit number to factory settings, proceed as
follows:
1. De-energize the device
2. Connect the X6 jumper
X6 Jumper Closed (Connected)
X6 Jumper Open (Disconnected)
3. Turn on the device
4. De-energize the device
5. Disconnect the X6 jumper
6. Turn on the device
NOTE! Cables should be connected/disconnected from PCB when the power supply is
unplugged. Connecting or Disconnecting Live wires can result in Corrupt Firmware.
NOTE! Cables should only be connected / disconnected from the device when the power
supply is switched off. Connecting / disconnecting live wires to the device can cause
sparks which in result can affect device performance during operations. Electrical
installation should always be done by a qualified Technician.
9

E2418DF Rev 14.08.2023
Emergency mode
The current outputs of the detector may be programmed via Modbus commands (register
255) to signal if the connection with the sensor is lost. The signal may be set to 3,8 mA
(low current) or 21,5 mA (high current).
Bites
Functions
Notes
Default
bit[0]=0/1
sensor present/absent
Read-only
bit[1]=0/1
analog outputs activated/deactivated
1
bit[2]=0/1
in case of sensor absence, turn signalling
off/on (OUT 1)
1
bit[3]=0/1
In case of sensor absence turn on
signalling with low/high current on OUT 1
if bit [2]=0, this bit is ignored
0
bit[4]=0/1
in case of sensor absence, turn signalling
off/on (OUT 2)
1
bit[5]=0/1
In case of sensor absence turn on
signalling with low/high current on OUT 2
if bit [4]=0, this bit is ignored
0
bit[6]=0/1
Current/voltage output detected on OUT 1
Read-only
User defined
bit[7]=0/1
Current/voltage output detected on OUT 2
Read-only
User defined
bit[8]=0/1
LED deactivated/activated
Always 1 for 2418DF
1
Modbus RTU Communication
Modbus main holding registers (00xxx or 40xxx): 0-based, decimal
Reg
RW
Description
Supported values
1
R
hardware version
0...65535
2
R
software version
3
R
product serial number
0...65535
4
RW*
Slave ID [1...247]
0...247
5
RW*
baud rate
1200, 2400, 4800, 9600, 19200, 38400,
57600
6
RW**
Response delay, ms
1...255 ms
7
RW*
Stop bits
1 – No parity bit, 1 stop bit
(default after factory reset)
10

E2418DF Rev 14.08.2023
2 – No parity bit, 2 stop bits
3 – Odd parity, 1 stop bit
4 – Even parity, 1 stop bit
8
R
Last error code
1...255
17
RW***
Technological: data age in
seconds (read) / restart(write)
0...65535 s (read), 42330(write)
167
RW*
Change rate limit for
pressure data, pressure units
1...32000 pressure units,0=no limit
168
RW*
Integrating filter time constant
for pressure data, s
1...32000 s, 0=no filter
201
RW**
Parameter assigned to OUT1
0=none, 1=temperature,
2=pressure, 9=forced Modbus
control, value set in 203
202
RW**
Parameter assigned to OUT2
0=none, 1=temperature,
2=pressure, 9=forced Modbus
control, value set in 204
203
RW**
Forced value for OUT1
0...1000 (0.0%...100.0% of scale)
204
RW**
Forced value for OUT2
0...1000 (0.0%...100.0% of scale)
255
RW**
Sensor control/status
see Emergency mode paragraph
257
R
Raw pressure data
-32000...+32000 pressure units
258
R
Measured temperature, °Cx100
signed integer, -4000...+12500
(-40,00...+125,00 °C)
259
R
Measured pressure
-32000...+32000 pressure units
261
RW**
0% value of analog OUT1
-32000...+32000 pressure units
262
RW**
100% value of analog OUT1
-32000...+32000 pressure units
263
RW**
0% value of analog OUT2
-32000...+32000 pressure units
264
RW**
100% value of analog OUT2
-32000...+32000 pressure units
* - the new value is applied after restart.
** - the new value is applied immediately.
*** -writing 42330 restarts the device immediately, no response on Modbus
Broadcast ID=0 may be used to assign a new ID to device with unknown ID
For registers 203, 204, 213, 214 the value is dynamic and not kept in EEPROM
Pressure unit is 10 Pa
11

E2418DF Rev 14.08.2023
RS485 Communication parameters
Parameter
Permitted values
Default
Supported baud rates
1200, 2400, 4800, 9600, 19200, 38400, 57600
9600
Data bits
8
8
Parity
none / odd / even
none
Stop bits
1, 2
1
Protocol
Modbus RTU
Modbus functions
03 - Read multiple registers
06 - Write a single register
Error codes
01 – Illegal function
02 – Illegal data address
03 – Illegal data value
04 – Slave device failure
(details of last error 04 can be read from register 0x0008)
12

E2418DF Rev 14.08.2023
Warranty
This product is warranted to be free from defects in material and workmanship for a period
of one year from the date of the original sale. During this warranty period, the Manufacturer
will, at its option, either repair or replace a product that proves to be defective. This
warranty is void if the product has been operated in conditions outside ranges specified by
the Manufacturer or damaged by customer error or negligence or if there has been an
unauthorized modification.
Manufacturer contacts
Evikon MCI OÜ
Teaduspargi 9, Tartu
50411 Estonia
[email protected]
www.evikon.eu
13