Evo-lite LUXX 1010 NEON User manual

WWW.EVO-LITE.COM • [email protected] • 1-888-887-2980 • © EVO-LITE, LLC • 6240 W 54TH AVE., ARVADA, CO 80002 • V1–1822
HANDLING ADVISORY & PRE-INSTALL TESTING
Do not set anything on top of the product (i.e. tools, mugs,
etc.). Avoid placing product on oor or anywhere it could be
stepped on.
We advise that all products be inspected at time of delivery
and dry-t tested for proper illumination.
LUXX // LINEAR // NEON // 1010 NEON
1010 NEON
SHELF LIGHTING FIXTURE
Specic contents will vary based on your selected conguration.
PRODUCT CONTENTS
ELECTRICAL
Input Voltage 24VDC
Power Consumpon 2.9W per foot (9.6W per meter)
Wires 18AWG attached power lead
Cercaons cULus Listed (E501733), CE Compliant
// WARNING: RISK OF ELECTRIC SHOCK. Disconnect power at the source before installation, maintenance, or cleaning.
// This is a 24 Volt DC product. Connect to 24VDC only. NEVER connect to AC current or any other voltage. Best practices include allowing headroom for
power supply longevity.
// To reduce the risk of re, electric shock, or injury to persons, pay close attention to this manual and stay within its guidelines when using this
product. Save these instructions for future reference. Read and follow the product handling, installation, & integration advisory on page 4.
// Product should be installed in accordance with local/regional electrical codes and the current National Electric Code (NEC).
// Use only with UL Listed or UL Recognized Class 2, Limited Power Source (LPS) or Low Voltage Limited Energy (LVLE) power supplies. Provide the
appropriate number of 24V Class 2 circuits for your layout. Do not exceed the maximum load limit of any power supply per the manufacturer’s
recommendations.
// The use of the included power connector cable is required for warranty to be valid.
// Only used the supplied mounting hardware. Do not use other tapes or adhesives to secure xture in place.
// Use an MCB (mini circuit breaker) / fuse (slow blow) of at least 6A to prevent unwanted tripping caused by the inrush current of the LED driver.
// We advise using a zero-crossing/switching solid-state relay to reduce the inrush current peak.
// This product is designed for damp and dry locations only. Do not use this product in any location that may come into direct contact with moisture.
SAFETY & COMPLIANCE INFORMATION Read all instructions before beginning.
CLEANING THE PRODUCT
MOUNTING THE PRODUCT
SECURE MOUNTING CLIPS TO SURFACE SNAP PRODUCT INTO CLIPS
Use a clean, damp cloth and mild cleaning agent. Do not use abrasive cleaners, scouring pads, bleach, or cleaners containing chlorine as these may damage
the product
The following example depicts the standard mounting method. Your setup may vary based on the specic conguration of your product.
INSTRUCTION MANUAL
Specications subject to change without notice. Visit us online to view the most current information.
www.evo-lite.com
FIXTURE ATTACHED POWER LEAD MOUNTING HARDWARE

WWW.EVO-LITE.COM • [email protected] • 1-888-887-2980 • © EVO-LITE, LLC • 6240 W 54TH AVE., ARVADA, CO 80002 • V1–1822
INSTALLING THE PRODUCT
SINGLE CONNECTION SYSTEM SETUP
DAISY CHAIN SYSTEM SETUP
4-WAY SPLITTER SYSTEM SETUP
The following examples depict typical system setups / connections. Your setup may vary based on the specic conguration of your product.
4-Way Splitter
Power Input
Power Input
Power Input
24VDC Power Output
24VDC Power Output
24VDC Power Output
24VDC Class 2 Power Supply
24VDC Class 2 Power Supply
24VDC Class 2 Power Supply
Line
Voltage
Line
Voltage
Line
Voltage