manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Excentr
  6. •
  7. Cleaning Equipment
  8. •
  9. Excentr 40-25 Instruction manual

Excentr 40-25 Instruction manual

Excentr 40-25 Model 2019 -page 1 of 2 - File:Excentr40-25Krt-v1.0en.docx
EXCENTR
B.V.
Columbusweg 50
NL 4462HB GOES
Tel: +31 (0)88 1700 601
E-mail:
[email protected]m
1. Korte beschrijving:
1. Short description:
The Excentr 40-25 floor preparation machine is
designed to easily all kind of floors.
The Excentr 40-25 can also be used to strip or
grind/polish parquet floors with the use of special
pads (without use of chemicals!).
The plastic bumpers on all sides enable you to
accurately work close to edges.
What makes the machine unique is the so-called
Excentr method: the high velocity of 2500
movements per minute. This results in an
unmatched operation of the pad. The machine gives
you the feeling that it 'floats' across the floor, which
makes it easy and relaxed to handle the machine
during operation.
The 40-25 allows ballast plates to be placed on the
machine. This improves the effectiveness of the
Excentr method and thus working speed.
Power Supply: 220VAC, 50-60 Hz, 5A
WITH GROUNDING AND GFCI!
2. Safety:
WARNING!
Almost all accidents can be attributed to:
loss of concentration,
carelessness, negligence or
errors in judgment!
Work calmly and in a concentrated manner:
You have been warned!!
Snelstart handleiding
Short description
Safety
Use
Maintenance
Malfunctions
Also read the complete user manual!!
TAKE NOTE!
You are working with an electrical machine
and (scrub) water.
Make sure that the earthing and GFCI
function properly!!
Make sure that you do not use any damaged
cables!!
Preferably wear shoes with rubber soles!!
Wear ear protection!
Wear a dust mask when grinding!
Wear safety shoes with rubber
soles!
Take the plug out of the socket:
 first after the end-of-job
 When changing a pad
 When maintaining
 With repairs
Check the cable often for damage:
Repair a damaged cable first!!
It’s all for your safety!!
Quickstart manual
Excentr 40-25
Floor preparation machine
Excentr 40-25 Model 2019 -page 2 of 2 - File:Excentr40-25Krt-v1.0en.docx
EXCENTR
B.V.
Columbusweg 50
NL 4462HB GOES
Tel: +31 (0)88 1700 601
E-mail:
[email protected]m
3. Use:
Before starting treatment with the Excentr, examine
the floor on colour and shape retention
 Adjust the T-Handle position, if necessary.
 Before you start, check if the correct pad for the
job is attached.
 Check the ON/OFF switch is switched OFF.
 Insert the extension cable in the machine plug
and in a properly grounded wall socket.
 Power switch ON: the motor starts and the pad
starts working. Start moving the machine
immediately: else the floor can be damaged on
that spot.
 During work the machine can moved in all
directions easily and with little force. Work in long
tracks up and down, not in short back-and-forth-
going movements.
 Always turn the machine OFF immediately when
you quit working, else the floor can be damaged.
Take the plug out of the socket.
Ballast.
Experience in practice shows that, under certain
circumstances, the machine works better or faster if
there is extra
pressure on the pad:
Installation:
Place an equal
number of plates on
the left and right side
of the machine.
Fasten the plates with the star-knobs.
Removal: loosen the two knobs and remove the
plates. Always replace the star-knobs.
4. Maintenance:
Daily:
 Check the cables for damage
 Check the pad for wear.
 After using chemical cleaning agents, clean the
machine with a moist-damp cloth in order to
avoid that chemical agents corrode any stainless
steel parts.
 Check for loose bolts/nuts.
Monthly:
 Check the grip surface under the pad holder if it
still has sufficient grip for the pad.
 Check the vibration rubbers for tears!
Yearly:
 Make sure that the mandatory safety inspection
(NEN 3140) for electrical tools is done.
Pad replacement:
The pad is attached to the eccentric plate with
Velcro. Do the following steps:
 Turn off the machine.
 Remove the plug from the socket.
 Set the handle with T-handlebar to the highest
position.
 Tilt the machine backwards so that the handlebar
is on the floor and the pad is vertical.
 Pull the pad from
the eccentric plate.
 Attach the new
pad carefully to the
ec-centric plate and
then push it firmly
in place.
 Put the machine in upright position again.
 Put the plug in the socket.
 Turn the machine on and you are ready to work
again.
5. Malfunctions:
1) The machine does not start:
 Check the earth leakage circuit breaker.
 Check the power supply.
 Check the cables for damage.
 Contact your supplier.
2) The machine makes a rattling sound:
STOP IMMEDIATELY!! CHECK FIRST!!
 A nut has vibrated loose from the ballast
plates. RE-TIGHTEN!!
 A rubber from the pad holder is broken.
REPLACE!
 The eccentric bearing is worn. REPLACE!!
There is more than this quick start paper! For missing information read the Excentr 40-25 User Manual!!

Other manuals for 40-25

1

Other Excentr Cleaning Equipment manuals

Excentr 30-20+ User manual

Excentr

Excentr 30-20+ User manual

Excentr 55-35 User manual

Excentr

Excentr 55-35 User manual

Excentr DAILY 35E User manual

Excentr

Excentr DAILY 35E User manual

Excentr 40-25 User manual

Excentr

Excentr 40-25 User manual

Excentr 30-50 User manual

Excentr

Excentr 30-50 User manual

Popular Cleaning Equipment manuals by other brands

djm direct VMA915-O instructions

djm direct

djm direct VMA915-O instructions

Matrix Cleaning Systems 4x4SD10KW User instructions

Matrix Cleaning Systems

Matrix Cleaning Systems 4x4SD10KW User instructions

Kärcher PW 10 operating instructions

Kärcher

Kärcher PW 10 operating instructions

Rubbermaid WaveBrake Care and maintenance

Rubbermaid

Rubbermaid WaveBrake Care and maintenance

MS Schippers MS Greenline 0809889 Operation manual

MS Schippers

MS Schippers MS Greenline 0809889 Operation manual

Edic REVOLUTION owner's manual

Edic

Edic REVOLUTION owner's manual

Sealey SM28.V2 manual

Sealey

Sealey SM28.V2 manual

LAMETAL Stark THM 2500 Original operating and maintenance instructions

LAMETAL

LAMETAL Stark THM 2500 Original operating and maintenance instructions

GAT Stream manual

GAT

GAT Stream manual

Sapphire Audio HOSS 700 owner's manual

Sapphire Audio

Sapphire Audio HOSS 700 owner's manual

Bissell SPOTCLEAN TURBO AUTOMATE 1558X manual

Bissell

Bissell SPOTCLEAN TURBO AUTOMATE 1558X manual

Batavia TeamClean BT-WVC001 instructions

Batavia

Batavia TeamClean BT-WVC001 instructions

Alfalaval Toftejorg SaniJet 20 instruction manual

Alfalaval

Alfalaval Toftejorg SaniJet 20 instruction manual

Prochem BLAZER PLUS operating instructions

Prochem

Prochem BLAZER PLUS operating instructions

Alfalaval Toftejorg SaniJet 20 instruction manual

Alfalaval

Alfalaval Toftejorg SaniJet 20 instruction manual

Green Speed C-SHUTTLE 250DB manual

Green Speed

Green Speed C-SHUTTLE 250DB manual

Ebbe INNI Brush Cleaning Kit care and maintenance guide

Ebbe

Ebbe INNI Brush Cleaning Kit care and maintenance guide

Henkel Somat SMART Operation manual

Henkel

Henkel Somat SMART Operation manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.