Exerpeutic 1200 User manual

OWNER’S MANUAL
Folding Upright Bike with Pulse
IMPORTANT:
Read all instructions carefully before using this product. Retain this
owner’s manual for future reference. The specifications of this product
may vary from this photo, subject to change without notice.
4100.8-022117

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
STOP. Contact customer service if you have any questions
regarding assembly or proper operation of the machine.
Email us at:
[e-mail]
Or call us at:
1-844-641-7921
Hours:
8:00 am to 5:00 pm (PST) Daily

1
TABLE OF CONTENTS
SERVICE ------------------------------------------------------------------------ 2
LABEL PLACEMENT --------------------------------------------------------- 3
IMPORTANT SAFETY GUIDELINES ------------------------------------ 4
OVERVIEW DRAWING ------------------------------------------------------ 5
PARTS LIST -------------------------------------------------------------------- 6
HARDWARE & TOOL LIST ------------------------------------------------ 8
ASSEMBLY --------------------------------------------------------------------- 9
CONSOLE FUNCTIONS ---------------------------------------------------- 13
STORAGE ----------------------------------------------------------------------- 14
OPERATIONS & ADJUSTMENTS ---------------------------------------- 15
TRANSPORT ------------------------------------------------------------------ 17
MAINTENANCE & TROUBLESHOOTING ----------------------------- 18
WARRANTY -------------------------------------------------------------------- 20
PARTS REQUEST FORM -------------------------------------------------- 21

2
SERVICE
IMPORTANT: FOR NORTH AMERICA ONLY
For damaged or defective product, questions, replacement parts or any other service
support, please contact our customer service department by the below methods:
For The Best Service, please Email:
[e-mail]
Response Time: 1-2 Business Days
Emailing us with the information above will be the best method to receive a response during
peak business hours
Website:
www.paradigmhw.com
Toll-Free:
1-844-641-7921
(8:00 AM - 5:00 PM Pacific Standard Time, Daily)
Response time may vary via calling
Please have the following information ready when requesting for service:
•Your name
•Phone number
•Model number
•Serial number
•Part number
•Proof of Purchase
For damaged or defective product please contact our customer service before returning to
the store.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA

3
LABEL PLACEMENT

4
IMPORTANT SAFETY GUIDELINES
Basic precautions should always be followed, including the following safety guidelines
when using this equipment. Read all of the guidelines before using this equipment.
1. Before exercising and to avoid injuring your muscles, it is highly recommended that you perform
warm-up exercises for each muscle group.
2. Make sure all the components are not damaged and are in working order before using. This
equipment should be placed on a stable, flat surface. Using a mat or similar, covering material
on the ground is recommended.
3. Wear proper fitness apparel when using this equipment. Do not wear loose clothing or
accessories that may get caught by any part of the equipment.
4. Make sure all the components are not damaged and are in working order before using.
5. Remember to tighten the pedaling straps. Keep dry. Do not operate the equipment in wet or
moist condition.
6. Do not use the equipment outdoors. This equipment is for household use only.
7. Only perform maintenance or adjustments that are instructed in this manual. Should any
problems arise, discontinue usage of the equipment and consult with our customer service.
8. Only one person should be on the equipment at a time. Keep children and pets away from the
equipment at all times. This equipment is designed for adults only.
9. Be careful to always hold onto the handlebars when you’re mounting and dismounting. Be
careful to have the pedals at their lowest point when stepping off.
10.Hold onto the handlebars and use both the pedals in tandem to ensure a smooth, effective
workout.
11.This product requires a minimum of 6 square feet around for safe operation.
12.If you feel any chest pains, nausea, dizziness, or shortness of breath, you should stop
exercising immediately, and consult your physician before continuing.
13.This equipment is not intended for use by persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the equipment by a personal responsible for their safety.
14.DO NOT pedal in reverse.
15.The maximum weight capacity for this product is 400 lbs/181 kgs.
WARNING: Before beginning any exercise program consult your physician. This is
especially important for the people who are over 35 years old or who have pre-existing health
problems.
CAUTION:Read all instructions carefully before operating this product. Retain this
Owner’s Manual for future reference.
!
!

5
OVERVIEW DRAWING

6
PARTS LIST
No. Description Qty No. Description Qty
1 Front Frame 1 29 Hexagon Nut Cap M8 4
2 Rear Frame 1 30 Curve Washer Ø8.2xØ22.2 4
3 Rear Stabilizer 1 31 Front Stabilizer Ø50x1.5tx550L 1
4 Handlebar 1 32 C-ring Ø10 2
5 Seat Post 1 33 Flat Washer Ø8.2xØ16.8 9
6 Seat Cushion 1 34 Nylon Nut M8 1
7 Left Pedal 1 35 Magnet Bracket 1
8 Right Pedal 1 36 Washer Ø6.2 2
9 Computer 1 37 Sensor Wire 1
9A Hand Pulse Sensor 2 38 Flywheel 1
9B Computer Wire 1 39 Belt Wheel with Crank Axle 1
10 Wire Plug 1 40 Bearing Bracket A 2
11 Rear Stabilizer End Cap 2 41 Wave Washer 1
12 Seat Post Bushing 1 42 Bearing 4
13 Tension Control Knob 1 43 C-ring Ø17 6
14 Seat HeightAdjustment Knob 1 44 Belt Wheel 1
15 Tension Cable 1 45 Bearing 6000Z 2
15A Clip 1 46 Axle Ø12.8x94L 1
16 Oval Wire Plug 3 47 Eyebolt M6 2
17 Handlebar Foam Grip 2 48 Tension Bracket 2
18 Left Cover 1 49 Support Tube Holder 1
19 Right Cover 1 50 Nylon Nut M6 2
20 Top Cover 1 51 Nut M10 2
21 Plastic Bushing 6 52 Washer Ø10.2xØ25 1
22 Safety Pin 1 53 Wave Washer Ø17 1
23 Left Crank 1 54 Idle Wheel Axle 1
24 Right Crank 1 55 Nylon Nut M10 1
25 Flange Nut 2 56 Bearing 6902Z 2
26 Crank Cover 2 57 Axle Ø15.8x94.5L 1
27 Round Phillips Head Drilling
Screw M4x20 4 58 Hexagon Socket Bolt M8x15 9
28 Round Phillips Head Tapping
Screw M4x20 5 59 Rubber Cushion 1

7
PARTS LIST
No. Description Qty No. Description Qty
60 Washer Ø8.2x Ø25x2.0t 2 75 Screw M5x10 4
61 Flat Phillips Head Screw M6x10 6 76 Hexagon Socket Bolt M8x43L 1
62 Holder 1 77 Handlebar End Cap Ø25.4 3
63 Round Phillips Head Screw
M4x10 1 78 Front Frame Support Tube End Cap Ø22.2 2
64 Plastic Washer 1 79 Hand Pulse Sensor Wire 2
65 C-ring Ø15 1 80 Nut M6 1
66 Screw M4x10L 3 81 Screw M6x15 1
67 Rear Frame Support Tube 1 82 Hand Pulse Sensor 2
68 Screw M5x20 1 83 Countersunk Phillips Head Cap
Screw M4x20 2
69 Console cover 1 84 Left Nylon Nut 9/16 UNC12 1
70 Spring 1 85 Nut Bushing M10 1
71 Belt 240J4 1 86 Right Nylon Nut 9/16 UNC12 1
72 Belt 230J3 1 87 Left Pedal Strap 1
73R Front Stabilizer Right End Cap 1 88 Right Pedal Strap 1
73L Front Stabilizer Left End Cap 1 89 Crank Cover 2
74 Spring Washer Ø6.2 1

8
HARDWARE PACK & TOOLS LIST

9
ASSEMBLY
Step 1
1A Frame Set Up: Extend the Front Frame (1) and the Rear Frame (2). Rest the Rear Frame
Support Tube (67) into the hooked plate on the Front Frame (1). Align the upper pin holes of both
frames. Then insert the Safety Pin (22) into the Front Frame (1) and the Rear Frame (2) to lock
the frames in place (See Fig AA-1).
1B Front Stabilizer Installation: Attach the Front Stabilizer (31) onto the front curve of the Rear
Frame (2). Secure with two Hexagon Nut Caps (29) and two Curve Washers (30), and then
tighten using the 13-15mm Wrench provided.
1C Rear Stabilizer Installation: Attach the Rear Stabilizer (3) onto the rear curve of the Front
Frame (1). Secure with two Hexagon Nut Caps (29) and two Curve Washers (30), and then
tighten using the 13-15mm Wrench provided.
HARDWARE PACK
Front Stabilizer (31)
Transport Wheels
TOOL
13,15mm Wrench
1PC
(22) Safety Pin
1 PC (29) Hexagon Nut Cap 4PCS (30) Curve Washer 4 PCS

10
ASSEMBLY
Step 2
Tip: The Cranks, Pedals, Pedal Shafts, and the Pedal Straps are marked “R” for Right and “L” for
Left. Note: DO NOT turn the Left Pedal (7) in a CLOCKWISE direction. DO NOT turn the Right
Pedal (8) COUNTER-CLOCKWISE doing so will strip the threads of the left pedal shaft.
2A Installing the Left Pedal: Remove the Left Nylon Nut (84) from the Left Pedal (7). Insert the
Left Pedal (7) into the threaded hole in the Left Crank (23) in a COUNTER-CLOCKWISE direction
with your hand. Reinstall the Left Nylon Nut (84) onto the protruding shaft of the Left Pedal (7) in a
CLOCKWISE direction. Use the 13,15mm and 19mm Wrenches to simultaneously tighten the
Left Nylon Nut (84) and Left Pedal (7) in the same directions instructed. See Figure AA-2.
2B Installing the Right Pedal: Remove the Right Nylon Nut (86) from the Right Pedal (8). Insert
the Right Pedal (8) into the threaded hole in the Right Crank (24) via the CLOCKWISE direction
with your hand. Reinstall the Right Nylon Nut (86) onto the protruding shaft of the Right Pedal (8)
in a COUNTER-CLOCKWISE direction. Use the 13,15mm and 19mm Wrenches to
simultaneously tighten the Right Nylon Nut (86) and Right Pedal (8) in the same directions
instructed.
TOOLS
19mm Wrench
1PC
13-15mm Wrench
1PC
PRE-INSTALLED HARDWARE
(84) Left
Nylon Nut
1PC
(86) Right
Nylon Nut
1PC

11
ASSEMBLY
Step 3
Tip: The Seat Cushion (6)has 2 sets of adjustment holes. It is recommended that users between
5’1” – 5’6” use the holes towards the rear. It is recommended that users between 5’7” to 6’3” us the
holes towards the front.
3A Installing the Seat Cushion to the Seat Post: Align the bolt holes on the underside of the
Seat Cushion (6) with the holes on top of the Seat Post (5). Then attach the Seat Cushion (6) to
the Seat Post (5) with three Flat Washers (33) and three Hexagon Socket Bolts (58). Tighten the
Bolts (58) with the 5mm Allen Wrench with Philips Screwdriver provided.
3B Installing the Seat Post to the Rear Frame: Insert the Seat Post (5) into the Rear Frame (2)
and stop at your desired seat height. Install the Seat Adjustment Knob (14) into the threaded hole
on the right side of the Rear Frame (2) by turning it CLOCKWISE, making sure that the safety pin
of the Adjustment Knob (14) catches one of the height adjustment holes of the Seat Post (5).
HARDWARE:
5mm Allen Wrench with
Phillips Screwdriver
TOOL
(14) Seat Height
Adjustment Knob
1 PC
(33) Flat Washer
3PCS
(58) Hexagon
Socket Bolt
3PCS

12
ASSEMBLY
Step 4
Tip: If you need more room to install, lift the handlebars up.
4A Installing the Tension Control Knob: Place the Handlebar (4) onto the Front Frame (1), and
remove the Console Cover (69) from the back of the Handlebar (4). Turn the Tension Control
Knob (13) to the highest tension by turning it CLOCKWISE. Hook the tension cable from the
Tension Control Knob (13) into the cable lock of the Tension Cable (15) coming from the Front
Frame (1). See Figure AA-3. Remove the Clip (15A) after the two cables have been locked. See
AA-4. See Figure AA-5 for an example of how the cable lock should look like.
4B Connecting the Computer Wire to the Sensor Wire: Connect the Computer Wire (9B) to the
Sensor Wire (37). See Figure AA-5. Then re-attach the Console Cover (69) onto the back side of
the Handlebar (4). Secure the Handlebar (4) onto the Front Frame (1) with four Flat Washers (33)
and four Hexagon Socket Bolts (58). Tighten the Hexagon Socket Bolts (58) by using the 5mm
Allen Wrench with Phillips Screwdriver provided.
HARDWARE:
(58) Hexagon Socket Bolt
4PCS
(33) Flat Washer
4PCS
5mm Allen Wrench with
Phillips Screwdriver
1PC
TOOL

13
CONSOLE FUNCTIONS
COMPUTER FUNCTIONS:
TIME: Press the MODE key until the pointer locks onto TIME; this will display the amount of time
the bike has been in use.
SPEED: Press the MODE key until the pointer locks onto SPEED; this will display the current
speed being traveled.
DISTANCE: Press the MODE key until the pointer locks onto DISTANCE; this will display the
distance traveled during the current exercise session.
CALORIE: Press the MODE key until the pointer locks onto CALORIE; this will display the
estimated calorie burned.
ODOMETER:Automatically accumulates total distance traveled since first use of bike.
PULSE: Press the MODE key, until the pointer locks onto PULSE; this displays the users heart rate
while gripping the pulse sensors located on the handlebars.
SCAN: Changes the display periodically every 4 seconds
TIME---SPEED---DISTANCE---CALORIE---ODOMETER--- PULSE---SCAN
(Note: To leave the SCAN function, press the MODE key.)
HOW TO INSTALL THE BATTERIES:
(Note: When installing the batteries, don't press the mode button.)
1. Remove the battery cover at the rear of computer.
2. Place two "SIZE-AA" batteries into the battery housing.
3. Insure the batteries are correctly positioned and the battery springs are in proper contact with
the batteries.
4. Re-install the battery cover.
NOTE:
1. When inactive for 4-5 minutes the LCD display will automatically shut off.
2. To clear the workout data, hold the MODE key down for 3-10 seconds (This will not clear
ODOMETER)
3. When there is activity, the console will automatically turn on.
4. If the display is illegible or is partially illegible, remove batteries and wait 15 seconds before
reinstalling.
SPECIFICATIONS:
TIME---------------------------------------
0:00~99:59MIN
CALORIE---------------------------------
0.0~999.9KCAL
SPEED------------------------------------
0.0~999.9ML/H (KM/H)
ODOMETER-----------------------------
0~9999ML (KM)
DISTANCE-------------------------------
0.0~999.9ML (KM)
PULSE------------------------------------
40~240BPM

14
STORAGE
For your convenience, the bike can be folded up for storage.
1. Remove the Safety Pin (22) from the upper pin hole on the Front Frame (1)
2. Fold the Front and Rear frames together.
3. Re-insert the Safety Pin (22) into the lower pin hole on the Front Frame (1) to secure the
Front and Rear Frames (1,2) together.
4. Place the Rear Frame Support Tube (67) into the Support Tube Holder (49).

15
OPERATIONS & ADJUSTMENTS
Adjusting the Tension Control Knob
Increase Tension:
Turn the Tension Control Knob (13) clockwise.
Decrease Tension:
Turn the Tension Control Knob (13) counterclockwise.
Adjusting the Seat Height
Loosen the Seat Height Adjustment Knob (14) by turning it counterclockwise. Pull AND hold to
release the pin. While the Knob is being pulled, adjust the Seat Post (5) to the desired height.
Release the Seat Height Adjustment Knob (14) to allow the pin to catch one of the holes along
the Seat Post (5). Then tighten Seat Height Adjustment Knob (14) by turning it clockwise to
secure the seat in place.
NOTE: When adjusting the height of the Seat Post (5), make sure the height of the Seat Post (5)
does not exceed the MAX line on the Seat Post (5).
Tension Control Knob (13)
Seat Height Adjustment Knob (14)

16
OPERATIONS & ADJUSTMENTS
Adjusting the Pedal Strap
The Left Pedal Strap (87) has an L marked on the strap (see Figure 1).
Snap the slotted end of the Left Pedal Strap (87) onto the tab on the inside edge of the Left Pedal
(7) (see Figures 2 and 3).
Insert the ridged end of the Left Pedal Strap (87) into the red clip on the Left Pedal (7) (see
Figures 4).
Adjusting the Left Pedal Strap: To make the Left Pedal Strap (87) more tight, pull the lower
ridged portion down (see Figures 5). To make the Left Pedal Strap (87) more loose, push the red
clip down and pull up on the upper portion of the Left pedal strap (87) (see Figures 5).
Adjusting The Right Pedal Strap: Use the same procedure to assemble and adjust the Right
Pedal Strap (88) onto the Right Pedal (8).
1
L mark
2
3
4 5
Upper
Lower
4
5

17
TRANSPORT
Transporting the Bike
Hold the Handlebar (4) and tilt the bike forward until the wheels on the Front Stabilizer (31) make
contact with the floor. Push or pull the unit to the desired location, then gently lower the Rear
Stabilizer (3) back down to the ground.

18
MAINTENANCE & TROUBLESHOOTING
MAINTENANCE
Cleaning
The bike can be cleaned with a soft, clean damp cloth. Do not use abrasives or solvents on the
plastic parts. Wipe your perspiration off the bike after each use. Be careful not to get excessive
moisture on the computer display panel as this might cause an electrical hazard or the electronics
to fail. Keep the computer console and the bike, out of direct sunlight to prevent screen damage.
Inspect all assembly bolts, nuts, screws, and pedals on the machine for proper tightness every
week.
Storage
Store the bike in a clean and dry environment away from pets and children.
TROUBLE SHOOTING
PROBLEM: There is no display on the computer console.
SOLUTION: Remove the Console Cover (69) and verify that the wire that comes from the
computer console is properly connected to the wires that come from the rear frame.
SOLUTION: Check if the batteries are correctly positioned and the battery springs are in proper
contact with the batteries.
SOLUTION: The batteries in the computer console may be dead. Replace the dead batteries with
new batteries.
PROBLEM: There is no heart rate reading or the heart rate reading is erratic / inconsistent.
SOLUTION: Make sure that the wire connections for the hand pulse sensors are secure.
SOLUTION: To ensure the pulse readout is accurate, always hold on to the handlebar grip sensors
with two hands instead of just with one hand.
SOLUTION: Avoid gripping the hand pulse sensors too tight. Try to maintain even pressure while
holding onto the hand pulse sensors.
PROBLEM: The bike makes a squeaking noise when in use.
SOLUTION: The bolts may be loose on the equipment. I all of the nuts, bolts, screws and tighten
any loose Hardware.