Exerpeutic 1200 User manual

Folding Upright Bike with Pulse
IMPORTANT:
Read all instructions carefully before using this product. Retain this owner’s manual for
future reference.
The specifications of this product may vary from this photo, subject to change without notice.
OWNER’S MANUAL
1200.10-041317

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
STOP. Contact customer service if you have any questions
regarding assembly or proper operation of the machine.
Email us at:
[e-mail]
Or call us at:
1-844-641-7921
Hours:
8:00 am to 5:00 pm (PST) Daily

1
SERVICE --------------------------------------------------------------------------2
LABEL PLACEMENT ---------------------------------------------------------- 3
IMPORTANT SAFETY GUIDELINES -------------------------------------- 4
OVERVIEW DRAWING -------------------------------------------------------- 6
PARTS LIST ----------------------------------------------------------------------- 7
HARDWARE & TOOLS PACK ------------------------------------------------ 9
ASSEMBLY ------------------------------------------------------------------------ 10
CONSOLE --------------------------------------------------------------------------14
STORAGE --------------------------------------------------------------------------15
OPERATIONS & ADJUSTMENTS ------------------------------------------- 16
TRANSPORTATION ------------------------------------------------------------- 19
MAINTENANCE & TROUBLESHOOTING -------------------------------- 20
WARRANTY ----------------------------------------------------------------------- 21
PARTS REQUEST FORM ----------------------------------------------------- 22
TABLE OF CONTENT

2
IMPORTANT: FOR NORTH AMERICA ONLY
For damaged or defective product, questions, replacement parts or any other service
support, please contact our customer service department (8:00 AM - 5:00 PM Pacific
Standard Time, Daily) by the below methods:
For The Best Service, please Email:
[e-mail]
Response Time: 1-2 Business Days
Emailing us with the information above will be the best method to receive a response during
peak business hours
Website:
www.paradigmhw.com
Toll-Free:
1-844-641-7921
Response time may vary via calling
Refer to our email for the best response time
Please have the following information ready when requesting for service:
Your name
Phone number
Model number
Serial number
Part number
Proof of Purchase
For damaged or defective product please contact our customer service before returning to
the store.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA
SERVICE

3
LABEL PLACEMENT

4
Read all instructions before using the Bike. When using our equipments, basic precautions should
always be followed, including the following:
WARNING - To reduce the risk of injury to persons:
1. Make sure your equipment is correctly assembled before you use it.
2. Be sure all screws, nuts, and bolts are tightened prior to use.
3. Only one person should use the equipment at a time.
4. Never operate this equipment if it is damaged, If it is not working properly, has been dropped, or
damaged. If a problem is encountered contact Customer Service before using the equipment again.
5. Always use this equipment on a clear and level surface.
6. For household use only.
7. Do not use outdoors or near water.
8. Use the equipment only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacturer.
9. Do not wear loose clothing when using the equipment.
10.Keep all hands and feet away from any moving parts.
11.Never drop or insert any object into any opening.
12.Always wear shoes when using the equipment.
13.This equipment is not intended for use by persons with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use
of the equipment by a personal responsible for their safety.
14.If at any time you feel faint, light-headed, or dizziness while operating the equipment, stop exercising
immediately. You should also stop exercising if you are experiencing pain or any discomfort.
15.DO NOT pedal in reverse.
16.Assemble All Parts & Hardware Accordingly To The Assembly Steps. Use The
Illustrations For Reference.
17.Warning: - Risk of Personal Injury –Do not allow children to use this machine.
18.Warning: - Risk of Personal Injury –Keep body parts, hair, loose clothing, and jewelry clear of all
moving parts.
19.Warning: - Risk of Personal Injury - Do not attempt to service the unit yourself. Discontinue use and
contact customer service.
The maximum weight capacity for this product is 300 lbs/136 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the people who are over 35 years of age or who have
pre-existing health problems. Read all instructions before using any fitness equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.
IMPORTANT SAFETY GUIDELINES
!
!

5
The product weighs more than 44 lbs. It is heavily
recommended that at least 2 persons assemble.
Do not use this equipment if you have any of the following conditions or ailments:
Pregnancy
Extreme obesity
Middle ear infection
Hiatus hernia or Ventral hernia
Glaucoma, retinal detachment or conjunctivitis
Use of anticoagulants including Aspirin in high doses.
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Heart or circulatory disorders for which you are being treated
High blood pressure, Hypertension, Recent stroke or Transient Ischemic attack
Bone weaknesses including Osteoporosis, Unhealed fractures, Modular pins, or surgically implanted
orthopedic supports.
Do not exceed the maximum rated weight (load) and maximum rated
user height:
The Maximum Weight Capacity for this product is 300lbs/136kgs.
Retain this owner’s manual and keep the original purchase receipt
for future reference.
SAVE THESE GUIDELINES
IMPORTANT SAFETY GUIDELINES

6
OVERVIEW DRAWING

7
No.
Description
Qty
No.
Description
Qty
1
Rear Frame
1
30
Curve Washer Ø8.2xØ22.2
4
2
Front Frame
1
31
Front Stabilizer Ø50x1.5tx550L
1
3
Rear Stabilizer Ø50x1.5tx550L
1
32
C-ring Ø10
2
4
Handlebar Ø25
1
33
Flat Washer Ø8.2xØ16.8
5
5
Seat Post
1
34
Nylon Nut M8
1
6
Seat Cushion
1
35
Magnet Bracket
1
7
Left Pedal (YH-30X)
1
36
Washer Ø6.2
2
8
Right Pedal (YH-30X)
1
37
Sensor with Wire
1
9
Console (81414)
1
38
Flywheel
1
10
Wire Plug (15x9)
1
39
Belt Wheel with Crank Axle
1
11
Rear Stabilizer End Cap
2
40
Bearing Bracket A
2
12
Seat Post Plastic Bushing
1
42
Bearing 6003RS
4
13
Tension Control Knob (1080L)
1
43
C-ring Ø17
6
14
Seat Height Adjustment Knob
M16
1
44
Belt Wheel
1
15
Sensor Wire (900L)
1
45
Bearing 6000Z
2
16
Oval Wire Plug
4
46
Axle Ø12.8x94L
1
17
Handlebar Foam Grip
Ø23x5.0tx420L
2
47
Eyebolt M6
2
18
Left Shroud
1
48
Tension Bracket
2
19
Right Shroud
1
49
Support Tube Clip
1
20
Top Shroud
1
50
Nylon Nut M6
2
21
Round Plastic Bushing
6
51
Nut M10
3
22
Safety Pin Ø10x110L
1
52
Washer Ø10.2xØ25
1
23
Left Crank
1
53
Wave Washer Ø17
1
24
Right Crank
1
54
Idle Wheel Axle
1
25
Flange Nut
2
55
Nylon Nut M10
1
26
Crank Cover
2
56
Bearing 6902Z
2
27
Round Phillips Head Drilling
Screw M4x20
7
57
Axle Ø15.8x94.5L
1
28
Round Phillips Head Tapping
Screw M4x20
4
29
Hexagon Nut Cap M8
4
PARTS LIST

8
No.
Description
Qty
No.
Description
Qty
58
Hexagon Socket Bolt M8x15
5
75
Screw M5x15
2
59
Rubber Cushion
1
76
Hexagon Socket Bolt M8x40L
1
60
Washer Ø8.2x Ø25x2.0t
2
77
Handlebar End Cap Ø25.4
2
61
Flat Phillips Head Screw M6x10
6
78
Front Frame Support Tube End
Cap Ø22.2
3
62
Bottle Holder
1
79
Hand Pulse Sensor Wire
2
63
Round Phillips Head Screw
M4x10
1
80
Nut M6
1
64
Plastic Washer
2
81
Screw M6x15
1
65
C-ring Ø15
1
82
Hand Pulse Sensor
2
66
Screw M4x10L
2
83
Countersunk Phillips Head Cap
Screw M4x20
2
67
Support Tube
1
84R
Front Stabilizer Right End Cap
1
68
Screw M5x20
1
84L
Front Stabilizer Left End Cap
1
69
Washer Ø5.2xØ18
1
85
Spring Washer M6
1
70
Spring
1
86
Left Pedal Nut 9/16 UNC12
1
71
Belt 240J4
1
87
Right Pedal Nut 9/16 UNC12
1
72
Belt 230J3
1
88
Left Pedal Strap
1
73
Hexagon Socket Bolt M6x12
4
89
Right Pedal Strap
1
74
Spring Washer Ø6.2
4
90
Bearing Bracket B
2
PARTS LIST

9
HARDWARE & TOOLS PACK

10
STEP 1
1A Setting Up The Frames Of The Bike: Stand up the base of the Rear and Front Frames (1, 2)
by pulling them apart from each other. Rest the Support Tube (67) into the hooked plate on the
Rear Frame (1). Align the upper pin holes on where both Frames (1, 2) intersect and insert the
Safety Pin (22) to lock the frames in place.
1B Installing The Front Stabilizer: Ensuring that the UP Sticker is visible on the outside and
facing correctly, attach the Front Stabilizer (31)with the Transport Wheels onto the Front Frame
(2) with two Hexagon Nut Caps (29) and two Curve Washers (30). Tighten the Hexagon Nut
Caps (29) with the 13 - 15mm Wrench provided.
1C Installing The Rear Stabilizer: Ensuring that the UP Sticker is visible on the outside and
facing correctly, attach the Rear Stabilizer (3) onto the Rear Frame (1) with two Hexagon Nuts
Cap (29) and two Curve Washers (30). Tighten the Hexagon Nut Caps (29) with the 13 –15mm
Wrench provided.
ASSEMBLY
TOOL
13-15mm Wrench
HARDWARE PACK
(22) Safety Pin
1 PC
(29) Hexagon Nut Cap M8
4PCS
(30) Curve Washer
4 PCS
HARDWARE PACK
(29) Hexagon Nut Cap
4PCS
(30) Curve Washer
4PCS
(22) Safety Pin
1PC
HARDWARE PACK

11
STEP 2
Tip: Only turn the pedals in the direction instructed. The left, right pedals and left, right
pedal nuts will have different directions for installation. The Cranks, Pedals, Pedal Shafts,
Pedal Nuts, and Pedal Straps are marked “R” for Right and “L” for Left.
2A Removal Of Hardware: Remove the Left Pedal Nut (86) and Right Pedal Nut (87)from the
Left and Right Pedal (7, 8).
2B Installing The Pedal Straps To The Pedals: Install the Left Pedal Strap (88) onto the Left
Pedal (7). Install the Right Pedal Strap (89) onto the Right Pedal (8). See Operations &
Adjustment Page 17.
2B Installing The Left Pedal Onto The Left Crank: Insert the Left Pedal (7) perfectly straight into
the threaded hole in the Left Crank (23). Turn the pedal shaft by hand in a
COUNTER-CLOCKWISE direction until snug. Use the the 13 –15mm Wrench to tighten the Left
Pedal (7) until the shaft protrudes. Attach the removed Left Pedal Nut (86) to the protruding shaft
in a CLOCKWISE direction. Use both the 13-15mm Wrench and 19mm Wrench to simultaneously
tighten the Left Pedal (7) and the Left Pedal Nut (86). Only tighten in the directions instructed.
2C Installing The Right Pedal Onto The Right Crank: Insert the Right Pedal (8) perfectly
straight into the threaded hole in the Right Crank (24). Turn the pedal shaft by hand in a
CLOCKWISE direction until snug. Use the the 13 –15mm Wrench to tighten the Right Pedal (8)
until the shaft protrudes. Attach the removed Right Pedal Nut (87) to the protruding shaft in a
COUNTER-CLOCKWISE direction. Use both the 13-15mm Wrench and 19mm Wrench to
simultaneously tighten the Right Pedal (8) and the Right Pedal Nut (87). Only tighten in the
directions instructed.
ASSEMBLY
TOOLS
13-15mm Wrench
19mm Wrench
PREINSTALLED HARDWARE
(86) Left Pedal Nut
1 PC
(87) Right Pedal Nut
1 PC

12
STEP 3
Tip: The Seat Cushion (6) has 2 sets of adjustment holes. It is recommended that users between
5’1” – 5’6” use the holes towards the rear of the seat and users between 5’7” to 6’3” use the holes
towards the front. See Operations & Adjustment Page 18.
3A Installing The Seat Cusion To The Seat Post: Align the bolt holes on the underside of the
Seat Cushion (6) with the holes on top of the Seat Post (5). Attach the Seat Cushion (6) to the
Seat Post (5) with three Flat Washers (33) and three Hexagon Socket Bolts (58). Tighten the
Bolts (58) with the 5mm Allen Wrench with Phillips Screwdriver provided.
3B Installing The Seat Post To The Front Frame: After securing the Seat Cushion (6) to the
Seat Post (5), insert the Seat Post (5) through the Seat Post Plastic Bushing (12) and into the
tube of the Front Frame (2). Insert the Seat Height Adjustment Knob (14) into the threaded hole
on the right side of the Front Frame (2). Turn the Seat Height Adjustment Knob (14) in a
CLOCKWISE direction making sure that the Seat Height Adjustment Knob (14) catches one of
the height adjustment holes on the Seat Post (5) before you start fully tightening the Knob (14).
(14) Seat Height
Adjustment Knob
1 PC
(33) Flat Washer
3 PCS
(58) Hexagon Socket Bolt
3 PCS
ASSEMBLY
5mm Allen Wrench with Phillips
Screwdriver
TOOL
HARDWARE PACK

13
STEP 4
4A Connecting The Sensor Wires: Connect the female Sensor Wire (15) from the Rear Frame
(1) to the male wire from the Console (9).
4B Installing The Handlebars: Attach the Handlebar (4) onto the top of the Rear Frame (1) with
four Hexagon Socket Bolts (73) and four Spring Washers (74). Tighten the Bolts (73) with the
5mm Allen Wrench with Phillips Screwdriver provided.
4C Installing The Bottle Holder: Attach the Bottle Holder (62) onto the Rear Frame (1) with two
Screws (66). Tighten the Screws (66) with the 5mm Allen Wrench with Phillips Screwdriver
provided.
ASSEMBLY
5mm Allen Wrench with Phillips
Screwdriver
TOOL
(66) Screw
2PCS
2 PCS
(73) Hexagon Socket
Bolt
4 PCS
(74) Spring Washer 4PCS
4 PCS
HARDWARE PACK

14
SPECIFICATIONS:
TIME --------------------------------------- 0:00-99:59 MIN: SEC
SPEED ------------------------------------ 0.0-999.9 ML/H
DISTANCE ------------------------------- 0.0-999.9 ML
CALORIE --------------------------------- 0.0-999.9 KCAL
ODOMETER ----------------------------- 0.0-999.9 ML
PULSE ------------------------------------ 40-240 BEATS/MIN
CONSOLE FUNTIONS:
AUTO ON/OFF: The console will automatically turn on
when exercise is detected. If you leave the console idle for
4 minutes, the power will shut off automatically.
SCAN: Press the button until the screen displays SCAN;
the console will automatically scan the functions of TIME,
ODOMETER, CALORIE, PULSE, SPEED, and DISTANCE,
every 6 seconds.
TIME: Displays your elapsed workout time in minutes and seconds. The console will automatically
count up from 0:00 to 99:59 in one second intervals.
SPEED: Displays your workout speed in miles per hour.
DISTANCE: Displays the total distance traveled during each workout up to a maximum of 999.9
miles.
CALORIE: The console will estimate the cumulative calories burned at any given time during your
workout. The console will count up from 0.0 to 999.9 calories.
ODOMETER: Displays the total accumulative distance traveled during each workout up to a
maximum of 999.9 miles. The data values of the ODOMETER will not be reset to zero when
pressing and holding the button more than 2 seconds. If user takes out the batteries out from the
console, the ODOMETER data values will reset to zero.
PULSE: The console will display your pulse rate in beats per minute after holding both hands on
the handlebar grip sensors during exercise. To ensure the pulse readout is more precise, always
hold on to the handlebar grip sensors with two hands instead of one.
RESET: pressing and holding the button more than 2 seconds will reset all functional values to zero
except for the odometer data values.
HOW TO INSTALL THE BATTERIES:
1. Remove the battery cover at the rear of the console.
2. Place two "SIZE-AAA" batteries into the battery housing.
3. Ensure the batteries are correctly positioned and the battery springs are in proper contact with
the batteries.
4. Re-install the battery cover.
5. If the display is illegible or only partial legible, remove the batteries and wait 15 seconds before
reinstalling.
CONSOLE

15
For your convenience, the bike can be folded up for storage.
1. Remove the Safety Pin (22) from the upper pin hole of the bike.
2. Fold the Rear Frame (1) and the Front Frame (2) together until the lower pin holes are
aligned.
3. Re-insert the Safety Pin (22) into the lower pin hole to secure the frames.
4. Lock the Support Tube (67) into the Support Tube Holder Clip (49).
STORAGE
49
49

16
Adjusting the Tension Control Knob
To increase the tension, turn the Tension Control Knob (13) in a CLOCKWISE direction. ↻
To decrease the tension, turn the Tension Control Knob (13) in a COUNTERCLOCKWISE
direction. ↺
Adjusting the Seat Height
Turn the Seat Height Adjustment Knob (14) in a COUNTERCLOCKWISE direction until the Seat
Post (5) can be slid up or down. Then slide the Seat Post (5) up or down to a suitable position.
Lock the Seat Post (5) in place by tightening the Seat Height Adjustment Knob (14) in a
clockwise direction.
NOTE: When adjusting the height of the seat post, make sure the MAX line stamped on the
right side of the seat post does not pass the plastic bushing.
OPERATIONS & ADJUSTMENTS

17
Adjusting the Pedal Strap
The Left Pedal Strap (88) is marked with an L on the strap. See Figure 1 .
Snap the three hole end onto the inside edge of the Left Pedal Strap (88) See Figure 2 & 3.
Select one of the adjustment holes which allow your foot to be easily removed
from the pedal. Snap the other end onto the outside edge of the Left Pedal Strap (88) with the L
mark on the strap. See Figures 4 and 5.
Use the same procedure to snap the Right Pedal Strap (89) onto the right pedal.
3
2
4
5
1
L mark
OPERATIONS & ADJUSTMENTS

18
Seat Cushion Adjustment
The Seat Cushion (6) can be adjusted for users of different heights.
Adjust the Seat Cushion (6) to the Bposition for people whose height is between 5’1” to 5’6”.
Assemble the Seat Cushion (6) and align the bolt holes on the underside of Seat Cushion (6) with
the holes on top of the Seat Post (5). Then attach it with three Flat Washers (33) and three
Hexagon Socket Bolts (58). Tighten the bolts with the 5mm Allen Wrench with Phillips
Screwdriver provided.
Adjust the Seat Cushion (6) to the A position for people whose height is between 5’7” to 6’3”.
Assemble the Seat Cushion (6) and align the bolt holes on the underside of the Seat Cushion (6)
with the holes on top of the Seat Post (5), Then attach it with three Flat Washers (33) and three
Hexagon Socket Bolts (58). Tighten bolts with the 5mm Allen Wrench with Phillips
Screwdriver provided.
OPERATIONS & ADJUSTMENTS
5mm Allen Wrench with Phillips
Screwdriver
TOOL