ExpertDAQ EX-9512S User manual

1
EX-9512S
One Port PoE Splitter
User’s Manual

2
FCC Warning
This device has been tested and found to comply with limits for a Class A digital device, pursuant to Part 2 and
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses
and radiates radio frequency energy and, if not installed and used in accordance with the user’s manual, may
cause interference in which case user will be required to correct the interference at his own expense.
NOTICE:
1. The changes or modifications not expressively approved by the party responsible for compliance could
void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the
emission limits.
CISPR A COMPLIANCE:
This device complies with EMC directive of the European Community and meets or exceeds the following
technical standard.
EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology
Equipment. This device complies with CISPR Class A.
WARNING:
This is a Class A product. In a domestic environment, this product may cause radio interference in which
case the user many be required to take adequate measures.

3
Table of contents
Chapter 1 …………………………………………………………………………………….. 4
Introduction ..………………………………………………………………………………4
Product Features…………………………………………………………….…………….4
Technical Specifications …………………………………………………….…………..4
Chapter 2 ………………………………………………………………………………………5
Package contents …………………………………………………………………………5
Chapter 3 ……………………………………………………………………………………….5
Installation …………………………………………………………………………………..5
The LED indicators …………………………………………………………………………5
Chapter 4 ……………………………………………………………………………………….6
Application ………………………………………………………………………………….6

4
Chapter 1.
Introduction
The splitter is a Power Over Ethernet splitter, it split the data and power from the cable come over PSE.
When the input port connects to PSE via Cat5 cable, the splitter will pass-through the data signal to its
RJ-45 output port, and also converter the 48V PoE power to DC5V/12V to the output power jack. With this
splitter, a client device without PD feature also can enjoy the power from PSE device.
Product Features
Complies with IEEE802.3u 10Base-T/100Base-TX, IEEE-802.3af PoE Standards.
TP port support Auto-MDIX & Auto-negotiation.
TP port up to 100 meters for shielded/unshielded twisted pair cable.
Supports Full-duplex & Half-duplex operation on TP base onAuto-negotiation.
Supply power source of 5V or 12V (selectable) up to 19.2W peak.
Small dimension, can easily install anywhere.
Technical Specifications
◎Standards : IEEE 802.3u 10Base-T/100Base-TX and IEEE 802.3af
◎Media support : 10BASE-T EIA/TIA 568 Cat3, 4, 5, 5e or 6 UTP/STP
: 100Base-TX EIA/TIA 568 Cat5, 5e or 6 UTP/STP
◎Distances support : Twisted pair STPÆ120 meters / 393ft.
◎Output Power : DC 5V/12V(selectable)
◎Data Transfer Rate :100Mbps/10Mbps
◎LED indicators : Connect to IEEE-802.3af PSE port
◎Temperature : 0℃to 45℃(Operating)
: -20℃to 90℃(Storage)
◎Humidity : 10% to 90% (Non-condensing)
◎Certifications : FCC Class A, CE Mark
◎Dimensions : 102 mm ×74 mm ×22 mm (L ×W ×H)
◎Weight : 240g

5
Chapter 2.
Package contents
Before you start to install the Splitter, please verify your package that contains the following items:
One Splitter
One Power output cable
One User’s Manual
Chapter 3.
Installation
I. The TP input port
Using this port to connect to the PSE port of PoE switch or Power injector Hub.
II. The TP output port
Using this port directly connect to the TP port of client device (i.e a soho switch, wireless Ap..)
III. The Power output port
Using the power jack cable to connect to the client device, supply 5V/12V to the client device
The LED indicators
LED Color Status Description
PSE Link Yellow On PSE connected

6
Chapter 4.
Application