Exsys EX-6074PoE User manual

1
Thank you for purchasing this Quad Channel PoE (PSE) Gigabit Ethernet PCI
Express Card. It is the fastest LAN host adapter available in the market that is
specially designed to connect 4 channel gigabit LAN interface to any computer with
PCIe (PCI Express, 4-lane) slots. It delivers isolated 48V DC power over Ethernet
cable for PoE (PD) devices. It also supports crossover detection and
auto-correction feature for the easy network cabling.
Features:
✓Supports 4 PoE (PSE) Gigabit Ethernet Ports
✓Integrated 10/100/1000 Transceiver
✓Supports PoE Specifications IEEE 802.3at Type 1 and 2
✓Microsoft NDIS5, NDIS6 Checksum Offload (IPv4, IPv6, TCP, UDP) and
Segmentation Task-offload (Large send v1 and v2) support
✓Supports Jumbo Frame to 9K bytes
✓Fully Compliant with IEEE 802.3 IEEE 802.3u, IEEE 802.3ab
✓Supports Win98SE, ME, 2K, XP, XP64, Vista, Win7, 8 and others
EX-6074PoE
4-Port PoE (PSE) Gigabit Ethernet PCIe Card
1. Introduction
2. Board and Bracket Layout
Link (Activity) LEDs
(Green)
J2:
Large 4-pin AUX
Power Connector
J3:
SATA15-pin AUX
Power Connector
RJ45 Connectors:
CH1
CH2
CH3
CH4
PoE On LEDs
(Yellow)

4-Port PoE (PSE) Gigabit Ethernet PCIe Card
2
Due to the hot-plug feature of the PCI Express, the installation of the PCIe Quad
Channel Gigabit Ethernet card is quite straightforward.
1. Turn the system power OFF before installation!
2. Use static electricity discharge precautions. To avoid damaging any
components on the card, handle it by edges.
3. Remove the chassis cover from your computer
4. Since this Card needs 12V to generate PoE power to its RJ45 connectors,
please connect power supply cable to J2 (large 4-pin type) or J3 (SATA
15-pin type) power connectors
5. Locate an unused PCI Express slot (typically white and smaller) and
remove the corresponding slot cover from computer chassis.
6. Plug the Quad Channel Ethernet PCIe card to the unused PCI Express
expansion slot and attached the I/O card bracket to the computer chassis
screw.
7. Put the chassis cover back on the computer.
8. Turn ON the power of your computer and peripherals.
9. Proceed with Software Driver Installation.
10. Installing LAN cables
Connect the LAN cables to both RJ45 connectors of the Quad Channel
Ethernet PCIe card. Please check the LEDs’status as follows:
The ‘LINK(ACT)’LED will light if link on. However, the same LEDs will flash
when transferring data.
The ‘PoE’LEDs will light up if a (PoE) PD is connected. In this case, the
48V DC power was applied on the LAN cable. Otherwise, if the ‘PoE’LED
is off, the device is not a (PoE) PD and the LAN cable does NOT carry 48V
DC power on it.

LED Name
Color
LED Function
LINK(ACT)
Green
Steady on: Linked
Blinking: Transferring Data
PoE
Yellow
Steady on: PoE Enabled.
Off: PoE Disabled.
3. Installing the Gigabit Ethernet PCIe Card

4-Port PoE (PSE) Gigabit Ethernet PCIe Card
3
The Gigabit Ethernet drivers are shipped in the following folder of the driver CD.
Please browse to the corresponding driver folder when Windows ask you to specify
the driver location. Then follow the on-screen instructions of the Windows to complete
the installation.
You can use Device Manager to check the installation. Here are the screen shots
showed you that it was installed correctly:
4 Gigabit Ethernet
ports shown here
4. Windows Driver Installation

4-Port PoE (PSE) Gigabit Ethernet PCIe Card
4
4 PCI-to-PCI bridge
devices appeared