Extraflame Elisir User manual

Elisir
Read the instructions carefully before installation, use and maintenance.
The instruction book is an integral part of the product.
User manual

2

3
Congratulations! You are now the owner of an Extraame stove!
The Extraame pellet stove is an ideal heating solution. It utilises the most advanced technology and is
manufactured to the highest standards with a contemporary design, allowing you to enjoy the ambience
and warmth of a natural ame in complete safety.
This manual tells you how to use your stove correctly. Please read the entire manual carefully before using
your stove.
IMPORTANT
Make sure that the dealer completes the following box with the details of the authorised specialist who
will help you if you have any problems in using your new pellet stove.
AUTHORISED SPECIALIST
COMPANY __________________________________________________________________
Full name __________________________________________________________________
Address ______________________________________________ No. __________________
Postal Code ____________ City __________________ County. ______________________
TEL. ________________________________ FAX __________________________________
All Extraame products are manufactured according to the following directives:
89/106 CEE (Construction Products)
89/366 CEE (EMC Directive)
2004/108 CE (EMC Directive)
2006/95 CE (Low Voltage Directive)
And the following standards:
EN 14785
EN 60335-1
EN 60335-2-102
EN 61000-3-2
EN 61000-3-3
EN 50366
EN 55014-1
EN 55014-2

4

5
Index
WARNINGS AND SAFETY DEVICES..............................................................................................................................................................................................7
Chapter 2
WHAT IS THE PELLET?................................................................................................................................................................................................................... 8
PELLET STORAGE...........................................................................................................................................................................................................................................................................8
PELLET FEEDING............................................................................................................................................................................................................................................................................ 8
Chapter 3
SAFETY DEVICES...........................................................................................................................................................................................................................9
HOT AIR DISTRIBUTION FAN BREAKAGE .............................................................................................................................................................................................................................9
PELLET FEED MOTOR BREAKAGE ...........................................................................................................................................................................................................................................9
NO IGNITION...................................................................................................................................................................................................................................................................................9
TEMPORARY POWER CUT.......................................................................................................................................................................................................................................................... 9
DOOR MICRO SWITCH ................................................................................................................................................................................................................................................................9
ELECTRIC SAFETY..........................................................................................................................................................................................................................................................................9
FLUE EXHAUST SAFETY DEVICE .............................................................................................................................................................................................................................................9
PELLET TEMPERATURE SAFETY DEVICE ..............................................................................................................................................................................................................................9
Chapter 4
ASSEMBLY AND INSTALLATION INSTRUCTIONS.....................................................................................................................................................................10
GLOSSARY......................................................................................................................................................................................................................................................................................10
INSTALLATION..............................................................................................................................................................................................................................................................................11
ALLOWED INSTALLATIONS ...........................................................................................................................................................................................................................................11
INSTALLATIONS NOT ALLOWED .................................................................................................................................................................................................................................11
CONNECTION TO THE SMOKE EVACUATION SYSTEM..................................................................................................................................................................................................12
SMOKE CHANNEL OR CONNECTIONS......................................................................................................................................................................................................................12
CHIMNEY OR INDIVIDUAL FLUE..................................................................................................................................................................................................................................13
APPLIANCE CONNECTION TO THE FLUE AND FUEL PRODUCTS EVACUATION.......................................................................................................................................15
CHIMNEY CAP.....................................................................................................................................................................................................................................................................15
CONNECTION TO EXTERNAL AIR INLETS...........................................................................................................................................................................................................................16
INSULATION, FINISHINGS, COVERING AND SAFETY RECOMMENDATIONS........................................................................................................................................................16
NATIONAL, REGIONAL, PROVINCIAL AND TOWN COUNCIL REGULATIONS .......................................................................................................................................................16
Chapter 5
HOT AIR DUCTING ......................................................................................................................................................................................................................17
ELISIR AIR INLET INSTALLATION...............................................................................................................................................................................................17
MECHANICAL THERMOSTAT FUNCTIONING FOR DUCTING MOTOR CONTROL ..............................................................................................................................................18
Chapter 6
PRODUCT FUNCTIONALITY.......................................................................................................................................................................................................19
CONTROL BOARD........................................................................................................................................................................................................................................................................19
FUNCTIONING CYCLE................................................................................................................................................................................................................................................................19
BASIC INSTRUCTIONS .....................................................................................................................................................................................................................................................19
RECOMMENDATIONS BEFORE IGNITION ................................................................................................................................................................................................................20
IGNITION...............................................................................................................................................................................................................................................................................20
FUNCTIONING....................................................................................................................................................................................................................................................................21
SWITCHOFF........................................................................................................................................................................................................................................................................21
INITIAL INSPECTION ........................................................................................................................................................................................................................................................21
Chapter 7
ROOM THERMOSTAT ..................................................................................................................................................................................................................22
DIGITAL THERMOSTAT AS PER STANDARD....................................................................................................................................................................................................................22
ADDITIONAL THERMOSTAT OPTIONAL...........................................................................................................................................................................................................................22
MECHANICAL THERMOSTAT INSTALLATION OPTIONAL..........................................................................................................................................................................................22
MECHANICAL THERMOSTAT FUNCTIONING FOR DUCTING MOTOR CONTROL .............................................................................................................................................22
Chapter 8
THE REMOTE CONTROL..............................................................................................................................................................................................................24
Chapter 9
ELISIR PRODUCT DISPLAY TABLES ...........................................................................................................................................................................................25
Chapter 1
ELISIR UTENTE PARAMETERS BOARD 002272575................................................................................................................................................................28
SET CLOCK......................................................................................................................................................................................................................................................................................28
CLOCK ADJUSTMENT RAPID MODE..........................................................................................................................................................................................................................29
SET CHRONO.................................................................................................................................................................................................................................................................................30
RAPID ACCESS MODE TO CHRONO...........................................................................................................................................................................................................................31
CHRONO MENU DISPLAY ........................................................................................................................................................................................................................................................32
LANGUAGE SETTING..................................................................................................................................................................................................................................................................33
LANGUAGE SETTING RAPID MODE...........................................................................................................................................................................................................................33
UTENTE............................................................................................................................................................................................................................................................................................34
DISPLAY SETTING RAPID MODE.......................................................................................................................................................................................................................34
PELLETS 20% +20%......................................................................................................................................................................................................................................................35
PELLET ADJUSTMENT RAPID MODE...............................................................................................................................................................................................................36
V1ARIA ................................................................................................................................................................................................................................................................................37
FRONT AIR ADJUSTMENT RAPID MODE V1ARIA ..................................................................................................................................................................................37
STANDBY: EXPLANATION.............................................................................................................................................................................................................................................38

6
STANDBY USE WITH EXTERNAL ADDITIONAL THERMOSTAT..............................................................................................................................................................38
STANDBY RAPID MODE......................................................................................................................................................................................................................................39
ACTIVATION OR DEACTIVATION OF STANDBY MODE............................................................................................................................................................................39
KEYS FROZEN......................................................................................................................................................................................................................................................................40
KEYS FROZEN RAPID MODE...............................................................................................................................................................................................................................40
AIR DUCTING RAPID MODE V2ARIA...........................................................................................................................................................................................................41
Chapter 2
ELISIR CLEANING ........................................................................................................................................................................................................................42
Chapter 3
RAPID MENUS .............................................................................................................................................................................................................................45
STOVE IGNITION ..........................................................................................................................................................................................................................................................................46
STOVE SWITCHOFF ...................................................................................................................................................................................................................................................................46
FUNCTIONING POWER CHANGE ..........................................................................................................................................................................................................................................46
ROOM TEMPERATURE................................................................................................................................................................................................................................................................46
CLOCK ADJUSTMENT ................................................................................................................................................................................................................................................................47
CHRONO .........................................................................................................................................................................................................................................................................................48
LANGUAGE SETTING..................................................................................................................................................................................................................................................................49
DISPLAY SETTING........................................................................................................................................................................................................................................................................49
PELLET SETTING ..........................................................................................................................................................................................................................................................................50
FRONT AIR V1AIR....................................................................................................................................................................................................................................................................50
STAND  BY.....................................................................................................................................................................................................................................................................................51
KEYS FROZEN................................................................................................................................................................................................................................................................................51
AIR DUCTING V2  ARIA..........................................................................................................................................................................................................................................................52
Chapter 4
WARRANTY CONDITIONS ......................................................................................................................53

WARNINGS AND SAFETY DEVICES 7
The stoves produced by our establishment are built with
attention to the individual components in a way to protect
both the user and the installer from any accidents. It is
therefore recommended that after any intervention on the
product, authorised sta pay particular attention to the
electric connections, especially the stripped parts of the
wires.These must not escape from the terminal board in any
situation, thus preventing possible contact with the live parts
of the wire.
Installation must be carried out by authorised sta, who
must provide the buyer with a declaration of conformity
for the system and will assume full responsibility for nal
installationandasaconsequence thecorrect functioning
of the installed product. It is necessary to bear in mind all
laws and national, regional, provincial and town council
Standards present in the country the appliance has been
installed.
Extraame S.p.A. cannot be held responsible for the
failure to comply with such precautions.
The instruction manual is an integral part of the product:
make sure that it always accompanies the appliance, even
if transferred to other owners or user or is transferred to
another place. If it is damaged or lost, request another copy
from the area technician.
This stove must be destined for the use for which it has been
expressly realised. The manufacturer is exempt from any
liability, contractual and extracontractual, for injury/damage
caused to persons/animals and objects, due to installation,
adjustment and maintenance errors and improper use.
After the packaging has been removed, check the integrity
and completeness of the contents. If this does not comply,
contact the dealer where the appliance was purchased.
All electric components that make up the stove must be
replacedwithoriginalsparepartsexclusivelybyanauthorised
after-sales centre, thus guaranteeing correct functioning.
The stove must be serviced at least once a year,
programming it in advance with the technical after-sales
service.
Nota bene: In case of thermo product or boiler, the
product or system venting is not covered by the
warranty.
For safety reasons, remember that:
The stove must not be used by children or unassisted
disabled persons.
Do not touch the stove when you are barefoot or when
parts of the body are wet or humid.
The safety and adjustment devices must not be
modied without the authorisation or indications of the
manufacturer.
Do not pull, disconnect, twist electric cables leaving the
stove, even if disconnected from the electric power supply
mains.
Do not close or reduce the dimensions of
the airing vents in the place of installation.
The airing vents are indispensable for correct combustion.
Do not leave the packaging elements within reach of
children or unassisted disabled persons.
The hearth door must always be closed during normal
functioning of the product.
Avoid direct contact with parts of the appliance that
tend to heat up during functioning.
Check for the presence of any obstructions before
switchingtheapplianceonfollowingaprolongedstandstill
period.
The stove has been designed to function in
any climatic condition (also critical). In particularly
adverse conditions (strong wind, freezing) safety
systems may intervene that switch the stove o.
If this occurs, contact the technical after-sales service and
always disable the safety system.
If the ue should catch re, be equipped with suitable
systems for suocating the ames or request help from the
re service.
MAJOLICAS
The company have chosen majolica tiles, which are the
result of high-quality artisan work and therefore the
majolica may present crackles, speckles, and shadings.
These characteristics certify their precious origin.
Enamel and majolica, due to their dierent coecient
of dilatation, produce microcrackles, which show their
authentic feature.
Forthe cleaningofthe majolicawesuggest you useasoft
and dry cloth; if you use a detergent or liquid, the latter
might soak in and make the crackles more visible.
WARNINGS AND SAFETY DEVICES

WHAT IS THE PELLET?
8
Chapter 2Chapter 2
WHAT IS THE PELLET?
Pellets are realised by subjecting wood shavings i.e. the rejects of pure wood (without paint) sawmill,
carpenter products and products from other activities connected to working and transforming wood, to
very high pressures.
This type of fuel is absolutely ecological as no glues are used to hold it together. In fact, the compactness
of the pellets is guaranteed through time by a natural substance that is found in wood: lignin.
As well as being an ecological fuel, as wood residues are made the most of, the pellet also has technical
advantages.
Pellet density is about 650 kg/m3 and water content is equal to 8% of its weight. For this reason the pellet
does not have to be seasoned in order to obtain a suciently adequate heat yield.
The pellet used must comply with the features described by the Standard:
Ö-Norm M 7135
DIN plus 51731
UNI CEN/TS 14961
Extraame recommends the use of pellets with a diameter of 6mm with its products.
ATTENTION!
THE USE OF EXPIRED PELLETS OR ANY OTHER MATERIAL DAMAGES THE FUNCTIONS OF
YOURSTOVEANDCANDETERMINETHEINVALIDITY OFTHEWARRANTYANDTHEANNEXED
RESPONSIBILITY OF THE MANUFACTURER.
PELLET STORAGE
To guarantee combustion without problems, the pellets must be kept in a dry place.
PELLET FEEDING
To feed the pellet open the tank lid located on the upper part of the stove and empty the bag of pellets
being careful they do not fall out.

SAFETY DEVICES 9
Chapter 3
SAFETY DEVICES
HOT AIR DISTRIBUTION FAN BREAKAGE
In case the fan stops for any reason, the stove automatically stops.
FLUE EXHAUST BREAKAGE
If the suction device stops, the electronic board immediately blocks the pellet supply.
PELLET FEED MOTOR BREAKAGE
If the motor reducer stops, the stove continues to function until the minimum cooling level is reached.
NO IGNITION
If a ame is not developed during the ignition phase, the appliance automatically attempts ignition again,
this time without pellet feeding.
If in this case also the ame has not developed, the appliance will signal the alarm relating to no ignition;
if machine re-ignition is attempted, this will show“ATTE” meaning“wait”, on the display.
This function reminds that before performing ignition, it must be ensured that the brazier is completely
free and clean.
TEMPORARY POWER CUT
After a brief power cut, the appliance re-ignites automatically. When there is no electricity, the stove may
give o a minimum amount of smoke inside the case for a period from 3 to 5 minutes. THIS DOES NOT
REPRESENT ANY RISK WITH REGARD TO SAFETY.
DOOR MICRO SWITCH
When the stove door is opened, a safety micro switch blocks fuel feeding.
ELECTRIC SAFETY
The stove is protected against strong current changes by a master fuse that is found in the rear part of the
stove. (2.5A 250V Delayed).
FLUE EXHAUST SAFETY DEVICE
An electronic pressure switch blocks stove functioning and takes it to alarm conditions.
PELLET TEMPERATURE SAFETY DEVICE
If there is overheating inside the feed-box this device blocks stove functioning; restoration is manual and
must be performed by an authorised technician.

ASSEMBLY AND INSTALLATION INSTRUCTIONS
10
Chapter 4
ASSEMBLY AND INSTALLATION INSTRUCTIONS
The installation must be in compliance with:
UNI 10683 (2005) heat generators fed with wood and other solid fuels: installation.
The chimneys have to be in compliance with:
UNI 9731 (1990) chimneys: classication based on thermal resistance.
EN 13384-1 (2006) chimneys thermal and uid-dynamics calculation method.
UNI 7129 point 4.3.3 Fire Department dispositions, local rules and prescriptions.
UNI 1443 (2005) chimneys: general requisites.
UNI 1457 (2004) chimneys: terracotta and ceramic inside pipes.
GLOSSARY
CLOSED HEARTH APPLIANCE
Heat generator which opening is only allowed through the loading of the fuel during use.
BIOMASS
Biological material, excluding the material incorporated in geological formation and transformed in fossil.
BIOFUEL
Fuel produced directly or indirectly by biomass.
CHIMNEY
Vertical pipe with the aim to collect and expel, at a convenient height from the ground, the fuel products
coming from only one appliance.
SMOKE CHANNEL OR CONNECTION
Pipe or connecting element between heat generator appliance and chimney to evacuate fuel products.
INSULATION
Together of devices and materials used to prevent the transmission of heat through a wall which separates
rooms with dierent temperature.
CHIMNEY CAP
Device positioned at chimney peak to ease the dispersion of fuel products in the atmosphere.
CONDENSATION
Liquid products which form when the fuel gas temperature is lower or equal to the water dew point.
HEAT GENERATORS
Appliance which allows to produce thermal energy (heat) through the rapid transformation, through
combustion, of the chemical energy of the same fuel.
GATE VALVE
Mechanism to amend the fuel gas dynamic resistance.
SMOKE EVACUATION SYSTEMS
Flue gas exhaust system independent from the appliance constituted by a tting or smoke channel,
chimney or individual ue and chimney cap.

ASSEMBLY AND INSTALLATION INSTRUCTIONS 11
Chapter 4
FORCED DRAUGHT
Air circulation by means of the fan activated by electric motor.
NATURAL DRAUGHT
Draught which determinates in a chimney/ue for eect of the volume mass dierence existing between
smoke (hot) and surrounding atmosphere air, without any mechanical intake aid installed inside it or at its
peak.
RADIATION AREA
Area immediately near the furnace in which the heat caused by combustion is diused, where there must
be no fuelling materials.
REFLUX AREA
Area where leaking of the fuel products is veried, from the appliance towards the installation room.
INSTALLATION
The installation must be preceded by checking the chimneys, ues or unload terminals positioning of
appliances similarly to:
No installation
Legal distances
Limitations disposed by local administrative regulations or particular authority prescriptions.
Conventional limitations deriving from apartment building, constraints or contracts.
ALLOWED INSTALLATIONS
Only appliances working softly respect to the room or which do not place the room in depression respect to
the external environment, can exist or be installed in the room where the heat generator will be installed.
Only in rooms for kitchen use are appliances for cooking food and relative hoods without extractor.
INSTALLATIONS NOT ALLOWED
In the room where the heat generator will be installed the following must not pre-exist or be
installed:
hoods with or without extractor
collective type ventilation pipes.
Shouldtheseappliances bein roomsadjacent, communicatingwith theinstallation room,the simultaneous
useofthe heatgenerator isforbidden, wherea risk existsof oneofthe tworooms beingplacedindepression
respect to the other.

45°
<45°
<
ASSEMBLY AND INSTALLATION INSTRUCTIONS
12
Chapter 4
CONNECTION TO THE SMOKE EVACUATION SYSTEM
SMOKE CHANNEL OR CONNECTIONS
To mount the smoke channels, non-ammable elements will have to be used, ideal for resisting fuel
products and their eventual condensing.
The use of exible metal and asbestos cement pipes to connect the appliances to the ue is forbidden,
even for pre-existing smoke channels.
There must be continuity between the smoke channel and the ue so that the ue does not lean on the
generator. The smoke channels must not cross rooms where the installation of the combustion appliances
is not allowed.
The mounting of the smoke channels must be carried out in order to guarantee smoke seal for the
appliance functioning conditions, limit the forming of condensate and avoid it being transported towards
the appliance.
The mounting of horizontal routes must be avoided.
For appliances where ceiling or wall non coaxial discharges respect to the appliance smoke outlet have to
be reached, the direction changes will have to realised using open elbows not higher than 45° (see gures
below).
Insulating
product
Flue
Inspection
For the heat generator appliances equipped with electric fan for expelling fumes, the instructions below
must be followed:
The horizontal routes will have to have a minimum upward slope of 3%
The length of the horizontal route must be minimal and, however, not higher than 3 meters
The number of direction changes including the one for eect of using the “T” element must not be
more than 4 (if 4 bends are used, use double wall piping with a diameter of 120 mm).
In any case, the smoke channels must seal the fuel and condensing products and be insulated if they pass
externally to the installation room.
The use of counterslope elements is forbidden.
The smoke channel must allow the recovery of soot or be brushed.
The smoke channel must be at constant section. Any section changes are only allowed at the ue
coupling.
gure 4.1 gure 4.2

BC
20 cm
A
ASSEMBLY AND INSTALLATION INSTRUCTIONS 13
Chapter 4
It is forbidden to have other air supply channels and pipes for plant engineering, especially if over-sized,
transit inside the smoke channels.The mounting of manual draught adjustment devices on forced draught
appliances is forbidden.
CHIMNEY OR INDIVIDUAL FLUE
The chimney or individual ue must respond to the following requisites:
seal the fuel products, waterproof and adequately insulated similarly to the use conditions;
be realised with materials which resist the normal mechanical stresses, heat, action of the fuel products
and any condensing;
have mainly vertical progress with deviations from the axis not higher than 45°;
be adequately distanced from fuel or ammable materials through air space or opportune
insulation;
Minimum 80 cm2
Floor-protection
REFERENCES Inammable
objects
Non-inammable
objects
A 200 100
B 1500 750
C 200 100
have preferably circular internal section: the square or rectangular sections must have round corners
with a radius not lower than 20 mm;
have constant internal section, free and independent;
have rectangular section with max. ratio between the sides of 1.5.
It is recommended that the smoke pipe be equipped with a collection chamber for solid materials and any
condensing situated under the smoke channel inlet, so that it can be easily opened and inspected from
airtight door.
gure 4.3 gure 4.4

< 3 m
3 - 5 %
< 3 m
45°
45°
ASSEMBLY AND INSTALLATION INSTRUCTIONS
14
Chapter 4
Inspection
Windproof
chimney cap
Flue
Inspection
Insulated
external
pipe
Inspection
Inspection
gure 4.5 gure 4.6
gure 4.7 gure 4.8

50 cm
< 5 m > 5 m < 5 m
5
0
H min
β
ASSEMBLY AND INSTALLATION INSTRUCTIONS 15
Chapter 4
APPLIANCE CONNECTION TO THE FLUE AND FUEL PRODUCTS EVACUATION
The ue must receive the discharge from only one heat generator.
The direct discharge towards closed spaces is forbidden, even with clear sky.
The direct discharge of the fuel products must be at roof and the smoke pipe must have the features
provided in the“Chimney or individual ue” section.
CHIMNEY CAP
The chimney cap must comply with the following requisites:
have an internal section equivalent to that of the chimney;
have useful outlet section not lower than double the chimney internal section;
be built in order to avoid rain, snow, foreign bodies penetrating the chimney and in order that, in case
of winds in any direction and inclination, the discharge of the fuel products is assured.
be positioned in a way to guarantee an adequate dispersion and dilution of the fuel products and,
however,outside thereuxarea inwhich theformationof counterpressuresoccurs.Such areahasdierent
dimensions and conguration depending on the covering inclination angle, it is therefore necessary to
adopt the minimum heights indicated in the gure layouts below.
The chimney cap must not have mechanical intake means.
SLOPING ROOF
FLAT ROOF
Distance > A
Distance < A
50 cm over the ridge
REFLUX AREA
reux area height
gure 4.9
gure 4.10

ASSEMBLY AND INSTALLATION INSTRUCTIONS
16
Chapter 4
CHIMNEY CAPS, DISTANCES AND POSITIONING
Roof
inclination
Distance between the
ridge and the chimney
Minimum chimney height
(measured from outlet)
β A (m) H (m)
15° < 1,85 0.50 m over the ridge
> 1,85 1,00 m from roof
30° < 1,50 0.50 m over the ridge
> 1,50 1,30 m from roof
45° < 1,30 0.50 m over the ridge
> 1,30 2,00 m from roof
60° < 1,20 0,50 m over the ridge
> 1,20 2,60 m from roof
CONNECTION TO EXTERNAL AIR INLETS
The appliance must be able to use the necessary air to guarantee regular functioning through external air
inlet. The air inlets must comply with the following requisites:
have a total free section of at least 80 cm.1.
must be protected by grates, metal net or suitable protections as long as they do not reduce the2.
minimum section stated in point 1 and positioned in order to avoid them being obstructed.
If the combustion agent air is withdrawn directly from outside through a pipe, a downward bend must be
mounted outside or a protection against the wind and no grids or similar must be positioned. (Even if the
air is withdrawn from outside through a pipe, it is necessary that the air vent always communicates directly
with the installation room).The air ow can also be obtained from an adjacent room to the installation one,
as long as the ow can happen freely through permanent openings communicating with the outside.
The adjacent room, respect to the installation one, must not be put in depression respect to the external
environment by means of reverse draught caused by the presence of another used appliance or intake
device in such room.The permanent openings in the adjacent room must comply with the above-described
requisites. The adjacent room cannot be set up as garage, storage for fuelling material or activity with
danger of re.
INSULATION, FINISHINGS, COVERING AND SAFETY RECOMMENDATIONS
The coverings, independently from the materials with which they are made, must constitute a self-
supporting construction respect to the heating block and not be in contact with it.
The wooden or fuelling materials beam and nishings must be positioned outside the hearth radiation
area or adequately insulated.
In case coverings in fuelling material or sensible to heat exist in the space above the generator, an insulating
and non fuelling protection diaphragm must be inserted.
Elements in fuelling or inammable material like wooden furniture, curtains, etc., directly exposed to the
hearth radiation, must be positioned at a safe distance. The appliance installation must guarantee easy
access for cleaning the same appliance, discharge gas pipe and ue.
NATIONAL, REGIONAL, PROVINCIAL AND TOWN COUNCIL REGULATIONS
It is necessary to bear in mind all laws and national, regional, provincial and town council Standards present
in the country the appliance has been installed.

HOT AIR DUCTING 17
Chapter 5
HOT AIR DUCTING
The gure represents as an example the dierent hot air ducting modalities.
The dierent ducting modalities must be discussed with the technician who will see to the installation.
It is recommended not to exceed the 2 metres in length and to use insulating material to avoid heat
losses.
ELISIR AIR INLET INSTALLATION
To install the air inlet we recommend reading the attached folder.
gure 5.1 gure 5.2 gure 5.3
gure 5.4

ELISIR AIR INLET INSTALLATION
18
Chapter 5
MECHANICAL THERMOSTAT FUNCTIONING FOR DUCTING MOTOR CONTROL
The connection of an external thermostat will allow to separate the stove functioning from the functioning
of the ducting motor.
At this point just set the desired temperature, the mechanical thermostat will control the functioning of
the second motor:
with temperature to be reached the second motor will follow the progress of the stove
when the temperature is reached it will take the 2nd motor to 1st speed, making the relative luminous
indicator on the control board ash.
casing clamps for additional thermostats connection
Front view right side
Casing clamps for additional thermostat
ducting
Casing clamps for additional thermostat
room
gure 5.5
gure 5.6

PRODUCT FUNCTIONALITY 19
Chapter 6
PRODUCT FUNCTIONALITY
CONTROL BOARD
REMOTE
CONTROL SENSOR D1 D2
1 DON/OFF BUTTON
By pressing button 1 it is possible to switch the stove on and o automatically.
2-3 DROOM TEMPERATURE SETTING
Buttons 2 and 3 are used to adjust the wanted room temperature inside the house.
4-5 DFUNCTIONING POWER
The heat power can be adjusted using buttons 4 and 5
Display D1 to view the various messages.
Display D2 to view the power set.
FUNCTIONING CYCLE
BASIC INSTRUCTIONS
The following recommendations must be followed the rst two or three times the machine is ignited:
It is possible that slight odours are produced due to the drying of the paints and silicones used. Avoid
long stays and air the room.
Do not touch the surfaces as they could still be unstable.
The hardening of the surfaces is terminated after several heating processes.
This appliance must not be used to burn waste.
gure 6.1

PRODUCT FUNCTIONALITY
20
Chapter 6
RECOMMENDATIONS BEFORE IGNITION
Before ignition the following points must be veried:
the feed-box must be full of pellets
the combustion chamber must be clean
The braziermust be completely free and clean
check the hermetic closure of the re door and the ash drawer
make sure the power supply cable is connected correctly
the bipolar switch in the rear right part must be positioned on 1
ATTENTION!!!
Do not use any inammable liquids for ignition
Do not allow the bag of pellets to come into contact with the boiling hot stove during the
lling phase
In the case of continuous no ignition, contact an authorised technician
IT IS PROHIBITED to burn non-pelletised raw materials inside our stoves.
The failure to comply with these prescriptions voids all guarantees and could jeopardise the
safety of the appliance.
The lid of the pellet container must always be closed. It must only be opened during the fuel
loading phase.
It is recommended that the feed-box is always half full.
During the lling phase do not allow the bag of pellets to come into contact with the
product
The bags of pellets must be kept at least 1.5 metres from the stove.
IGNITION
A. Press key 1 for 3 seconds.
Once time for ignition has passed (which can vary depending on the model) if the machine has not ignited,
the“no ignition” alarm occurs.
In the case of alarm due to no ignition, follow these points:
1. Wait a minimum of 10 minutes without pressing any button on the display, in the mean time clean the
brazier.
ATTENTION!
N.B. DO NOT PUT THE PELLETS BACK IN THE TANK FROM THE BRAZIER
2.Close the door
3.Press key 1 for 3 seconds.
If ignition takes place, the machine will automatically go into the third phase: start-up.
The passing from ignition phase to start-up is fully automatic.
N.B. As times are variable, there are no precise or dened times.