Extraflame EcoLogica Idro User manual

PELLET STOVES
Instruction Manual
Ecologica Idro
Read these instructions carefully before installation, use and maintenance.
The instruction booklet is an integral part of the product.

Page
2
Congratulations! You are now the owner of an EXTR FL ME stove!
The EXTRAF AME pellet stove is an ideal heating solution. It utilises the most advanced
technology and is manufactured to the highest standards with a contemporary design,
allowing you to enjoy the ambience and warmth of a natural flame in complete safety.
This manual tells you how to use your stove correctly. Please read the entire manual
carefully before using your stove.
IMPORT NT
Make sure that the dealer completes the following box with the details of the authorised
specialist who will help you if you have any problems in using your new pellet stove.
UTHORISED SPECI LIST
COMP NY________________________________________________________________
N ME _______________________________________________________________
DDRESS _____________________________________________________________
POST CODE ____________ CITY ____________________________________________
TEL. ________________________ F X _______________________________________
All Extraflame products are manufactured according to the following directives:
• 89/106 EEC (CPD) construction materials
• 73/23 EEC (LVD) electrical safety
• 98/37 EEC machinery
• 2004/108 EEC (EMC) electromagnetic compatibility
And the following standards:
• EN14785
• EN60335.1 EN50165 EN50366
• EN292 EN294
• EN55014.1 EN55014.2 EN61000-3-2 EN61000-3-3

Page
3
Contents
1 W RNINGS ND S FETY 4
2 TECHNIC L SPECIFIC TIONS 5
3 WH T RE PELLETS? 7
3.1 Pellet storage 7
3.2 Pellet loading 7
4 S FETY DEVICES 8
4.1 Breakdown of hot air distribution fan 8
4.2 Breakdown of flue gas extractor 8
4.3 Breakdown of pellet load motor 8
4.4 Failed ignition 8
4.5 Temporary power cut 8
4.6 Electrical safety device 8
4.7 Flue gas exhaust safety device 8
4.8 Pellet temperature safety device 8
4.9 System pressure safety device 8
4.10 Boiling water safety device 8
4.11 External devices 8
4.12 Installation and safety devices 9
4.13 Safety devices for open tank systems 9
4.14 Safety devices for closed tank systems 9
5 SSEMBLY ND INST LL TION INSTRUCTIONS 10
5.1 Glossary 10
5.2 Installation 11
5.2.1 Connection to the flue gas evacuation system 12
5.2.2 Chimney or flue 13
5.2.3 Connecting the appliance to the flue and evacuation of combustion products 15
5.2.4 Chimney 15
5.2.5 Connection to external air inlets 16
5.2.6 Insulation, trims, facings and safety recommendations 16
5.2.7 National, regional, provincial and municipal regulations 16
6 CONTROL P NEL 17
7 DJUSTING CURRENT TIME 18
8 USE 18
9 IGNITION 18
10 STOVE OPER TION 19
10.1 Normal operation 19
10.2 Switching-off 19
10.3 Remote control 20
11 ROOM THERMOST T 21
11.1 Digital thermostat (standard) 21
11.2 Mechanical thermostat (optional) 21
11.2.1 Installation of mechanical thermostat (optional) 21
11.2.2 Mechanical thermostat operation 21
11.2.3 Mechanical thermostat operation in Stby mode (to be used with remote actuator) 21
12 USER P R METERS 23
12.1 Water temperature adjustment 23
12.2 Weekly programmer 23
12.3 Day/night temperature function 26
12.4 Pellet load adjustment 28
13 CLE NING 29
13.1 Connection to the chimney 30
14 WIRING DI GR M 31
15 STOVE DISPL Y MESS GE T BLES 33
16 W RR NTY 36
17 QU LITY CONTROL 38
18 COMP TIBILITY WITH RoHS ND WEEE DIRECTIVES 39

Page
4
1. W RNINGS ND S FETY
The stoves produced in our factory are built with
maximum dedication to the individual components
so as to protect both the user and the installer
from accidents. Authorised personnel are therefore
advised to pay special attention to the electrical
connections, above all after any servicing
operation on the product, especially with regard to
the stripped part of the wires, which must not
protrude in any way from the terminal block to
prevent possible contact with the live parts of the
wire.
Installation must be carried out by
authorised personnel, who have to provide a
declaration of conformity of the appliance
for the purchaser, who will then be fully
responsible for the permanent installation
and consequent correct operation of the
installed product. It is necessary to bear in
mind all the national, regional, provincial
and municipal laws and regulations present
in the country in which the appliance is
installed.
Extraflame S.p. . may not be held
responsible in the event of failure to observe
these precautions.
This instruction manual constitutes an integral part
of the product. It must always accompany the
appliance, also when it is transferred to another
owner or user or moved to another location. If the
manual gets damaged or lost, ask your local
service centre for another copy.
This stove must only be used for the applications
for which it was expressly designed.
The manufacturer declines any responsibility,
contractually or extra-contractually, for any
damage caused to persons, animals or property by
errors in installation, adjustment, and
maintenance, or by improper use.
After removing the packaging, check to make sure
that the contents are intact and complete.
If this is not the case, contact the vendor from
whom the appliance was purchased .
The electrical components of the stove, to
guarantee correct operation, must only be
replaced with original spare parts from an
authorised service centre.
General stove maintenance must be carried out at
least once a year, scheduled sufficiently in advance
with the service centre.
The following safety precautions must be
observed:
Do not allow the stove to be used by children or
unassisted disabled persons.
Do not touch the stove if you are bare-footed or if
parts of your body are wet or damp.
Modifying the safety or adjustment devices without
the manufacturer’s approval or instructions is
forbidden.
Never pull, detach, or twist the electrical cables
coming out of the stove, even if it is disconnected
from the electrical power supply.
Avoid blocking up or reducing the size of the air
vents of the room in which the stove is installed.
The air vents are critical for correct combustion.
Keep the packaging materials out of the reach of
children and unassisted disabled persons.
During product operation the door of the furnace
must always be closed.
Avoid direct contact with parts of the appliance
which tend to heat up during functioning.
Check for the presence of any obstructions before
switching the appliance on following a long
standstill period.
The stove has been designed to function in any
climatic conditions (even critical), in particularly
adverse conditions (strong wind, ice) safety
systems may intervene, which switch the stove off.
If this happens, contact the after-sales service and
under no circumstances disable the safety systems.
If the flue should catch fire use suitable systems to
suffocate the flames or request help from the fire
brigade.

Page
5
2. TECHNIC L SPECIFIC TIONS
Valore
Features Unit
Value
Weight kg 159
Height mm 955
Width mm 667
Depth mm 671
Flue gas exhaust pipe diameter mm 80
Air extraction pipe diameter mm 50
Max. overall thermal power kW 16
Max. useful thermal power kW 12.5
- output air power kW 1.0
- output water power kW 11.5
Min. useful thermal power kW 3.5
- output air power kW 0.5
- output water power kW 3.0
Min. hourly fuel consumption kg/h
0.8
Max. hourly fuel consumption kg/h
3.2
Tank capacity kg ~ 30
Recommended chimney draught Pa ~ 10
Chimney draught at max useful power Pa 12
Chimney draught at min useful power Pa 10
Rated electrical power W 310
Rated voltage Vac 230
Rated frequency Hz 50
Water inlet/outlet pipe diameter “ 3/4
Automatic discharge pipe diameter “ -
Pump head m 4
Max accepted working water power bar 1.5
CO measured at max useful power % 0.024
CO measured at min useful power % 0.033
Efficiency at max useful power % 80.8
Efficiency at min useful power % 91.5
Exhaust gas temp. at max useful power °C 214
Exhaust gas temp. at min useful power °C 76.8
Mass of gases emitted at max useful power g/s 15.17
Mass of gases emitted at min useful power g/s 6.38
Tests carried out using wooden pellets as fuel, with calorific value of 4.9 kW/h/kg.
The data stated above is a reference and not binding. The manufacturer reserves the right to carry
out any modifications in order to improve the performance of the product.

Page
6

Page
7
3. WH T RE PELLETS?
Pellets are made by applying very high pressure to sawdust; i.e. the residue of raw timber
(without paint) produced by sawmills, carpentry works and other activities involved in processing
wood.
This type of fuel is completely environmentally friendly, as no binders of any kind are used to keep
it compact. In fact, the compactness of the pellets over time is guaranteed by lignite, a natural
substance found in the wood itself.
As well as being an environmentally friendly fuel, since wood residues are exploited to the
maximum, pellets also have technical advantages.
While the heating power of wood is 4.4 kW/kg (with 15% humidity, after about 18 months
seasoning), the power of pellets is 5.3 kW/kg.
The density of the pellet is 650kg/m
3
and the water content is 8% of its weight. For this reason,
pellets do not need to be seasoned to obtain a sufficient heating yield.
The pellet used must conform to the characteristics of the following regulations:
•Ö-Norm M 7135
•DIN plus 51731
•UNI CEN/TS 14961
Extraflame recommends always using 6 mm pellets for its products.
3.1 Pellet storage
To guarantee problem-free combustion, the pellets must be stored in a dry place.
3.2 Pellet loading
To load the pellets, open the tank cover positioned on the upper part of the stove and empty the
bag of pellets, paying attention not to let them escape.
W RNING
THE USE OF POOR QUA ITY PE ETS OR ANY OTHER MATERIA MAY DAMAGE YOUR STOVE
AND MAY EAD TO THE INVA IDATION OF THE WARRANTY AND THE RE ATED
RESPONSIBI ITIES OF THE MANUFACTURER.

Page
8
4. S FETY DEVICES
4.1 Breakdown of hot air distribution fan
If the blower stops for any reason, the stove automatically shuts down to prevent overheating
4.2 Breakdown of flue gas extractor
If the extractor stops, the electronic unit immediately prevents pellet feeding.
4.3 Breakdown of pellet load motor
If the motor stops, the stove continues to operate until the minimum cooling level is reached.
4.4 Failed ignition
If no flame develops during the ignition phase, the appliance automatically attempts a new ignition, this
time, though, without loading pellets.
If, after this attempt, the stove still has no flame, the stove display shows “FAI ED IGNITION”. If you
attempt to light the stove again, the display shows “COO ING WAIT” which means “WAIT”.
This function reminds you that before lighting the stove, you must be sure that the brazier is
free of dirt and debris.
4.5 Temporary power cut
The appliance will re-light automatically after a brief power failure. When the power goes off, the stove may
emit a minute quantity of smoke inside the house for a period of 3 to 5 minutes.
THIS DOES NOT POSE ANY SAFETY RISK.
4.6 Electrical safety device
The stove is protected against violent changes in power by a master fuse on the rear of the stove (2A 250V
delayed).
4.7 Flue gas exhaust safety device
If the exhaust system fails, an electronic pressure switch stops the stove and an alarm is signalled.
4.8 Pellet temperature safety device
In case of overheating inside the pellet tank, this safety device blocks stove operation; resetting is manual
and must be performed by an authorised technician.
4.9 System pressure safety device
A mechanical pressure switch blocks any over-pressure in the system.
Resetting is manual and must be carried out by an authorised technician.
4.10 Boiling water safety device
In the event of a lack or minimum quantity of water, this device blocks the pellet feed. Reset is manual and
must be carried out by an authorised technician.
4.11 External devices
During stove installation, it is MANDATORY to adapt the system with a pressure gauge for viewing the water
pressure and an automatic discharge valve calibrated at 3 bar pressure.

Page
9
4.12 Installation and safety devices
The installation and respective system connections, the start-up and final testing for correct operation must
be carried out with all due diligence by authorised professional technicians (Italian aw no. 46 of 5 March
1990), in full respect for the regulations in force, both national and regional, as well as for the instructions
given in this manual.
Extraflame S.p. . declines any responsibility for damage to objects and/or persons caused by
the system.
4.13 Safety devices for open expansion tank system
According to the UNI 10412-2 (2006) regulation, in force in Italy, systems with open expansion tank must be
equipped with:
•Open expansion tank
•Safety tube
•oading tube
•Thermostat for circulator control (excluded for systems with natural circulation)
•Circulation system (excluded for systems with natural circulation)
•Device for acoustic alarm activation
•Acoustic alarm
•Temperature indicator
•Pressure indicator
•Automatic cut-out switch (cut-out thermostat)
The temperature safety sensors must be on-board the heat generator or at a distance no greater than 30 cm
from the delivery connection.
If the heat generators are not equipped with all the devices, the missing ones can be installed on the
delivery piping of the generator, at a distance of no more than 1 m from it.
4.14 Safety devices for closed tank system
According to the UNI 10412-2 (2006) regulation, in force in Italy, closed systems must be equipped with:
•Safety valve
•Circulator control thermostat
•Acoustic alarm activation thermostat
•Temperature indicator
•Pressure indicator
•Acoustic alarm
•Automatic thermal adjustment switch
•Automatic thermal cut-out switch (cut-out thermostat)
•Circulation system
•Expansion system
•Safety dissipation system incorporated into the generator with the blowdown valve (self-operated),
if the appliance is not equipped with a self-regulating temperature system
The temperature safety sensors must be on-board the heat generator or at a distance no greater than 30 cm
from the delivery connection.
If the generators are not equipped with all the devices, the missing ones can be installed on the delivery
piping of the generator, at a distance of no more than 1 m from the machine.
Domestic type automatic loading heating appliances must be equipped with a fuel blocking thermostat or a
cooling circuit provided by the manufacturer of the appliance, activated by a thermal safety valve in order to
guarantee that the temperature limit imposed by the regulation is not exceeded. The connection between
the power supply unit and the valve must not have interceptions. The pressure upstream from the cooling
circuit must be at least 1.5 bar.

Page
10
5. SSEMBLY ND INST LL TION INSTRUCTIONS
The installation must comply with:
UNI 10683 (2005) heat generators fed with wood and other solid fuels: installation.
The chimneys must comply with:
UNI 9731 (1990) chimneys: classification according to thermal resistance.
EN 13384-1 (2006) calculation method of the thermal and fluid-dynamic features of the chimney.
UNI 7129 point 4.3.3 provisions, local rules and prescriptions of the fire brigade.
UNI 1443 (2005) chimneys: general requirements.
UNI 1457 (2004) chimneys: internal ducts in terracotta and ceramics.
5.1 Glossary
CLOSED HE RTH DEVICE
Heat generator that can only be opened to load fuel during use.
BIOM SS
Material of organic origin, excluding the material incorporated in geological formations and
fossilised.
BIOFUEL
Fuel produced directly or indirectly from biomass.
FLUE or CHIMNEY
Vertical pipe for collecting and expelling combustion products from a single appliance at a suitable
height from the floor.
EXH UST PIPE or FITTING
Pipe or connecting element between the heat generating device and the chimney for extracting
the combustion products.
INSUL TION
The series of measures taken and materials used to prevent heat transmission through a wall
dividing rooms at different temperatures.
CHIMNEY C P
Device located at the top of the chimney that facilitates dispersion of the combustion products in
the atmosphere.
CONDENS TE
iquid products that form when the temperature of the combustion gas is lower than or equal to
the dew point of the water.
HE T GENER TOR
Device that permits the production of thermal energy (heat) by the rapid transformation of the
chemical energy of the fuel by means of combustion.
IR LOCK
Mechanism for modifying the dynamic resistance of the combustion gases.

Page
11
FLUE G S VENTING SYSTEM
A system for flue gas exhaust venting that is independent from the appliance, composed of a pipe
or channel, chimney or single flue, and chimney cap.
FORCED DR UGHT
Air circulation by means of a fan driven by an electric motor.
N TUR L DR UGHT
Draught resulting in a chimney/flue due to the difference in the volume mass existing between the
(hot) fumes and the surrounding atmospheric air, without any mechanical suction aid installed
inside or on top of it.
R DI NCE RE
Area immediately adjacent to the hearth in which the heat produced by combustion is diffused;
this area must not contain any objects made of combustible material.
REFLUX RE
Area in which the combustion products come out from the appliance towards the room in which it
is installed.
5.2 Installation
Before carrying out installation, it is necessary to check the positioning of the chimneys, flues or
exhaust terminal ducts of the appliance, bearing in mind the following:
•Installation prohibitions
•egal clearances
•imitations set out by local administrative regulations or specific regulations of the
authorities.
•Common limitations deriving from building regulations, and easement or contract
regulations.
dmissible installations
In the room in which the heat generator is to be installed, any existing or installed appliances must
be airtight to the room and must not cause depression in the room with respect to the external
environment.
Appliances used for cooking foods and the related hoods without extractor can only be installed in
rooms used as kitchens.
Prohibited installations
The room in which the heat generator is to be installed must not contain any of the following
devices, either pre-existing or installed:
- Hoods with or without extractor;
- Ventilation ducts of the collective type.
Should these devices be located in adjacent rooms communicating with the installation room, it is
forbidden to use the heat generator simultaneously where there is the risk that one of the two
rooms may be subject to depression with respect to the other.

Page
12
5.2.1 Connection to the flue gas venting system
Exhaust pipe or fitting
For the assembly of the exhaust pipes it is imperative to use non-flammable materials that are
resistant to combustion products and any condensates.
It is forbidden to use flexible metal pipes and asbestos cement for connecting the stove to the
flue, also for pre-existing exhaust channels.
There must be continuity between the exhaust pipe and the flue so that the flue does not lean on
the stove.
The exhaust pipes must not pass through rooms in which the installation of combustion devices is
forbidden.
The assembly of the exhaust pipes must be carried out in such a way as to ensure that they are
airtight for the operating conditions of the appliance, as well as to limit the formation of
condensates and prevent them from being conveyed towards the appliance.
The assembly of horizontal sections must be avoided where possible.
Where roof or wall exhaust outlets have to be reached that are not coaxial in relation to the
exhaust outlet from the appliance, the direction changes must be made using open elbows no
greater than 45° (see figures below).
For heat generating devices equipped with an electric exhaust fan, i.e. all products made by
Extraflame, it is necessary to observe the following instructions:
•Horizontal sections must have a minimum slope of 3% upwards.
•The length of the horizontal section must be as short as possible, and in any case no
greater than 3 metres.
•No more than four direction changes may be used, including the one resulting from the use
of the “T”-element. (When four bends are used, use double wall piping with a 100 mm
diameter.)
In any case, exhaust pipes must be sealed in relation to combustion products and condensates, as
well as insulated, if they pass outside the installation room.
It is forbidden to use elements in counter-slope.
The exhaust channel must allow soot recovery and cleaning using a swab.
The exhaust channel must have a constant cross-section. Any changes in cross-section are allowed
only at the flue connection. It is forbidden to run other air feed channels or piping for utilities
inside the exhaust channels, even if they are oversized. No manual draught regulation devices can
be mounted on forced draught appliances.
45°
45°
Insulation
Flue
Inspection

Page
13
5.2.2 Chimney or single flue
The chimney or flue must meet the following requirements:
- be sealed to combustion products, waterproof and properly insulated according to the usage
conditions;
- be made of materials suitable to resist normal mechanical stress, as well as heat and the action
of combustion products and any condensates;
- have a predominantly vertical layout with deviations from the axis no greater than 45°;
- be situated at a proper distance from combustible or flammable materials by means of an air gap
or suitable insulation material;
REFERENCES Flammable
objects
Non-flammable
objects
A 200 100
B 1500 750
C 200 100
- preferably have a round internal section: square or rectangular sections must have rounded
edges with radius no less than 20 mm;
- have a constant, free and independent internal section;
- have rectangular sections with a maximum ratio between sides of 1.5.
The exhaust pipe should be equipped with a chamber for the collection of solid materials and any
condensates located below the mouth of the exhaust pipe, so that it is easy to open and inspect
from the airtight hatch.
Minimum 80 cm²
Flooring prote
ction
B
20 cm
C

Page
14
Maximum 3 m
cm
3
–
5 %
Inspection
Windproof
chimney cap
Flue
Inspection
External
insulated duct
Inspection
Maximum 3 m
cm
45°
Inspection

Page
15
5.2.3 Connecting the appliance to the flue and evacuation of combustion products
The flue must receive exhaust from a single heat generator.
Direct discharge towards enclosed areas, even when roofless, is forbidden.
Direct discharge of combustion products must take place on the roof and the exhaust pipe must
have the features set out in the section “Chimney or single flue” .
5.2.4 Chimney cap
The chimney cap must meet the following requirements:
- have an internal section equivalent to that of the chimney;
- have a useful outlet section no less than twice the internal section of the chimney;
- be constructed in such a way as to prevent the penetration of rain, snow and foreign bodies into
the chimney, as well as to assure the discharge of the combustion products also in the presence of
winds coming from any direction and at any angle.
- be positioned in such a way as to assure proper dispersion and dilution of the combustion
products and, in any case, outside the reflux area in which the formation of counter-pressure is
most likely to occur. This area has different sizes and shapes depending on the slope of the roof;
therefore, it is necessary to use the minimum heights indicated in the figures below.
The chimney cap must not have any mechanical suction devices.
50 cm
> 5 m
< 5 m
50 cm
< 5 m
FL T ROOF
SLOPING ROOF
Distance
>
Distance
<
50 cm beyond the ridge beam
H min
β
REFLUX RE
Reflux area height

Page
16
CHIMNEYS, DIST NCES ND POSITIONING
Roof pitch Distance between the
crown and the chimney
Minimum height of the chimney
(measured from the outlet)
β (m) H (m)
15° < 1.85 0.50 m beyond the crown
> 1.85 1.00 m from the roof
30° < 1.50 0.50 m beyond the crown
> 1.50 1.30 m from the roof
45° < 1.30 0.50 m beyond the crown
> 1.30 2.00 m from the roof
60° < 1.20 0.50 m beyond the crown
> 1.20 2.60 m from the roof
5.2.5 Connection to external air inlets
To ensure correct operation, the appliance must have sufficient air available by means of external
air inlets, which must meet the following requirements:
a) They must have a total free section of at least 80 cm².
b) They must be protected by a grate, metal mesh, or other suitable protection provided that it
does not reduce the minimum section as per point a) and that it is positioned in such a way as to
prevent the intakes from being obstructed.
If the combustion air is collected directly from the outside by means of a pipe, it is necessary to fit
a downward bend or a wind hood on the outside. In addition, no grating or similar device should
be positioned. (Extraflame S.p.A. suggests creating an air intake directly communicating with the
installation room, even if air is collected from outside by means of a pipe). Air inflow can also be
obtained from a room adjacent to the installation room, provided that the flow can occur freely
through permanent openings communicating with the outside.
The adjacent room must not be subject to depression with respect to the outside as a result of the
opposing draught caused by the presence of another utility device or suction device in this room.
In the adjacent room, the permanent openings must meet the requirements described above.
The adjacent room cannot be used as a garage, storage area for combustible material, or for
activities involving fire hazards.
5.2.6 Insulation, trims, facings, and safety precautions
The facings, no matter what type of material they are made of, must constitute a self-bearing
structure with reference to the heating assembly and not in contact with it.
The beam and the trims in wood or combustible materials must be positioned outside of the
radiant area of the hearth or be properly insulated.
If the space above the heat generator has coverings made of combustible or heat-sensitive
material, a protective membrane made of non-combustible insulating material must be placed
between it and the generator.
All elements made of combustible or flammable material, such as wooden furnishings, curtains,
etc., which are directly exposed to the radiance of the hearth, must be placed at a safe distance.
The installation of the appliance must guarantee easy access for cleaning the appliance itself, of
the exhaust gas pipes and the flue.
5.2.7 National, regional, provincial and municipal laws
All the national, regional, provincial ad municipal laws of the country where the appliance has been
installed must be taken into consideration

Page
17
6. CONTROL P NEL
1  ON/OFF BUTTON
The stove can be turned on and off automatically by pressing button 1.
2-3  IR TEMPER TURE SETTING
Buttons 2 and 3 are used to adjust the room temperature inside the house.
4-5  OPER TING POWER
Buttons 4 and 5 are used to adjust the heating power and warm air ventilation.
D1 Display for showing the various messages
D2 Display for showing the heat setting
REMOTE CONTRO SENSOR
D1
D2

Page
18
7. CURRENT TIME ND D Y SETTINGS
To adjust these parameters follow the procedure below:
1. Disconnect and reconnect the power supply from the stove using the master switch or the
power cable.
2. The stove will firstly visualise the microprocessor version (Id_40 or later), “TIME”, “Li 3”
and then “OFF”.
3. When “TIME” appears, press button 5 to access the adjustment mode.
4. Display D1 will show the current time, the hours flash while the minutes are fixed: use
keys 2 and 3 to adjust the hours and then confirm using key 5.
5. At this point the hours are fixed and the minutes will start to flash: using keys 2 and 3,
adjust the minutes.
To go back to hour selection press button 4 again or exit and confirm using key 1.
8. USE
B SIC INSTRUCTIONS
The stove you have purchased uses pellets as fuel. This type of material is produced from natural
waste from woodworking. By means of a special process, which does not require the use of any
binders or additives, the shavings are compressed in industrial machines under high pressure and
become solid wooden pellets. IT IS STRICT Y FORBIDDEN to burn any other material besides
pellets in our stove.
Failure to respect these instructions will void all warranties and may jeopardise the safety of the
appliance.
The first two or three times the stove is lit, the following recommendations should be observed:
•No children should be present, as the vapours emitted can be harmful for health. Adults,
too, should not stay in the vicinity for very long.
•Do not touch the surfaces, as they could still be unstable.
•Air the room thoroughly several times.
•The hardening of the surfaces is completed after several heating processes.
•This stove must not be used as a waste incinerator.
9. IGNITION
1. Before proceeding, check to make sure that:
a. the tank is loaded with pellets
b. the combustion chamber is clean
c. the brazier is clean and free
d. the fire door and the ash drawer are sealed
e. the power cable is connected correctly
f. the two-way switch on the back of the stove is in position 1
2. Press button 1 for three seconds; display D1 will show the message “ t 08”, with the
numbers decreasing every second. During this stage, the stove carries out an automatic
check on the efficiency of each single electrical component. When this cycle is completed,
display D1 shows the message c 15 (the number of minutes for which the stove
attempts the lighting stage, decreasing by 1 every minute that passes).

Page
19
NOTE: The first time the stove is used, even if the tank is loaded with pellets, it is possible
that the pellets are not distributed to the combustion chamber for the first 15 minutes
because the worm screw for loading the pellets is empty. If the stove has not developed a
flame after the fifteen minutes have elapsed, the display shows the message “NO CC”.
In this case, press button 1 for three seconds until D1 shows the message “OFF”. Then
repeat steps 1 and 2.
3. If steps 1 and 2 are carried out correctly, as soon as the flame develops the stove enters
the start-up phase (“ u 07”).
4. After the start-up phase, the stove goes into normal operation: display D1 shows the room
temperature and D2 shows the heat setting.
W RNING!
1. NEVER USE FL MM BLE LIQUIDS FOR LIGHTING.
2. WHEN FILLING, DO NOT BRING THE S CK OF PELLETS INTO CONT CT WITH THE
HOT STOVE.
N.B.: In the event of continued lighting failures, contact an authorised technician .
10. STOVE OPER TION
10.1 Normal operation
Once the stove is lit, you can adjust the heat setting using buttons 4 and 5. Pressing button 4
decreases the heat setting and hourly pellet consumption; pressing 5 increases them. In addition
to the feed rate, the room temperature can be set directly from the control panel using button 2
and 3. To set the water temperature of the system, see the “ Water temperature adjustment ”
chapter.
The stove adjusts itself automatically in relation to the warm air ventilation.
The contents of the tank should be monitored to prevent the flame going out due to a lack of fuel.
TTENTION!
1. The cover of the pellet container must always be kept closed except when loading
fuel.
2. The sacks of pellets must be kept at least 1.5 metres away from the stove.
3. The tank should always be kept at least half full.
4. Before refilling, make sure that the appliance is switched off.
10.2 Shutdown
Press button 1 for three seconds.
When the three seconds have elapsed, the stove automatically starts the shutdown stage, cutting
off the pellet feed. Display D1 shows the message “OFF”, the current time, and the room
temperature in alternation.
Both the exhaust motor and warm air ventilation motor continue to run until the stove temperature
has dropped sufficiently.

Page
20
10.3 Remote control
The heat setting, the room temperature, and automatic start/stop of the stove can be remote
controlled.
S = ight that indicates which keys have
been pressed.
Correspondence of display keys with
remote control keys
1 = p3+p5
2 = p2
3 = p3
4 = p4
5 = p5
To light the stove, press buttons 3 and 5 at the same time and hold for three seconds (Fig. 21);
the stove automatically enters the lighting stage. This is followed by the start-up phase, which
allows the stove to develop and settle the flame.
When the lighting stage is complete, the stove goes into normal operation. The heat setting can
be adjusted using the buttons 4 and 5, and the room temperature setting can be adjusted using
buttons 2 and 3.
To switch off the stove, press buttons 3 and 5 at the same time and hold for three seconds.
Display D1 will show the message “OFF”.
The remote control operates with an MN21 12V battery (the kind used for gate opening remote
controls).
To replace the batteries, open the cover in the rear part as illustrated below.
Open by pressing the part circled in the figure
P3
P4
P2
P5
S