
17
fastening plate, with the hole directed to the
centre. Use the fixing media most suited to the
type of ground on which you intend to install the
Pantagruel table.) to the leg with 2 bolts M8x25.
Repeat this for all the legs.
3. Secure the legs to the tabletop with 4 bolts
M10x30 each.
4. Turn the table and loosen the Lazy Susan by
unscrewing the nut on the bottom of the tabletop
and by removing the stainless steel plate.
5. Remove the Lazy Susan.
6. Assemble the wheels to the axles with 4 bolts
M6 x 20 and flat washers M6. Use a 13 wrench
when tightening the bolts to secure the axle.
Attention: tighten the bolts, but do not fully
tighten them so the wheels can still rotate freely.
7. Put the Lazy Susan and the stainless steel disk in
the tabletop. Optional Lazy Susan anchoring: If
you would like to anchor the Lazy Susan, you can
assemble the stainless steel plate again on the
bottom of the tabletop. Use the extra lock nut
instead of the regular nut. This is a sustainable
solution. Do not tighten the extra lock nut too
much so the lazy susan can still rotate freely.
Pantagruel (high) table + Inumbra - p10
1. Remove the Lazy Susan and the little disk.
2. Put the Inumbra insert in the hole in the middle
of the tabletop. Make sure that its conical part
is facing upwards. Fasten the insert to the table,
putting the bolts through the bottom of the table.
3. Put the Lasy Susan back.
4. Place the Inumbra on the stainless steel tube
and fasten it by inserting the handle provided
into the lowest hole of the tube and tightening
it. Now open the parasol by inserting the handle
into the highest hole in the tube and turning it.
The parasol should always be fully opened or
completely closed.
Pantagruel table + Inumbrina - p12
1. Remove the Lazy Susan and the little disk.
2. Remove the rotary knob from the connector.
3. Put the Inumbrina 38 insert in the hole in the
middle of the tabletop. Make sure that the
cylindrical part is facing downwards and the
square plate is facing upwards. Fasten the insert
to the table, putting the bolts through the bottom
of the table.
4. Put the Lasy Susan back and insert the Inumbrina
into the table.
5. Reattach the rotary knob to the connector.
6. Lock it by tightening the adjuster screw
clockwise. The Inumbrina is only properly locked
into place if it can no longer spin on its axis.
7. a. To open the parasol, pull hard on the rope until
the crown meets the bolt.
b. To close it again, hold the rope at an angle as
you release it. TIP: continue to hold the rope at
an angle until the parasol is completely closed.
The parasol should always be fully opened or
completely closed.
8. Now insert the rope into the provided hole in the
parasol tube.
MAINTENANCE
Wood
DAY TO DAY CLEANING
Clean regularly and after every use
Wood doesn’t need much maintenance, but the
better you treat it, the longer it will last. Cleaning
the wood regularly and immediately after use with
a damp cloth will prevent fluids from penetrating
deep into the wood. An oiled table will absorb liquids
less quickly, keeping it clean for longer. To remove
stubborn remains of dirt, simply use a sti brush
and some water. Be careful not to permanently
damage the fibres. For this reason, never ever use a
high-pressure cleaner to clean wood.
CLEANING
Once or twice a year
Depending on the weather conditions, wood needs
a descent polish at least once a year. We would
recommend to do this before Spring and before
Winter, if your furniture is outside the whole year
round. Pick one of those humid, cloudy days, as it
is better for the moisture level in the wood to dry out
slowly after cleaning. For a thorough cleaning, we
can recommend our Extremis Wood Cleaner. This
is a bio-degradable cleansing shampoo for wooden
furniture. The product removes grey discolouration,
green deposits and dirt. Should any cracks appear,
you can simply sand them down by hand using 80
grit sandpaper.
OILING
Once a year
You are free to protect your wood from UV, inclement
weather and stains. Needless to say we strongly
recommend to do this once a year. Extremis Wood
Protector is a 100% natural product based on linseed
oil. It is colourless, but the wood will be darker
after this treatment. 0. Remove all residues of old
applications.
MACHINE SANDING
Only every 2 to 4 years
After a few years, there will be little cracks and ma-