Extremis kosmos User manual

KOSMOS
© design by dirk wynants
PRODUCT
KOSMOS – KOSMOS WITH PARASOL – FREESTANDING TABLE –
MAINTENANCE
READ INSIDE
ASSEMBLY INSTRUCTIONS,
HOW TO USE, USEFUL TIPS
FOR KEEPING YOUR TOOL FOR
TOGETHERNESS IN SHAPE
LANGUAGES
EN – NL – DE – FR – IT – ES
MORE
WWW.EXTREMIS.BE

2 inhoud
content p. 3
assembly kosmos p. 6
assembly with kosmos shade p. 8
adjusting adjustable table p. 10
covers p. 11
bulb replacement p. 12
onderhoud p. 13
assembly freestanding table p. 14
inhoud p. 17
montage kosmos p. 20
montage met kosmos shade p. 22
bijregelen verstelbare kabel p. 24
montage hoezen p. 25
lamp vervangen p. 26
onderhoud p. 27
monatage vrijstaande tafel p. 28

INHOUD
english 3
6 x bolt M6x14 6 x lock nut M6 5 x bolt M4x10 8 x bolt M6x12
3 x small backrest cushion
(low / high)
6 x bolt M8x80 6 x nut M8
2 x large seating cushion 1 x small seating cushion 4 x large backrest cushion
(low / high)
1 x adjustable table leg
xed table leg
1 x tabletop 1 x tabletop cushion
1 x le & right half of the seat
(low / high)
1 x small seat frame 1 x backrest
(low / high)

4 inhoud
4 x bolt M8 x 70
1 x plastic spacer 1 x cap 50 x 50 1 x cap 60 x 60
1 x shade frame with fabric 1 x vertical shade pole
KOSMOS SHQDE
OPTION

english 5
3 x bolt M6x25 8 x bolt M6x12
1 x tabletop 1 x tube 1 x base plate
VRIJSTAANDE TAFEL
OPTION

+/- 45 min.
6 montage kosmos
Now unscrew the leveling feet that are not touching the
ground surface from above with a at screwdriver and
further ensure that the whole is level.
3. Place the backrest between the two seat halves and six
M6x14 bolts and cap nuts. M6. Now tighten all the
bolts.
in case you bought a xed table, rst mount the
aluminium prole to the small seat frame and the
tabletop connection on top of it, with M6*30mm bolts.
2. Now connect the two halves of the seat to the small
seat frame using three bolts M6x80 and three M8 nuts.
Attention: do not tighten them yet. Do not tighten
them yet.
1. First mount the table leg to the small seat frame with 4
bolts M6x30. Now remove the transport screw.
2 people
screwdriver
ASSEMBLY KOSMOS
UTILITIES

sitting lounging
english 7
To use the table again, you need to hold down the lever under the table top while pulling the table up with the other
hand.
To turn the table into a sofa bed, press the table down with your right hand while pressing the lever under the table
top with your left.
HOW DOES THE ADJUSTABLE TABLE WORK
4. Screw the table top down with the countersunk screws
M6x2. e control element for the height adjustment is
fastened with 4 bolts M4x10 at the bottom of the table
top. is control element must point towards the seat
opening
5. Now place the cushions in the Kosmos.

+/- 45 min.
sitting lounging
e two free openings are used to tilt the parasol
slightly backwards in order to level the parasol cloth,
by means of adjusting screws.
To do this, rst unscrew the top bolts again a little looser
until the ideal angle is reached, and then turn the set
screws clockwise until against the vertical tube.Use a #4
Allen wrench to do this.
5. From the inside of the furniture, insert 4 bolts M8x70
through the holes provided (two at the bottom and two
at the top). at the bottom and two at the top).
On the outside, then slide the plastic spacer Erover and
then the parasol pole. Tighten rmly.
Follow the rst 4 steps from pages 4-5.
ASSEMBLY WITH KOSMOS SHADE
UTILITIES
2 people
screwdriver
8

sitting lounging
8. Install the appropriate caps on the parasol frame and
the vertical tube. Now place the cushions in the Kosmos
as in step 5 on page 5.
10. Now open the parasol. Does the magnetic lock not
hold, rst loosen the velcro strap and open the parasol
again. Only now you can close the velcro again. In closed
position one has to x the leather leather strap on the
umbrella frame to be attached to the two to the two
outer ribs to prevent the parasol from the parasol from
opening.
6. Take the parasol frame with cloth and go with the cord
as close as possible to the end of the parasol pole. Lower
the cord through the opening until it emerges at the
bottom. Aer assembly, a certied electrician to t the
end of the cable with a suitable plug. with an appropriate
plug.
7. Now insert the parasol through the opening in the
vertical tube until it locks in place and lock in place with
bolts M6x12.
english 9
This strap can also be used to hold the parasol open:
a) In case of rain: creates drains.
b) After not using the parasol for a long time: it is possible
that the magnetic clasp does not hold temporarily, due
to internal tension in the parasol fabric. If this is the
case, please place the strap on the magnetic ribs as
long as necessary in order to stretch the fabric again.
Optional: screw the lamp into its socket.

10
5. Make sure the screw is not fully extended. 6. Reassemble the lever using the screws you just
removed. you have just unscrewed. If still not sucient,
repeat steps 1 - 3.
3. Check for any slack between the cable & mounting
screw.
4. If so, turn the screw out until the play is gone & turn
then continue for an additional 2 revolutions.
1. Disassemble the valve by unscrewing the screws and
turn the valve over.
ADJUSTING ADJUSTABLE TABLE

pull to untie
english 11
4. At the back of the Kosmos, tie the string attached,
under the parasol pole. It is best to do this as described
here.
5. Close at the front the velcro fasteners and the snap
closure.
1. Make sure the cushions are nice and upright, and put
the table to the highest position. Place the seat cover
over the the Kosmos with the pie-shaped opening in the
entrance of the seating unit. e table comes out above
the cover, and the table leg sits in the tip of the pie piece.
2. Pull the side ap all the way up to the bottom of the
of the furniture. Position the corner seams of the cover
nicely on top of the corner piece.
SEAT COVER
1. Slide the parasol cover over the closed parasol. If your
parasol includes lighting, care should be taken to avoid
breaking the lamp. break.
2. Close the zipper.
SHADE COVER
COVERS
TABLETOP COVER

12
5. Insert the new LED, slide the nut over the cord, and
tighten the nut. Insert the cable through the tube so that
it emerges at the other end.
6. Connect the wires to the LED adapter as shown here
shown.
7. Replace both caps on the ends of the parasol tube.
3. Remove the tube cap in the center of the parasol, pull
the cord through the tube and unscrew the nut from the
lighting base.
4. Remove the broken LED from the tube and twist the
bulb o so that it can be attached to the new LED bulb.
on the new LED bulb. Do not forget to place the rubber
ring to place it.
1. Remove the tube cap with switch and remove the LED
adapter from the parasol tube.
2. Remove the red and black cables from the adapter.
BULB REPLACEMENT

english 13
MAINTENANCE
CUSHIONS
Easily cleaned with warm water
and a microber cloth. Do not
use solvents, bleaches, abrasives,
chemical detergents or waxes.
For outdoor use, the optional
cover should be placed over the
entire furniture when not in use,
as the cushions are not 100%
waterproof for ventilation reasons.
e cushions should be cleaned
regularly to preserve their
appearance and to prevent the
formation of dirt and bacteria.
Lacquers and inks,
cleaning products,
detergents and solvents such as
thinner, acetone or alcohol can be
very eective in removing stains,
but cause direct damage and
contribute to the deterioration
of the material. e use of such
cleaning agents is at your own risk
TABLETOP
HPL (high presure laminate): can
be cleaned with standard cleaners
as one uses for the kitchen. For
stubborn stains we use “HG plastic,
paint and wallpaper intensive
cleaner”. For more info: www.
hginternational.com
WARNING
Never sit on the backrest to avoid
damage to the cushions and
aluminum plate.
SHADE
Clean the parasol fabric and cover
by rinsing with water and hand
soap, and gently rubbing with a
so brush. Initially, make sure
the parasol fabric does not get
too dirty and place the cover over
the parasol as much as possible.
Never spray the parasol
with a high pressure cleaner.
Brush very gently, be extra careful
on the seams, they can come
loose with too hard friction.
Aer cleaning, the fabric has to be
dried completely in open position.
Do not use detergents.
ese will damage the
protective layer of the textile.
For stubborn stains, we recommend
“awning, tarpaulin and tents
refresher’ of the brand ‘HG’. See
www.hg.eu for more info. Follow
strictly the instructions on the bottle
Translated with www.DeepL.com/
Translator (free version)!
WARNINGS
In case of strong winds or non-use,
close the parasol and apply the cover
to prevent the parasol from blowing
open or becoming dirty.
Never leave the opened parasol
unattended.
Do not leave the Kosmos parasol
closed if it is not completely dry. Do
not leave it closed for long periods in
humid conditions.
If you do not use the parasol for
a long time, store it as follows:
perfectly dry in a dry environment.

1. Take the base plate and mount it by means of 3
countersunk hexagonal bolts M10 x 25 on the underside of
the the stainless steel tube as shown in the drawing.
2. Now place the table top on the stainless steel tube as
indicated in the on the stainless steel tube as shown in
the drawing and attach it using 8 hexagon bolts M6 x 12.
ASSEMBLY FREESTANDING TABLE
14

english 15

16 inhoud
content p. 3
assembly kosmos p. 6
assembly with kosmos shade p. 8
adjusting adjustable table p. 10
covers p. 11
bulb replacement p. 12
onderhoud p. 13
assembly freestanding table p. 14
inhoud p. 17
montage kosmos p. 20
montage met kosmos shade p. 22
bijregelen verstelbare kabel p. 24
montage hoezen p. 25
lamp vervangen p. 26
onderhoud p. 27
monatage vrijstaande tafel p. 28

nederlands 17
INHOUD
1 x linkse en rechtse zetelhel
(laag of hoog)
1 x zetelframe klein 1 x rugsteun
(laag of hoog)
1 x verstelbare tafelpoot
of vaste tafelpoot
1 x tafelblad 1 x tafelkussen
2 x groot zitkussen 1 x klein zitkussen 4 x groot rugkussen
(laag of hoog)
3 x klein rugkussen
(laag of hoog)
6 x vijs M8x80 6 x moer M8
6 x vijs M6x14 6 x dopmoer M6 5 x vijs M4x10 8 x vijs M6x12
4 x vijs M6x30 ???

1 x parasolframe met doek 1 x parasolpaal
4 x bout M8 x 70
KOSMOS PARASOL
OPTIONEEL
18 inhoud
1 x plastic plaat 1 x dop 50 x 50 1 x dop 60 x 60

1 x tafelblad 1 x buis 1 x voetplaat
VRIJSTAANDE TAFEL
OPTIONEEL
nederlands 19
3 x verzonken binnenzekantbout M6x25 8 x binnenzeskantbout M6x12

MONTAGE KOSMOS
BENODIGDHEDEN
extremis sleutel
2 personen
philips schroevendraaier
1. Monteer eerst de tafelpoot op het kleine zetelframe
met 4 bouten M6x30. Verwijder nu de
transportschroef.
+/- 45 min.
In geval van vaste tafelpoot: monteer eerst de lange
rechthoekige buis op het kleine zetelframe en de
tafelbladconnectie er bovenop, met bijgeleverde bouten
M6 x 30.
2. Koppel nu de beide zetelhelen aan het kleine
zetelframe met behulp van telkens drie bouten
M6x80 en drie moeren M8. Opgelet: span deze nog
niet aan.
Draai nu de stelvoetjes die het grondoppervlak niet
raken van bovenaf met een platte schroevendraaier uit
en zorg verder dat het geheel waterpas komt te staan.
3. Plaats de rugsteun tussen de twee zetelhelen en
schroef dit vast met zes bouten M6x14 en dopmoeren
M6. Span nu alle bouten aan.
20 montage kosmos