EZee Life 180-24 User manual

EZee Life™ Products
34 Futurity Gate, Unit 15
Concord, Ontario L4K 1S6
22” & 24” Quick Release
Wheels
Assembly Instructions
…...............................................

2
1) Attach the triangular axle brackets to the lower back
posts of the commode with the extended portion of the
axle tube extending to the outside of the commode and
the axle tube to the back of the back tube (see Fig. 1).
Tools needed: 4mm allen key & 10mm wrench.

3
The bevel edge of triangle bracket is the top.
2) After triangle bracket assembly, press the button on the
axle end to release the locking ball bearings and insert
the axle through the wheel from hand rim side of the
wheel. (see Fig. 2)

4
3) Once the axle is fully inserted through the wheel,
align the axle end with the opening in the axle tube
on the triangle bracket and slide the axle through it.
Note that the lock release button must always be
depressed while inserting and removing the axle.
4) Ensure the axle is inserted properly with ball
bearings fully through the bracket. Please note the
clearance between the ball bearing and the surface
of the bracket must not exceed 0.3 mm.

5
5) If over 0.3 mm, the distance between the axle and the
plunger must be adjusted (see Fig. 5). Holding the axle at the
bearing end with an 11 mm open end wrench, tighten the
adjustment nut at the button end of the axle using a 19 mm
socket.
6) After adjusting the axle thread should be visible beyond the
nut.

6
7) There are three wheel heights on the back frame as
seen in the image below (see Fig. 7). Ensure both the
rear wheel height and caster height are set to the
same positions.
Rear Axle Settings
Matching Caster Settings

7
Brake Installation
Wheel locks must be installed with the large wheel installation
as the caster brakes are removed with the rear casters.
1) Attach the large opening of
the brake clamp to the seat
rail loosely.
2) Slide in the brake mounting
bar to small side of the brake
clamp and continue to tighten
until it is just snuggly
attached.
3) Position while assembly
so that the locking bar is
in front of the commode
tire.
4) Tighten clamp fully
and apply the brake. It
should press in to the
tire between 1/8” and
¼” when adjusted
properly. Check to ensure
the wheel won’t spin
when the brake is applied.
5) Repeat for wheel on
opposite side of the
commode.
If the wheels begin slipping at
any time when the brakes are
applied loosen the brake clamp
slightly and slide the brake
assembly closer to the wheel
and retighten

8
For video instructions please visit:
https://youtu.be/VTYaE7jdzOU
To See all the Aluminum Commode Instruction Videos please
visit:
http://www.healthlinemedical.com/instructions.php
Warranty:
EZee Life™ products carry a one-year warranty against manufacturing
defects, faulty materials and workmanship.
In the event of a defect covered by this warranty, we will, at our option,
repair or replace the item. Please contact your supplier/dealer for assistance
should a defect become apparent.
The warranty does not extend to consequential costs resulting from the fault
or defect in the product, in particular freight and travel costs, loss of
earnings, expenses or other expenses which may occur.
The warranty does not cover normal wear and tear resulting from normal
use or damage caused by accident, misuse, negligence or improper
installation or assembly.
The vendor/manufacturer will not accept responsibility for any damages or
injury caused by misuse, negligence or non-observance of the instructions
supplied.
Imported & Distributed by:
Healthline Medical Products
1065 E Story Rd. Winter Garden, Fl 34787
Toll-Free: 1-800-987-3577 Fax: [phone]
Email: [email protected]