Faber Relaxed Premium M User manual

Relaxed Premium M



40010959‐1440RelaxedPremiumMENG

InstallationInstructions
1 < <<<
3 alternative finishes.
1.1a
1.1b
1.1c

InstallationInstructions
2 < <<<
1.2


1.3

1.4
7

InstallationInstructions
3 < <<<


1.9
1.5
1.6
B

InstallationInstructions
4 < <<<
2.1 2.2
2.3
3.1 3.2
3.3 3.4


InstallationInstructions
5 < <<<




3.5
4.1
4.2
4.3

InstallationInstructions
6 < <<<
1Dearuser
CongratulationsonpurchasingyourFaberproduct!
Aqualityproduct,whichprovideyouwiththe
warmthandatmosphereformanyyears.Please
readtheusermanualbeforeusingthefire.Should,
despitethecarefulfinalchecks,amalfunction
occur,pleasecontactyourFaberdealer.

Pleasenote:
Thedataofyourfireisavailableinthe
usermanual.
1.1 Introduction
Onlyhavetheapplianceinstalledbyaqualified
installeraccordingtothegassafetyregulations.
Readthisinstallationmanualproperly.
1.2 Pleasecheck
Checkthefirefortransportdamageandreportany
damageimmediatelytoyourdealer.
1.3 CEDeclaration
GlenDimplexBeneluxcertifiesthatthisFaberfire
complieswiththeessentialrequirementsofthe
gasappliancesdirective.
Product:gasroomheater
Model:RelaxedPremiumL
ApplicableECdirectives:90/396/EEC
Harmonisedstandardsapplied:NEN‐EN‐613
NEN‐EN‐613/A1

ThisDeclarationisinvalid,ifwithoutthewritten
permissionofGlenDimplexBenelux:
Changesaremadetotheappliance.
Thefireisconnectedtootherexhaust
materialsthanspecified.
2Safetyinstructions
Theunitmustbeinstalledandchecked
everyyearaccordingtotheseinstructions
andtheapplicablenationalandlocal
regulations.
Ensurethatthedataonthetypelabel
matchesthelocalgastypeandpressure.
Thesettingsandtheconstructionofthe
firemustnotbechanged!
Donotplaceextraimitationwoodor
othersmoulderingmaterialontheburner
orinthecombustionchamber.
Theunitisforatmosphereandheating
purposes.Thismeansthatallsurfaces,
includingtheglass,canbeveryhot(over
100°C);exceptionstothisarethebottom
ofthefireandthecontrolelements.
Donotplaceanycombustiblematerials
within0.5moftheradiationareaofthe
fire.
Lightthefireforthefirsttimeandrunfor
severalhoursonthehighestsetting,so
thatthepaintcancure.Provideadequate
ventilation,sothatanyfumescan
disperse;werecommendvacatingthe
roomduringthisprocess
Pleasenote
Throughthenaturalaircirculationofthe
firemoistureanduncuredvolatile
componentsfrompaint,building
materialsandcarpetedfloors,etc.are
attracted.Thesepartscansettleassoot
oncoldsurfaces.Thereforedonotlight
thefireshortlyafterinstallation.
3Installationrequirements
3.1 Fire
Thisdevicecanbebuiltintoanexistingor
newchimney.
Fordeviceswithflexiblegaspipesthegas
regulatorblockismountedontheright
sideofthefirefortransportreason.
Thegasregulatorblockwiththereceiver
andtheI.T.C.mustbeplaceddirectly
behindaservicedoor.(seeFig.3.1)
3.2 Falsechimneybreastorother
structure
TheFalsechimneyshouldbeofnon‐
combustiblematerial.
Thespaceabovethefireshouldalwaysbe
ventilatedusingthesuppliedgridsora
similaralternativewithminimalfree
passageof200cm²pergrid.
3.3 Fluepipeandterminalrequirements
Forthesupplyofthecombustionairand
thedischargeofthecombustiongases
youshouldalwaysusetheFluematerials
specifiedbyFaber.
Pleasenote:
Onlywhenusingthesematerialscan
Faberguaranteethesafeandproper
operationoftheappliance.
Theoutsideoftheconcentricfluematerial
canheatupto+/‐150°C.Ensure,when
penetratingaflammablewallorceiling,

InstallationInstructions
7 < <<<
constructionwithproperinsulationand
protection.Andensurerespective
distance.
Ensureforgreatdischargelengthsthat
theconcentricdischargematerialis
supportedeverymeter,sothattheweight
ofthematerialisnotsupportedbythe
fire.
Itisnotpermittedtostartdirectlyonthe
devicewithconcentriccutdownpipe
material.
Theairsupplycouldthenpossiblybe
closed.
3.4 Terminals
Thecombinedsupplyanddischargecanbedone
bothviawallorthroughtherooforthroughan
existingchimney.
Pleasenote:
Verifyifthepositionoftheterminalmeetsthe
localregulationsregardingventilationopenings.
Forproperfunctioning,theairsupplyand
combustiongasdischargearenottobe
obstructed.Theminimumdistancesarespecified
inChapter15.
3.4.1 C11,Wallterminal.
Forafacadeorwalloutletuseawallterminal.(see
Fig.3.5C11)
Dependingonthecalculationthiscanbea
diameterof130/200mmor100/150mm.
3.4.2 C31,Roofterminal.
Foraflatorpitsroofoutletusealongroofoutlet
withadiameterof100/150mm(seeFig.3.5C31)
3.4.3 C91,Existingchimney.
Foranexistingchimneyusetheshortchimney
outletwithadiameterof100/150mm(seeFig.3.5
C91).

Inthiscasetheexistingchimneyactsasairinletan
insertedflexiblestainlesssteelpipedischargesthe
fluegas.Thetopandthebottomshouldbe
airtight.
Dependingonthecalculatedoutletdiameter,usea
flexiblestainlesssteeltubeofØ100mmorØ
130mmwithCEmarkingfor600°C.
Pleasenote:
Theminimumchimneydiameterfora130mm
flexiblestainlesssteelpipemust200x200mm.
Andfora100mmflexiblestainlesssteelpipe
150x150mm.
4Preparationandinstallation
instructions
4.1 Gasconnection
Thegasconnectionmustcomplywiththe
applicablelocalstandards.
WeadviseusingaØ15mmgasconnectiondirectly
fromthegasmetertotheappliance,withashut‐
offvalveintheproximityoftheappliance,which
mustalwaysbefreelyaccessible.
Positionthegasconnectionsothatitiseasily
accessibleatalltimesforservice,andthatthe
burnerunitcanbedisassembled.
4.2 Electricalconnection
Thepowersupplymustcomplywiththeapplicable
localstandards.
A6Voltadapterisused.
Forthis,awallsocket230VAC/50Hzmustbe
installednearthefire.
4.3 Preparingthefire
Removethefirefromitspackaging.
Ensurethatthegassupplypipesunder
theappliancearenotdamaged.
Removeframeandglassandtakethe
packagedpartsfromthefire.
Storeframeandglassinasafeplace.
Preparethegasconnectiononthe
regulator
4.4 Positioningthefire
Taketheinstallationrequirementsintoaccount
(seeChapter3).
Placetheunitintherightpositionandsetthe
heightwiththeleglevellers.
Heightadjustmentandlevellingofthefire(seeFig.
1.9B).
Roughheightadjustment:
withtheextendableleg,orwiththelong
legssupplied.
Fineadjustment:
withtheadjustablefeet.
4.5 InstallingtheFluematerials
Whenpenetratingawallorceilingthe
openingmustbeatleast5mmlargerthan
thediameterofthedischargematerial.
Horizontalsectionsshouldbeinstalled
withaslopetowardsthefire(3degrees).

InstallationInstructions
8 < <<<
Buildthesystemfromthefire.Ifthisis
notpossibleyoucanmakeuseofan
extendableadaptersection.
Fortruinguptheexhaustsystemusethe
½meterpipe,whichcanbeshortenedand
ensurethattheinnerpipeisalways2cm
longerthantheouterpipe.
Parts,whichareshortened,mustbe
securedwithaself‐tappingscrew
Wallandroofterminalscanalsobecut.
Donotinsulatebutventilatebuilt‐influe
material.(approx.100cm2).
4.6 Constructingthefalsechimney
Ifpossible,carryoutaperformancetestatthefire
beforefinallyfinishingtheinstallation.

4.6.1 Minimumfalsechimneysizeand
distancetocombustiblematerials
Constructthefalsechimneyofnon‐combustible
materialincombinationwithmetalprofilesorof
masonry/concreteblocks.
Alwaysusealintelorreinforcingbarswhile
brickingtheoutlet.Theyshouldnotbeplaced
directlyonthefire.
4.6.2 Ventilation
Theventilationmustcomplywiththeapplicable
localstandards.
Correctventilationpreventsatoohigh
temperatureofthegasregulatorblockandits
electronicsandalsolimitsthetemperatureofthe
convectionair.Thereforeplanforoutletofgrills
andaventilatingcontrolhatchwithaminimum
freepassageof200cm2pergridorasimilar
alternative.
Placeabovethegratesascreenplatemadeofnon‐
combustiblematerial.(seeFig.1.9A)
4.6.3 Installationandfinishing
Forinstallationandfinishingthefollowingpoints
areofinterest:

A=Fixingpoints(Fig.1.2).
B=Mouldings(Fig.1.2).
C=Spacer(Fig.1.2)

D,FandH(Fig.1.3).

Pleasenote:
Ensurethatthefireisnotload‐bearingwithregard
tothefalsechimneybreast.
(SeethedimensionaldrawingChapter18.1).

Payspecialattentiontothefollowingpoints:
1. Checkduringworkiftheglasscanbe
insertedandremoved.
2. CheckduringworkifthemouldingsB
(Fig.1.2)orQ(Fig.1.5)match.
4.6.4 Method1(Fig.1.1a)
Buildthefalsechimneybreastagainstthefixing
pointsA(Fig.1.2).Theinstallationmustalwaysfor
installingandremovingtheglass!

Takeintoaccountthethicknessofthefinish!

SpacerCisinlinewiththetopoftheglassslotH
(lineF)(Fig.1.3).

DonotusespacerCasasupportingstructure.

Removethefixingpoints(A)onthesidewall
beforetheoutletwallisfinallyfinished!(Fig.1.4).
4.6.5 Method2(Fig.1.1b)
ProcessseeChapter4.6.3
4.6.6 Method3(Fig.1.1c)
RemovethespacerC(Fig.1.5).Toensuretheair‐
tightnessoftheunitthescrewsmustbereplaced.

ThebaseX(Fig.1.5)mustbe2mmclearofthe
spacerR(Fig.1.5)and4mmabovetheglassslotH
oftheunit(Fig.1.5).ThiswillallowthemouldingQ
(Fig.1.5)tobeonthesamelevelasthebase.
4.6.7 Mountingthemouldings.
First,placethebottommoulding.
Thenplacetheleftandrightmouldings
(thesearefixedbytheadjustable
magneticsnappers)
Attachtheuppermouldingandsecureit
withthe3Torxscrews.
(SeeFig.1.2B)

Removethebottommouldingsusingthesupplied
magneticknob(Fig.1.8).
5Removingtheglass
Removethemouldings,seeChapter4.6.6
Placethesuctioncupsontheglass.
Drawthesealingcordfromtheslot.
(Fig.2.1).
Slidetheglasstothetopsothatthe
bottomisreleasedfromtheslot.Nowpull
theglassoutandgraduallydown.
(Fig.2.3).

InstallationInstructions
9 < <<<
6Placingthedecorationmaterial
Itisnotpermittedtouseotherortoaddmore
materialinthecombustionchamber.
Keepthepilotlightalwaysfreeofdecoration
material!
Donotplacealldecorationmaterialatonetimeon
theburner;thefabricpartscanblockit.
6.1 Logset
Placesomeofthechipsontheburnerand
onthebottom.
Placethelogsasspecified.(seeFig.(4.1of
includedlogsetcard)
Dividetherestofthechipsontheburner
andonthebottom.Preventathicklayer
ontheburner;thisadverselyaffectsthe
fireimage.
6.2 Glowwire
The“glowwire”givesadecorativegloweffect.

Pullthewoolwellapartandplaceindifferent
placestuftsontheburner.

Pleasenote:
Donotusetheglowwirenearthepilot
flame!
Thiscancauseashortcircuitintheignitionsystem!

6.3 Pebbles
Placethepebblesontheburnerandon
thebottom.(seeFig.4.2and4.3of
includedwoodsetcard).Preventadouble
layer;thisadverselyaffectsthefireimage.
Replacetheglassandcheckthefire
image.

Startthefireasdescribedintheusermanual.
Checkiftheflamedistributionisgood.Movethe
chipsifnecessary,untilagoodflamedistributionis
achieved.
7Checkingtheinstallation
7.1 Checkingthemainburnerignition,
pilotflame
Ignitethefireasdescribedintheusermanual.
Checkthatthepilotflameiswellabove
themainburnerandnotcoveredbychips.
Checktheignitionofthemainburneron
fullandsmallsetting.(ignitionmustbe
smoothandquiet).
7.2 Checkingforgasleaks
Checkwithagasleakfinderorsprayall
connectionsandpipesforgasleakage.
7.3 Checkingtheburnerpressureand
primarypressure
Checkthattheburnerpressureandprimary
pressurematchtheinformationlistedinthe
manual,Chapter14Technicalspecifications.

Measuringtheprimarypressure:
Closetheshutoffvalve.
TurnmeasuringnippleB(seeFig.3.2)
someturnsopenandconnectameasuring
hosetothegasregulator.
Takethismeasurementathighestsetting
ofthefireandwhenthefireissettopilot
light.
Donotconnecttheunitifthepressureis
toohigh.

Measuringtheburnerpressure:
Checktheburnerpressureonlywith
properprimarypressure.
TurnmeasuringnippleA(seeFig.3.2)
someturnsopenandconnectameasuring
hosetothegasregulator.
Thepressuremustcorrespondtothe
valueindicatedinthetechnical
specificationsofthismanual.Incaseof
deviationcontactthemanufacturer.
Pleasenote:
Closeallpressuremeasuringnipplesand
checkforgasleakage.
7.4 Checkingtheflameimage
Letthefireburnforatleast20minutesathighest
settingandchecktheflamefor:
1. Flamedistribution
2. Colouroftheflames

Ifoneorbothpointsarenotacceptablethen
check:
Thelogsetlayoutand/ortheamountof
chipsontheburner.
Thepipeconnectionsforleaks(incaseof
blueflames).
WhetherthecorrectRestrictorisfitted.
Theoutlet.
oWallterminalrightsideup
oRoofterminalontheright
position
oIfthemaximumhorizontalflue
lengthsisnotexceeded.