Fagor HAN 8000 User manual

HAN 8000
4 x HDMI to ASI / IP Encoder

TABLE OF CONTENTS

Contenido
1 SAFETY INSTRUCTION .............................................................................................................................. 1
2 OVERVIEW. .............................................................................................................................................. 2
3 SYSTEM PRINCIPLE .................................................................................................................................. 3
3.1
SYSTEM DIAGRAM ............................................................................................................................... 3
3.1.1 HDMI ........................................................................................................................................... 4
3.1.2 A V Encoding................................................................................................................................ 4
3.1.3 TS Process.................................................................................................................................... 4
3.1.4 Data output port .......................................................................................................................... 4
4 SPECIFICATIONS....................................................................................................................................... 5
4.1
HDMI. .................................................................................................................................................. 5
4.2
H.264 Video Compression .................................................................................................................... 5
4.2.1 Video. .......................................................................................................................................... 5
4.2.2 Audio ........................................................................................................................................... 6
4.2.3 Format. ........................................................................................................................................ 6
4.3
DATA PORT. .......................................................................................................................................... 6
4.3.1 DVB ASI ....................................................................................................................................... 6
4.4
CONNECTIONS ..................................................................................................................................... 6
4.4.1 Input ........................................................................................................................................... 6
4.4.2 Video Format ............................................................................................................................... 6
5 EQUIPMENT CONNECTION. ..................................................................................................................... 7
5.1
FRONT PANEL DISPLAY AND KEY BUTTON ............................................................................................. 7
5.2
REAR PANEL ......................................................................................................................................... 7
6 INSTALLATION GUIDE. ...................................................................................................................... 8
6.1
INSTALLATION PREPARATION. ............................................................................................................... 8
6.2
ENVIRONMENT ENQUIRIES. ................................................................................................................. 8
6.3
GROUNDING REQUIREMENTS. ............................................................................................................. 8
6.3.1 Rack grounding. ........................................................................................................................... 9
6.3.2 Equipment grounding. ................................................................................................................. 9

7 BASIC PROGRAMMING GUIDE................................................................................................................10
7.1
KEYBOARD + LCD. ................................................................................................................................10
7.1.1 Lock Status display ......................................................................................................................10
7.1.2 Main menu display .....................................................................................................................10
7.1.3 Encoder Setting. .........................................................................................................................10
7.1.4 Programming of the rest of encoders. .........................................................................................14
7.1.5 ASI ..............................................................................................................................................14
7.1.6 Output Setting ............................................................................................................................14
7.1.7 IP Output ....................................................................................................................................15
7.1.8 Network Setting ..........................................................................................................................19
7.1.9 Save Config .................................................................................................................................20
7.1.10 Load Config .................................................................................................................................20
7.1.11 Version .......................................................................................................................................20
7.1.12 Language ....................................................................................................................................20
7.1.13 Error Info. ...................................................................................................................................21
7.1.14 Error Info and Shooting ...............................................................................................................21
7.1.15 Indication Status .........................................................................................................................21
8 NMS OPERATION GUIDE .........................................................................................................................22
8.1
NMS LOGIN .........................................................................................................................................22
8.2
ADD FREQUENCY ................................................................................................................................24
8.3
ADD DEVICE ........................................................................................................................................24
8.4
EDIT DEVICE ........................................................................................................................................25
8.5
CHECK AND SET CONFIGURATION ........................................................................................................28
8.5.1 Output Setting ............................................................................................................................29
8.5.2 Audio and Video Config...............................................................................................................30
8.5.3 ASI ..............................................................................................................................................31
8.5.4 PID Passthrough ..........................................................................................................................32
8.5.5 Edit NIT .......................................................................................................................................33
8.5.6 IP Output ....................................................................................................................................34
8.6
PUBLIC FUNCTION OF NMS .................................................................................................................35

1
1 SAFETY INSTRUCTION
 Read this manual carefully before use.
 Do not open the case without disconnecting it from the mains
 Allows the air circulation around the equipment
 Protects against the water or liquids drops on the equipment
 Do not place near to the heat sources or hot areas.
 It is required a room with good ventilation.
 Do not obstruct he ventilation slots.

2
2 OVERVIEW.
The HAN 8000 encoder modulates the content of 4 HDMI input (MPEG-4 AVC/H.264 HD) signals to a
DVB-ASI or IP output. It supports 1080i/p and 720p. The housing of this equipment is adapted to the 19”
rack with 1 unit height.

3
TS Processing
3 SYSTEM PRINCIPLE
3.1 SYSTEM DIAGRAM
HDMI in 1 HD A/D Encoding
HDMI in 2 HD A/D Encoding ASI Output
HDMI in 3 HD A/D Encoding IP/UDP out
HDMI in 3 HD A/D Encoding
ASI input
CPU

4
3.1.1 HDMI
As it is showed in the above diagram the HDMI input signals are sent to the encoding module.
3.1.2 A V Encoding
Video coding adopts H.264 real time compression encode chip to encode the digitalized video data
from video port and then output video ES (Elementary Stream) which will be sent to video packetizer.
And the PES (Packetized Elementary Stream) generates and it will do audio and video stream processing.
During the process of compression encoding, it uses MPEG2 MP@ML and the max bitrate can reach to
15Mbps. Audio Coding uses professional audio coding software to encode the analog audio signal from
audio port by adopting MPEG1 Layer 2 standard. The encoded audio Elementary Stream will be sent to
audio packetizer. And the audio PES will do audio and video stream processing.
3.1.3 TS Process
TS process composites 4 channels ES stream to output one standard MPEG2 TS stream.
3.1.4 Data output port
Processed TS will be sent out through the port. It conforms to DVB ASI standard and
supportsUDP@RJ45.

5
4 SPECIFICATIONS
Input 4×HDMI High Definition Multimedia Interface
ASI DVB standard, BNC interface
Video Coding
4:2:0 encoding H.264 HP@L4 MP@L3
H.264 Adaptive Field Frame (AFF)
H.264 Field-Based (FB)
full HD: 1920×1080×60/50i/p, 1280×720×60p/50p
Standard ISO/IEC14496-10 (H.264/MPEG-4 AVC)
Audio
Bit rate 128, 160, 192, 224, 256, 320, 384Kbps
Property MPEG-1 Layer2
Sample Bit rate 32KHz, 44.1KHz, 48KHz
Output 2×ASI DVB standard, BNC interface
IP IP/UDP (TS over IP), MPTS/Unicast/Multicast
Output Bit rate 1 to 20Mbps (4:2:0) per channel
Control NMS (Ethernet port, RJ-45), Keyboard + LCD
General
Features
Size 482mm×410mm×44mm
Temperature
Range 0~45°C (Operation); -20~80°C (Storage)
Power 100-240VAC, 50Hz, 25W
4.1 HDMI.
Connector HDMI. Supports max 1920x108 50i.
4.2 H.264 Video Compression
4.2.1 Video.
Output bit rate: 1-20 Mbps per channel.

6
4.2.2 Audio
MPEG-1 Layer 1/2
4.2.3 Format.
DVB Transport Stream.
4.3 DATA PORT.
DVB ASI; IEEE802.3 Ethernet, RJ45
4.3.1 DVB ASI
Standard: DVB ASI
Connectors: BNC
Impedance: 75 Ohm
Package format: 188 bytes
4.4 CONNECTIONS
4.4.1 Input
4 x HDMI inputs, and one ASI input.
4.4.2 Video Format
High definition: 1920*1080i/p *50/60; 1280*720p*50/60.

7
5 EQUIPMENT CONNECTION.
5.1 FRONT PANEL DISPLAY AND KEY BUTTON
 1: LCD
 2: ASI active input indicator LED.
 3: HDMI input active indicator LED.
 4: Error indicator LED.
 5: Power indicator LED.
 6: Keyboard. LEFT, RIGHT: move the cursor / UP, DOWN: change parameters.
 7: Enter key. Confirm and operate
 8: Exit key. Back to upper menu or cancel the setting.
NOTE: To unlock the device press ENTER and EXIT. Keyboard auto-lock is activated after 60 seconds
without operation.
5.2 REAR PANEL
 1: HDMI inputs.
 2: ASI input (BNC).
 3: ASI outputs (BNC).
 4: TS over IP output, (RJ 45).
 5: Ethernet connection for control (RJ-45).
 6: Power Switch.

8
6 INSTALLATION GUIDE.
6.1 INSTALLATION PREPARATION.
 Before installation check possible lose or damage of the device during transportation and read
the complete user manual.
 Prepare a suitable environment for installation
 Install the device.
 Connect the signal cables.
6.2 ENVIRONMENT ENQUIRIES.
 It is recommended to take into account the following point related with the installation
environment:
 When installing multi-row of racks, please make the distance 1.2~1.5M between front
door and back door, and the distance 0.8M between rack and wall.
 The floor of the room where is installed the device should be non-conducting, dust free.
Anti-static material volume resistivity: 1x107 ÷ 1x1010 Ω, ground current-limiting
resistance: 1MΩ, floor bearing weight: > 450Kg/m2.
 Working temperature: for long term operation: 5 ÷ 40º C, for short term operation: 0 ÷ 45º.
 Relative humidity: for long term operation: 20% ÷80 %, for short term operation: 10% ÷ 90%.
6.3 GROUNDING REQUIREMENTS.
Good ground wire design is the base of the whole system, and is essential to lightning protection and
anti-interference. The system must follow above principles:
 Keep good electrical contact between both ends of outer conductor and shielding layer and the
appearance of metal case of the connected device.
 Make sure that connections of both ends of the ground wire are with good electrical contact
and prepare for corrosion prevention treatment.
 Do not use other device for ground wire electrical connection.
 The sectional area of ground wire from rack connecting to anti-thunder unit must be greater
than or equal to 25mm2

9
6.3.1 Rack grounding.
Ground terminals of racks in one room should be separately connected to protective are copper bar
provided by side board. And ground wire should be as far as possible short. If the wire is too long when
installing, please cut off to avoid ground wire coiling. The sectional area of guide line of ground
terminal row must be greater than or equal to 25mm2.
6.3.2 Equipment grounding.
When grounding, use guide line to connect protective area binding post to the protective ground wire
row of assembly rack.

10
7 BASIC PROGRAMMING GUIDE.
7.1 KEYBOARD + LCD.
7.1.1 Lock Status display
7.1.2 Main menu display
After initialization, the menu shows as below (Press ‘up or down’ key to choose menu, then press
the ‘enter’ key to confirm):
7.1.3 Encoder Setting.
Encoder1, Encoder2, Encoder3 and Encoder 4 are programmed in the same way. Below taking
encoder1 as an example: use Up and Down keys to choose encoder1 and then it shows as
below (Press ‘up or down’ key to choose menu, then press the ‘enter’ key to confirm):
4IN1 HD HDMI Encoder
PG: 04 Bitrate:
3
0.000Mbps
1. Encoder 1
2. Encoder 2
3. Encoder 3
4. Encoder 4
5. ASI
6. Output
Setting
7. IP Output
8. Network
Setting

11
7.1.3.1 Video Format
7.1.3.2 System BitRate
For the system bit rate, the Factory Default is of 8Mbps:
1.1. Video Format
1.2. System BitRate
1.3. CBR-VBR
1.4. Video Profile
1.5. Video Level
1.6. Audio BitRate
1.7. PMT PID
1.8. VIDEO PID
1.9. AUDIO PID
1.10. PCR PID
1.11. Prog. Name
1.12.
Provider
1.1. Video Format
AUTO
1920*1080*60p
1920*1080*59.94p
1920*1080*50p
1920*1080*60i
1920*1080*59.94i
1920*1080*50i
1280*720*60p
1280*720*59.94p
1280*720*50p
1.2. System BitRate
08.000Mbps

12
7.1.3.3 CBR-VBR
We can choose between constant (CBR) and variable (VBR) Bit Rates:
7.1.3.4 Video Profile
7.1.3.5 Video Level
7.1.3.6 Audio BitRate
1.3. CBR-VBR
CBR
VBR
1.4. Video Profile
High Profile
Main Profile
Baseline Profile
Auto
-
defect
1.5. Video Level
Level 4
Level 4.1
Level 4.2
Level 1.2
Level 1.3
Level 2
Level 2.1
Level 2.2
Level 3
1.6. Audio BitRate
128Kbps
256Kbps
384Kbps
64Kbps
96Kbps

13
7.1.3.7 PMT PID
7.1.3.8 VIDEO PID
7.1.3.9 AUDIO PID
7.1.3.10 PCR PID
7.1.3.11
Prog. Name
7.1.3.12
Provider
1.7. PMT PID
0256
1.8. VIDEO PID
0257
1.9. AUDIO PID
0258
1.10. PCR PID
0259
1.11. Prog. Name
HD Encoder 1
1.12. Provider
DTV

14
7.1.3.13
Prog. Number
7.1.3.14
Volume Set
7.1.4 Programming of the rest of encoders.
To configure the rest of encoders proceed as it is described above.
7.1.5 ASI
It shows the list of programs that arrives from the ASI input:
7.1.6 Output Setting
7.1.6.1 Output BitRate
1.13. Prog. Number
0256
1.14. Volume Set
16
6.1. Output BitRate
6.2. TS ID
6.3. OR. NET. ID
6.1. Output BitRate
036.000Mbps
Program Total oo
List Empty

15
7.1.6.2 TS ID
7.1.6.3 OR. NET. ID.
7.1.7 IP Output
7.1.7.1 Encoder 1
7.1.7.1.1 Enable
6.2. TS ID
00000
6.3. OR. NET. ID
00000
7.1. Encoder 1
7.2. Encoder 2
7.3. Encoder 3
7.4. Encoder 4
7.5. Subnet Mask
7.6. Gateway
7.7. Local IP
7.8. Local
MAC
7.1.1. Enable
7.1.2. Destination IP
7.1.3. Destination PO
7.1.1. Enable
ON
OFF

16
7.1.7.1.2 Destination IP
7.1.7.1.3 Destination PO
7.1.7.2 Encoder 2
7.1.7.2.1 Enable
7.1.7.2.2 Destination IP
7.1.7.2.3 Destination PO
7.1.2. Destination IP
224.002.002.001
7.1.3. Destination PO
10001
7.2.1. Enable
7.2.2. Destination IP
7.2.3. Destination PO
7.2.1. Enable
ON
OFF
7.2.2. Destination IP
224.002.002.002
7.2.3. Destination PO
10002