Planet FT-712 User manual

Fast Ethernet Converter
100Base-FX
Multi-mode to Single-mode

Trademarks
Copyright PLANET Technology Corp. 2000.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
The information in this manual is subject to change without notice.
All other trademarks belong to their respective owners.
FCC Warning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with this user’s guide, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
Revision
User's manual for PLANET Fast Ethernet Converter
Model: FT-712, FT-722, FT-733, FT-744
Rev 1.0 (Feb. 2000)
Part No. EMFT722V1

1
1. Overview
Thank you for purchasing PLANET FT-7XX family Fast Ethernet
Fiber-optic Converter. This converter is used to convert one type
media signal to other type equivalent that allows two type segments
connect easily, efficiently and inexpensively. This converter can be
used as a standalone unit or as a slide-in module to the 19”media
chassis (up to 10 units) for a multi-mode and single-mode Fiber
combined networks at a central wiring closet. Please contact with
your sales representative for more about the 19”media chassis.
2. Model List
Your Fast Ethernet Converter comes with one of the following
models.
ðFT-712 : one onboard ST and SC fiber connector
ðFT-722 : two on board SC fiber connectors
ðFT-733 : two on board MT-RJ fiber connectors
ðFT-744 : two on board VF-45 fiber connectors
In the following sections, the term “FT-7XX”indicates the product
family above, the term “MM”and “SM”represent Multi-Mode and
Single Mode fiber-optic mode.
3. Checklist
Your FT-7XX carton should contain the following items:
ðThe Fast Ethernet Converter
ðAC-DC Power Adapter (Output: 5VDC, 1 A max.)
ðThis user’s guide
If any item is missing or damaged, please consult the dealer from
whom you purchased your Fast Ethernet Converter.

2
4. Product Outlook
Right View (FT-712/FT-722)
Multi Mode
Single Mode
Two fiber-optic connectors, multi-mode on the left, single-mode
on the right and five LED indicators.
For FT-733, FT-744, the outlook of fiber port is accordant to its
related port, i.e. MT-RJ or VF-45.
Rear View (FT-7XX)
One DC jack for DC power input.
5. Installing the Converter
Please follow these steps to install the converter:
•Turn off the power of the device/station in a network to which
the FT-7XX will be attached
•Ensure that there is no activity in the network

3
•Attach MM fiber cables from the FT-7XX to the MM fiber
network. TX, RX must be paired at both ends
•Attach SM fiber cables from the FT-7XX to the SM fiber
network. TX, RX must be paired at both ends.
•Connect the 5VDC power adapter to the FT-7XX and verify
that the Power LED lights up.
•Turn on the power of the device/station, the Link and LEDs
should light when all cables are attached
FT-7XX
100Base-FX
Multi-Mode
Fiber Network
100Base-FX
Single-Mode
Fiber Network
Note:
nTo prevent from optic acceptor malfunction, check the both
wires before power on the converter.
6. Duplex Mode setting
The FT-7XX is a transparent device between the two fiber
networks, please make sure the both networks are set to the same
duplex environment, or you may get a worse performance in both
networks. Connect with full-duplex Fast Ethernet networks are
strongly recommended.
7.LED indication
LED COLOR DESCRIPTION

4
FX ACT Green Blinks when any FX packet is present
FX Link Green Lit when Fiber connection is good
PWR Green Lit when +5VDC power detected
8. Cable Connection Parameter
Fast Ethernet 100Base-X networks allows 512bit time delay
between any two node stations in a collision domain.
The overall bit time of Fiber wires and devices must be within 512
bit time in a segment.
To extend the distance, you may use switch to break up a collision
domain and extend the distance.
The limitations are as below:
Duplex Connection Limitation (max.)
Multi-Mode
MM Half Node to Node
Node to Switch 412 meters
MM Full Node to Node
Node to Switch 2 kilometers
Single-Mode
SM Half Node to Node
Node to Switch 412 meters
SM Full Node to Node
Node to Switch 20 kilometers
9. FT-7XX Technical Specifications
The FT-7XX comes with the following standard features:
•Standard : IEEE802.3u, 100Base-FX, IEEE802.3x Flow-
Control
•Connectors :
ðOne Fiber-optic, 1300nm wavelength, MM

5
ðOne Fiber-optic, 1300nm wavelength, SM
Connector-type different with models
•Data Transfer Rate :100Mbps
•Duplex mode support :Full or half-duplex mode
•LED indicators :PWR, FX Link, FX ACT, FC
•Power Requirement :5V ,1A
•Ambient Temperature :0°to 70°C
•Humidity :5% to 90%
•Dimension : 26 x 70 x 97mm (HxWxD)
•Cable :
ðMM: 50/125 µm or 62.5/125 µm optic fiber
ðSM: 8.3/125, 8.7/125, 9/125 µm optic fiber
Connecting to Router, Bridge, or Switch, Hub, please refer to the
device’s Technical Manual.
10. Power information
The power jack of FT-7XX is with 2.5mm in the central post and
required +5VDC power input. It will conform to the bundled AC-
DC adapter and Planet’s Media Chassis. Should you have the
problem to make the power connection, please contact your local
sales representative.
Please keep the AC-DC adapter as spare parts when your FT-7XX
is installed to a Media Chassis.
Part No.:EMFT722V1