3One data IMC101GT Series User manual

IMC101GT Series
Industrial Media Converter
Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website:
www.3onedata.com
Te l :
[phone]
Fax:
[phone]
【
Package Checklist
】
Please check whether the package and accessories are intact
while using the media converter for the first time
1. Media converter (equipped with
terminal blocks)
2. Certification
3.
DIN-Rail mounting attachment
4.
Warranty card
5.
Quick installation guide
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【
Product Overview
】
The product is full Gigabit industrial media converter. Models
are:
Model I IMC101GT-1GS (1 Gigabit copper port + 1 Gigabit
SFP)
Model II IMC101GT-1GF (1 Gigabit copper port + 1 Gigabit
fiber port)
【
Panel Design
】
Top view, bottom view and rear view
Front view
Model I Model II
1. Grounding screw (protective ground)
2. Power supply input terminal
3. DIP switch
4. DIN-Rail mounting kit
5. Running status indicator
6. Power supply indicator
7. Copper port connection status indicator
8. Remote alarm indicator
9. Gigabit fiber port
10. Gigabit copper port
11. Gigabit SFP slot
【
Mounting Dimension
】
Unit: mm
Note before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【
DIN-Rail Mounting
】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:

Step 1 Check if the DIN-Rail mounting kit is installed firmly.
Step 2 Insert the bottom of DIN-Rail mounting kit (one side
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Step 3 Check and confirm the product is firmly installed on
DIN-Rail, then mounting ends.
【
Disassembling DIN-Rail
】
Step 1 Device power off.
Step 2 After lift the device upward slightly, first shift out the
top of DIN-Rail mounting kit, then shift out the
bottom of DIN-Rail, disassembling ends.
Note before powering on:
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then
remove the power line, please note the operation order
above.
【
Power Supply Connection
】
DC power supply
This device provides 3-pin industrial terminal blocks (1, 2, 3),
among which 1 and 3 are 12~48VDC power supply inputs.
This power supply supports non-polarity, it
could run normally when reversely
connected.
【DIP Switch Setting】
Provide 4-bits DIP switch for function setting,
where "ON" is enable valid terminal. The
definitions of DIP switch as follows:
No.
Definition
Operation
1
Flow control
Set the switch to ON
2
Specified 100M
Set the switch to ON
3
Remote alarm
Set the switch to ON
4
Jumbo frame mode
Set the switch to ON
【
Checking LED Indicator
】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
Status
Description
RUN
ON /
OFF
Device is in an abnormal state
Blinking Device runs normally
PWR
ON Power supply
is connected and
running normally
OFF Power supply is disconnected or
running abnormally
LINK(G1)
ON Local copper port is connected
properly
Blinking Local copper port is in an active
network state
OFF Local copper port
is not
connected
LINK(G2)
ON Local fiber
port is connected
properly
Blinking Local fiber
port is in an active
network state
OFF Local fiber port is not connected
LFP(G1)
ON
R
emote copper port is not
connected or connected
abnormally
OFF Remote copper port is connected
properly
LFP(G2)
ON
Remote fiber
port is not
connected or connected
abnormally
OFF Remote fiber
port is connected
properly
【
Specification
】
Panel
Gigabit SFP
1000Base-X, SFP slot
Gigabit copper port 10/100/1000Base-T(X)
self-adaption, RJ45 port,
self-
adaptive full/half duplex
mode or specified operating
mode, supports MDI/MDI-X
self-adaption
Gigabit fiber port 1000Base-X
, optional
SC/ST/FC
Indicator P
ower supply indicator,
running indicator, port
indicator, LFP indicator
Switch property
Backplane bandwidth
12G
Buffer size
1Mbit
MAC address
1K
Power supply
Input power supply
DC power supply product
12～48VDC
Support non-
polarity and
anti-reverse connection
Terminal blocks 3-pin 7.62mm
pitch terminal
blocks
Power consumption

Model I No-load: 1.39W@24VDC
Full-load: 1.66W@24VDC
Model II No-load: 1.03W@24VDC
Full-load: 1.27W@24VDC
Operating environment
Operating temperature
-40
～
75
℃
Storage temperature
-40
～
85
℃
Operating humidity
5%
～
95% (no condensation)
Protection grade
IP40 (metal shell)