F&F STR-1 User manual

- 1 -
STR-1
Roller blind controller
2-buttons
The roller blind controller STR-1 is designed for controlling roller
blinds (up and down movement) or other devices (for example,
gates) that are driven by a single-phase AC electric motor and
operated by means of momentary switches (for example, bell-
-pushes). The controller can operate as an independent unit
(designated for opening/closing one roller blind) as well as the
controllers can be combined into groups that enable the central
controlling of many roller blinds.
Supplied the relay is to signal by shine of green LED "U". The
roller blind motor is activated by the momentary switching of
a current pulse (L or N) to one of the control inputs. The motor
is activated at a time programmed previously by the user. The
activation time programmed enables the complete lifting or lo-
wering of the roller blind. Also, there is a possibility of stopping
the rolled blind activated at a level selected by the user (non-
-complete opening or closing of the roller blind).
Purpose
Functioning
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax [phone]
www.fif.com.pl; e-mail: [e-mail]
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collecon, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.

- 2 -
local control – a group of push-buttons that controls one rol-
ler blind which are connect to terminals 5 and 6.
↑ – upwards (opening); ↓ – downwards (closing)
Pressing the local control push-button activates the movement
of the roller blind in a selected direction. If the roller blind is
already moving, pressing the local control push-button will stop
the roller blind.
central control – a common group of push-buttons which
are connect to joint 7 and 8 for many controllers (minimum two
controllers) that controls all roller blinds included in the central
control system.
↑↑ – all upwards; ↓↓ – all downwards.
Pressing the central control push-button activates the move-
ment of the roller blinds in a selected direction. If one of the
roller blinds is already moving in the same direction, its move-
ment will be continued. If one of the roller blinds is moving in
the opposite direction, this roller blind will be first stopped and
then its movement will be activated in the direction in accordan-
ce with the command sent to the central input.
The central control enables only activating the move-
ment of the roller blinds in a selected direction. The
roller blind will be stopped after the programmed move-
ment time or when any of the local control push-buttons
is pressed.
Controller control inputs

- 3 -
1-2 power supply 230 V (L-N)
3 motor power supply – output Down direction ↓
4 motor power supply – output up direction ↑
5 local control – Down direction ↓
6 local control – up direction ↑
7 central control – up direction ↑↑
8 central control – Down direction ↓↓
Control inputs could be supplied from a phase cable
(L) or neutral cable (N). Make a choose of one control
option for all inputs.
Connecting diagram

- 4 -
1.Press and hold a button proG for time when green LED "U"
start to pulsate.
2.When we again press a button proG (Start). Controller start
count a time which is to signal by pulsate of green LED.
3.Press again a button proG (Stop). Controller remember a co-
unted time. Programmin mode is automaticly closed ( green
LED U shine continually).
If at time 30 sec from start programming mode a count
of time doesn’t to start, then controller will out from
programming mode.
Max time for programming 10 min. Test by long time
than 10 min. to cause controller automatically out from
programming mode.
Input to programming mode posible is only when motor
of roller is OFF.
In programming mode a controller doesn’t to react for
outward control signal.
Programming time of enclose

- 5 -
1.Take OFF the power.
2.Put on the controller on the wall or a roller box.
3.3. Connect power cable to terminals 1-2 with marks.
Group of controllers which working with common cen-
tral control should be supplied from the same phase e.g
only L1.
4.Choose control option (control impulse L or N). Switch of local
control and central control connect with marks with function
to terminal to choosen cable (accordance with choosen con-
trol option – L or N).
All control inputs of controllers which works separately
or in group should have to common control impulse
option – all are controlling from the same phase, e.g.
only L1; or all from N.
Choosing control option from phase (L) to control inputs
should be connect to the same phase as for supply e.g.
only phase L1.
Connection different phase e.g. L1 and L2; or phase L
and "zero" N to inputs of control inputs of controller can
cause to wrong work of system and break controllers.
Mounting

- 6 -
5.Controlled roller motor connect properly to terminals 3 and
4 and to N.
6.Take ON the power.
7.Programming to time of upwards/downwards of roller. Pre-
scribed is that programmed time should be longer than 10 sec
from real time of upwards/downwards.
power supply 230 V AC
maximum load current (AC-1/AC-3) 8 A/1.5 A
power of connected single-phase motor 320 W
control triggered by level L or N
control pulse current for L/N <1mA
switch-on time (adjustable) 0 sec÷10 min.
power indication green LED
programming indication green LED
power consumption <1 W
working temperature -25÷50°C
signal terminal 4×DY 1mm², l=10 cm
supply terminal 2×DY 1.5mm², l=10 cm
dimensions ø55, h= 20 mm
mounting in fl ush-mounted box ø60
ingress protection IP20
The controller uses the strength of the contact relay 8 A
to resistive load. Due to the inductive nature of the char-
ge introduced by the engine shutters should not be char-
ged more than the contact current 1.5 A. Corresponds to
power of motor about 320 W.
Technical data

- 7 -
F&F products are covered by a 24-month warranty from the date
of purchase. The warranty is only valid with proof of purchase.
Contact your dealer or contact us directly.
F&F Filipowski sp. j. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE.
The CE Declaration of Conformity, along with the references to
the standards in relation to which conformity is declared, can be
found at: www.fif.com.pl from the product subpage.
Warranty
CE declaration
E200527