F&F AS-224 User manual

- 1 -
AS-224
Staircase timer
with counter-blockade
Staircase timer AS-224 serves to keep switch-ON lighting of stair-
case, corridor, or any other object for the set time and to switch-
OFF this lighting automatically, upon elapse of this set time.
Turned ON staircase timer supports the lighting during set time
by potentiometer (from 0.5 min. to 10 min.) and upon elapse of
this set time a reduction by half of lighting brightness follows
for about 30 seconds, after that OFF follows (thus an occurrence
of a sudden darkness is avoided, enabling safe approach to the
switch). After switching OFF the lighting there is possibility to
switch it ON again. Function of counter blockade does not allow
to keep the light-ON in case of staircase switch blocking (after
blocking the pushbutton, for example by match, the timer will
count the set time and switch OFF the lighting). Next switching
ON can be after removing the blockade.
Purpose
Functioning
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax [phone]
www.fif.com.pl; e-mail: [e-mail]
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collec� on, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regar-
dless of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.

- 2 -
1.Take OFF the power.
2.Put on the relay on the rail in switchgear box.
3.Connect the power cable to terminals 1-3 in accordance with
markings.
4.Timer switches which were connect with parallel, connect to
terminal 6 and to cable which is connecting to terminal 3.
5.Connect the power (L/+) to terminal 10. The supplied receivers
(lamps) which were connect with parallel, connect to terminal
12 and cable N/–.
Mounting
Wiring diagram

- 3 -
AS-224 can’t work with backlit buttons.
power supply
1-3 relay’s power supply 21÷27 V AC/DC
control inputs
6 control input
contact
10 output – COM power supply contact
12 output – closing contact (active)
power supply 21÷27 V AC/DC
maximum load current (AC-1) 16 A
activation delay 0.1÷0.2 s
deactivation delay (adjustable) 0.5÷10 min.
power consumption 0.6 W
terminal 2.5 mm² screw terminals
tightening torque 0.4 Nm
working temperature -25÷50°C
dimensions 1 module (18 mm)
mounting on TH-35 rail
ingress protection IP20
Technial data

- 4 -
supply tungsten halogen fluorescent energy-saving LED
230 V 2000 W 1250 W 1000 W 500 W 250 W
24 V 350 W 200 W – – 150 W
The above data are indicative and will heavily depend on the
design of a specific receiver (that is especially important for
LED bulbs, energy-saving lamps, electronic transformers and
pulse power supply units), switching frequency and operating
conditions.
For more information visit: www.fif.com.pl.
The F&F products are covered by a warranty of the 24 months
from the date of purchase. Effective only with proof of purchase.
Contact your dealer or directly with us.
F&F Filipowski sp. j. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE. The CE Declaration of Conformity, along
with the references to the standards in relation to which con-
formity is declared, can be found at www.fif.com.pl on the prod-
uct page.
Power table
Warranty
CE declaration
E210802