F&F PCZ-526.2 (S) User manual

PURPOSE
FUNCTIONING
Astronomical control timers is as for enclosing and switching off of
illumination or according to other electric receivers 24 hours,
astronomical points of west and sunrise
PCZ-526.2 (S)
PROGRAMMABLE CONTROL TIMERS
astronomic type
The astronomical timer activates and deactivates a device at certain
hour, i.e. at sunrise and sunset. Should more settings that are precise
be required for locations of different geographical co-ordinates, there
is an option to set a given longitude and latitude or select a special
code which entails automatic setting of these co-ordinates for a given
place in Europe (list of locations and their codes may be found in the
manual). Time points of enclosing and exclusion are set by user by
HOUR SLIP MODE or TIME CORRECTION MODE it means , posible
is speed up or delay a programmable time points of enclosing or
exlusioning for sunrise and sunset. Posible is programming a night
break between enclusion and exclusion programming points ( take
off the power for hour to austerity energy).
ASSEMBLY
1. Take OFF the power.
2. Put on the control timer on the rail in the switchgear box.
3. Connect the power cables with wiring diagram.
4 Connect the recuivers with wiring diagram.
5.Set a correct date (see p. 2) and time (see p3)
6.Set to user configuration (see p4)
TECHNICAL DATA
supply
current load
contacts 1P
display maintenance time non
timer maintenance time 6 years
indication accuracy item 1sec
time deviation
working temperature -20÷50°C
connection screw terminals 2
dimensions 2 modules (35mm)
24÷264V AC/DC
2×(<16A)
2×
±1s/24h
schedule time accurancy item 1min
corection activation and deactivation time ±0÷99min
power consumption 1,5W
,5mm²
fixing on the rail TH-35
joint 1-5
programmable
enclosing
point
t1
night break
t2
t
programmable
exclusioning
point
WIRING DIAGRAM
Chanell 1:
joint 1-5 “ENCLOSE” [ON]
joint 1-6 “EXCLUSION” [OFF]
Chanell 2:
joint 2-7 “ENCLOSE” [ON]
joint 2-8 “EXCLUSION” [OFF]
1
5
2
6
3
7
4
8
AC/DC
It touches east and they are defined sunset as moment, when it
touches center of sunny disk horizon it ( parameter h = - 0,583 ° ).
Deviation of row several minute commits from the point of view of
simplification of account relatively to data by indicated „HM Nautical
Almanac Office”.
ATTENTION!
DESCRIPTION OF WORK AND FUNCTIONS
AUTOMATIC WORK - according to program points of enclosures and
switching off joint [sign on the left of display]
HANDIWORK- [ON] - enduring connection of joint (position1-5) or [OFF]-
enduring switch off joint (position 1-6) by activated AUTOMATIC WORK [
lack of sign
ş
ş on the left of display]
PROGRAMMABLE POINT OF ENCLOSURE - time of enclosure in
foothold about astronomical point of sunset indicated joint (position
1-5) and HOUR SLIP by user program and TIME CORRECTION.
PROGRAMMABLE POINT OF EXCLUSION- time of exclusion in foothold
about astronomical point of sunset indicated joint (position1
-6) and HOUR SLIP by user program and TIME CORRECTION.
CONFIGURATION - application of LOCALIZATION and assignment of
POINT OF PROGRAM ENCLOSURE and EXCLUSION
LOCALIZATION - application of CODE COORDINATES or manual optional
setups geographic coordinates ( for CODE COORDINATES 86 - SITE
USER )
COORDINATES CODE - for detailed cities assign city geographic
facilitating inscription localization (coordinates and assign serve codes in
table memorial )
HOUR SLIP - assignment of geographic time zone in range ±1÷12
relatively to universal time greenwich UT (00). For poland + 1 hour. Points
of time east and sunset they undergo parallel slip about served value .
TIME CORRECTION - acceleration or delay of time of enclosure or
relatively to astronomical time points of east exclusion (switching off) and
sunset. Setups in range ±99min for point of west and sunrise are
performed in apart.
DST - Daylight Saving Time - global name of summer time (free translation
time of winning sunny light). Function enabling exclusion automatic change
time.
NIGHT BREAK - set by user time of programming points of enclosure and
exclusion.
CHANNEL - user programming line with sets in KONFIGURATION MODE
and NIGHT BREAK sterring a enclosure joint.
www.fif.com.pl
F&F Filipowski sp. j.
ul. Konstantynowska 79/81
95-200 Pabianice POLAND
tel/fax [phone]
e-mail: [email protected]
F&F products are covered by an 24 months warranty from date of purchase
5 9 0 8 3 1 2 5 9 6 4 2 4

PROG
Mo TUWETHFRSASU
1
ON
OFF
DESCRIPION OF DISPLAY AND PANEL STEERING
Mo-monday;Tu-tuesday; ;Fr-friday; Są-saturday; Su-sundayWe-wednesday;Th-thursday
day of week
signalisation of
joint position
index of
SUMMER TIME
date and time/
registration of programs
ondex of mode
AUTOMATIC
WORK
CHANNEL
PCZ-524.2
RESTART
MENU
OK
+
-
DESCRIPTION OFF BUTTONS FUNCTION
MENU:
- passing from AUTOMATIC WORK to HANDIWORK and inversely
(preeser <2sec)
-passing in CONFIGURATION mode (preeser >3sec). Time must be
in AUTOMATIC WORK mode
- acceptance of settings DATE, TIME AND DST and the rest of settings
of CONFIGURATION mode.
OK:
- approve of registration and passage to next position
- to peep settings podgląd ustawień PROGRAMMABLE POINTS OF
ENCLOSURE AND EXCLUSION
+:
- change setting position by +1 in choosen programable position
(preesing a button make intennsive changes in settings by +1 in loop)
- in HANDIWORK mode:permanent enclosure ON and exclusion OFF
a joint
- in AUTOMATIC WORK mode:to peepsertting of date (dd-mm-yy)
−:- change setting position by +1 in choosen programable position
(preesing a button make intennsive changes in settings by +1 in loop)
RESET:
- to reset a processor - in case of hook-up of function of work
indispensable of timer. It does not erase setups of dates and time and
registration settings.
−+ MENU ("hard" reset) simultaneously prees:
- delete of all settings of date and time and all registration from memory
(preesing >3sec two buttons simultaneously ).
PROGRAMMING
1. START
1.1 Take on the POWER
1.2 Timer sterted count time from hour. 00:00
ATTENTION! If after took the power timer show another time and date
then it means, in memory timer are earlier setting.
1.3Iin order to change of settings, preesing
ATTENTION! If timer have got in memories earlier settings, they could
be deleted by “hard” reset (−+ MENU simultaneously prees >3sec.).
ATTENTION! All earlier configuration will be delete . Timer autoamticly
go to setting mode of date (see 2.1).
MENU >3sec.(see p2.1)
PROG
Mo
1
OFF
2. DATE
Prees a button MENU >3sec.
2.1 Timer pass to setting mode of year.
By buttons +/− set actual year and enter OK.
PROG
By buttons é/ę set a hour.
*By button OK enter a hour .Timer automaticly pass to configuration
mode of DST (see p4.1)
* By button MENU accept all of registry and out of programming mode.
4. DST - automatic change of time winter/summer.
Changes in option DST prees MENU >3sec.
ATTENTION!
changing a date (see p2.1) and time (see p3.1).
4.1 Timer pass to configuration mode of DST.
Changes of DST mode are previoused by checking or
PROG
Mo
1
ON
By button +/− set to :
ON - automatic change time function
OFF - lack of automatic change time function
*Enter to option by button OK. Timer automaticly pass to
CONGIGURATION mode (see p5.1).
*By button MENU/DELETE accept settings and out of programming
mode.
2.2 Timer pass to setting mode of month.
PROG
By buttons +/− set to actual day of month
*by butt on OK pass to c onfiguration mode of ho ur
(see p3.1)
* by button MENU accept to registry and out of programming mode.
ATTENTION! Change from winter time to summer time and inversely is
make automaticly. Choose a date definite a time( winter time or
summer time).
SUMMER TIME- added a sign ş on the right side of display
WINTER TIME- lack a sign ş on the right side of display
ATTENTION! Posible is turn OFF automatic function of change a time
( see p.4).
3. TIME
Changes of time make by prees MENU >3sec.
ATTENTION! Changes of TIME mode are previoused by checking or
changing a date (see p2.1)
3.1 Timer pass to setting mode of minutes.
(hour;minute)
By buttons OK.+/− set to minutes and enter
3.2 Timer pass to setting mode of hour.
PROG
Mo
ş
PROG
Mo
ş
By buttons +/− set actual month and enter OK
2.3 Timmer pass to setting mode a day of month.
.
PROG

5. CONFIGURATION - set to CORRECTION OF TIME,
LOCALIZATION AND HOUR DELAY.
Change CONFIGURATION by prees MENU >3sec.
ATTENTION! C
by checking or changing a date (see p2.1), time (see p3.1) and option.
hanges of CONFIGURATION mode are previoused
5.1 Timer pass to CORRECTION MODE for sunset point.
ATTENTION!
Range from -99min to +99min. Value "-" (minus) to speed up to
enclose by put number of minutes. Value "+" (plus) delay to enclose by
put number of minutes .
00
PROG
Mo TU
1
ON
By buttons .
5.2 Timer pass to CORRECTION TIME mode for sunrise point
ATTENTION!
Range from -99min to +99min. Value "-" (minus) to speed up
switching off by put number of minutes. Value "+" (plus) to delay
switching off by put number of minutes..
+/− set to number of minutes and enter OK
00
PROG
Mo TUWE
1
OFF
By buttons +/− set to number of minutes and enter OK.
5.3 Timer pass to configuration mode of LOCALIZATION.
ATTENTION!
Check coordtinates code table and find a city which is near your
localization and put suitable code. Standard set code is code 19 for
Warsaw
ATTENTION!
Choose and accept of code 24 (USER COORDINATES) cause to
pass to handiwork mode (see p7.2).
By buttonsi set to a value of delay and enter OK.
*Timer automaticly pass to setting mode of NIGHT BREAK. (see p6.1)
*By button MENU accept allow registry and out of programming mode.
+/−
PROG
Mo TUWETHFRSASU
By buttons OK.
5.4 Timer pass to HOUR SLIP mode..
ATTENTION!
Standard setting for POLAND +01. Range from -12hours to +12hours.
Value "-" (minus) to move “for rear” parallel astronomical points of
sunrise and sunset time by put of number hours.
Value "+" (plus) to move “forword” parallel astronomical point of
sunrise and sunset time by number of put hours.
+/− set to code and enter
PROG
Mo TUWETH
6. NIGHT BREAK
Change in option of NIGHT BREAK mode prees MENU >3sec.
ATTENTION! Out of settings from NIGHT BREAK is previoused by
checking and changing of date (see p2.1), time (see p3.1), option DST
(seep 4.1) and KONFIGURATION (see p5.1).
ATTENTION!
If timer have to work out from NIGHT BREAK set the same value
of start and end times.
6.1 Timer pass to setting mode of start minutes of NIGHT BREAK P1
for channel 1(sign 2OFF on the right side).
PROG
1
OFF
By buttons OK.
Timer pass to setting mode of start minutes of NIGHT BREAK..
+/− set to a minutes and enter
By buttons OK.
6.2 Timer pass to setting mode of end minutes of NIGHT BREAK.
(sign 1ON on right side).
+/− set to a hour and enter
By buttons set to a hout and enter OK.
*Timer again pass to setting mode of date.(see p2.1)
*By button MENU acept allow registry and out of programming mode.
+/−
By buttons OK.
Timer pass to setting mode of hour of end of NIGHT BREAK P2 for
channel 2 (sigh 2OFF on right side). Repeat action p6.1 and p6.2 to
channel 2.
+/− set to a minutes and enter
ATTENTION!
* Set a time of NIGHT BREAK make a enclosing and exclusioning of
iont. They are treat as orders and realized in chronology of set time.
Posibility of setting of enclosing and exclusioning time of joints with
accordance PROGRAMMING ENCLOSING AND EXLUSIONIN
POINTS with NIGHT BRAK times are ilustarte by following diagrams.
ON
(20:57)
PPZW
OFF
(23:30)
PN
1 5
OFF
(04:23)
ON
(03:15)
ON
(20:57)
PPZW
OFF
(19:30)
PN
1 5
OFF
(04:23)
ON
(03:15)
ON
(20:57)
PPZW
OFF
(23:30)
PN
1 5
OFF
(04:23)
ON
(05:15)
ON
(20:57)
PPZW
OFF
(19:30)
PN
1 5
OFF
(04:23)
ON
(05:15)
ON
(20:57)
PPZW
ON
(23:30)
PN
1 5
OFF
(04:23)
OFF
(03:15)
setting time of end break
before start time of break
ON
(20:57)
PPZW
OFF
(00:00)
PN
1 5
OFF
(04:23)
ON
(00:00)
setting of the same times
of start and the end of break.
OUT FROM NIGHT BREAK
PPZW - programmable points of enclosing and excusioning
PN - night break
- joint position ( - joint enclosed)
P i
PROG
1
OFF
PROG
1
ON
P i
PROG
1
ON

By buttons .+/− set to minutes and enter OK.
7.4 Timer pass to of setting mode of minutes of geografical lenhgt
coordinates.
7.1 Pass to handiwork setting mode of geografical coordinates is
previoused by pass of CONFIGURATION MODE (see p5). In setting
mode of COORDINATES CODE set to code of number 86 (USER
COORDINATES) and enter OK.Timer pass to setting mode of
geografical coordinates
ATTENTION!
Standarts setting coordinates for Warsaw (52°15'N 21°00'E)
7.2 Timer pass to setting mode of width minutes (sign L on the left).
7. HANDIWORK SETTING GEOGRAFICAL COORDINATES
By buttons +/− set to value and enter OK..
7.3 Timer pass to of setting mode of geografical coordinates.
l i5
PROG
Mo TUWETHFR
PROG
Mo TUWETHFR
ş
ATTENTION!
Value up than “zero” mean north of geografical coordinates.
Value down than “zero” mean south geografical coordinates .
width
width
PROG
Mo TUWETHFRSA
By buttons +/− set to minutes and enter OK..
7.5 Z
coordinates..
Timer pass to of setting mode of minutes of geografical lenght
By buttons
Timer pass to setting mode of HOUR SLIP (see p5.4).
+/− set to value and enter OK.
PROG
Mo TUWETHFRSA
ATTENTION!
Value up than “zero” mean east of geografical lenght coordinates.
Value down than “zero” mean west of geografical lenght coordinates
If you want to delete all settings of DATE, TIME and CONFIGURATION
you must together preesing a buttons MENU and − for >3sec.
9. RESET
Restart od procesor is needed when all function of timer are to stoped.
Don’t delete settings of DATE, TIME and CONFIGURATION MODE
from memories. Prees a button RESET for <1sec.
8. DELETED MEMORIES - "hard” reset
PEEP TO A DATE
In AUTOMATIC WORK prees a button +. Timer displaing a set date
(dd-mm-yy). After 5 sec timer automaticly pass to central level.
AUTOMATIC FUNCTION OF TIME CHANGE !
Changes time from winter time to summer time is autmaticly make at
the last sunday of march at 2 a.m. ( add 1 hour to actual time) .
ATTENTION! Possible is take OFF automatic function of time change
(see p.4).
PROGRAMMABLE POINTS
ASTRONOMICAL POINT SUNSET
SUNRISE
HOUR SLIP
TIME CORRECTION ENCLOSURE
EXCLUSION
ENCLOSURE
EXCLUSION
21:19
-15min
-02
00
+01
+20min
4:01 1:19
18:19
19:59
3:16
20:19
3:01
Example table with enclosure and exclusion points
on 22.06.2006
for choosen settings of CONFIGURATION
PEEP TO A
AND EXCLUSION
PROGRAMMABLE POINT OF ENCLOSURE
In AUTOMATIC WORK mode next preeser a button OK. see a next
seetings in configuration:
- programmable point of enclosure foe channel 1
- start of night break P1
- end of night break P1
- programmable point of exclusion for channel 1
- programmable point of exclusion for channel 2
- start of night break P2
- end of night break P2
- programmable point of exclusion for channel 2
After 5 sec. timer automaticly pass t o central level

C121008
Code City Longitude Latitude Device OFF
1 Finland Helsinki 60:08:00 °N 025:00:00 °E
2 Finland Kuopio 62:54:00 °N 27:41:00 °E
3 Finland Rovaniemi 66:33:07 ºN 25:50:51 ºE
4 Norway Andenes 69:19:12 °N 16:07:12 °E 21.05÷23.07
5 Norway Alta 69:34:48 °N 23:15:00 °E 20.05÷21.07
6 Norway Bardufoss 69:02:24 °N 18:37:12 °E 22.05÷21.07
7 Norway Berlevåg 70:30:36 °N 29:04:48 °E 16.05÷28.07
8 Norway Bodø 67:10:12 °N 14:22:48 °E 03.06÷10.07
9 Norway Harstad 68:28:48 °N 16:32:24 °E 27.05÷18.07
10 Norway Hammerfest 70:40:12 °N 23:40:48 °E 15.05÷30.07
11 Norway Narvik 68:26:00 °N 017:25:00 °E
12 Norway Nordkapp 71:06:00 °N 25:47:24 °E 15.05÷31.07
13 Norway Oslo 59:56:00 °N 010:17:00 °E
14 Norway Svolvær 68:08:24 °N 14:33:36 °E 28.05÷16.07
15 Norway Tromsø 69:39:00 °N 18:57:36 °E 20.05÷24.07
16 Norway Trondheim 63:36:00 °N 010:23:00 °E
17 Norway Vardø 70:13:48 °N 31:06:00 °E 17.05÷27.07
18 Poland Pabianice F& F 51:40:12 °N 019:33:36 °E
19 Polend Warszawa 52:15:00 °N 021:00:00 °E
20 Sweden Goteborg 57:45:00 °N 012:00:00 °E
21 Sweden Lulea 65:36:00 °N 22:09:00 °E
22 Sweden Malmö 55:35:00 °N 013:00:00 °E
23 Sweden Stockholm 59:20:00 °N 018:05:00 °E