FBII OMNI-624EU User manual

+
+D DU UG GZ ZL LU UH HG G : :L LU UH HO OH HV VV V 6 6\ \V VW WH HP P
O
OM MN NI I- -6 62 24 4
O
OM MN NI I- -6 62 24 4E EU U
User Guide
ARMED
READY
1
4
7
2
5
8
0
3
6
9
#
STAY
BYPASS
INSTANT
CODE
ARMED
READY
1
4
7
2
5
8
0
3
6
9
#
STAY
BYPASS
INSTANT
CODE
1 3
2
4 6
5
7 9
8
#
0
STAY INSTANT
BYPASS CODE
ARM
AC / LB
READY
STAY
INST
LO BATT
SPRV.
N9968V1 3/01

- 2 -
Table of Contents
QUICK REFERENCE.......................................................................................................................4
INTRODUCTION..............................................................................................................................6
SYSTEM REFERENCE ...................................................................................................................7
ZONE DESCRIPTIONS................................................................................................................7
SEND HELP ALERT.....................................................................................................................8
PAGER ALERT.............................................................................................................................8
MONITORING STATION INFORMATION ...................................................................................8
USER CODE ASSIGNMENTS.....................................................................................................9
ARMING THE SYSTEM.................................................................................................................10
IS THE SYSTEM READY?.........................................................................................................10
TO ARM THE SYSTEM AND LEAVE ........................................................................................10
WHEN THE SYSTEM IS NOT READY......................................................................................11
TO ARM THE SYSTEM AND STAY INSIDE..............................................................................12
TO ARM THE SYSTEM IN INSTANT MODE AND STAY INSIDE.............................................12
TO ARM THE SYSTEM IN INSTANT MODE.............................................................................13
TO BYPASS A ZONE.................................................................................................................13
TO UNBYPASS A ZONE............................................................................................................14
DISARMING THE SYSTEM...........................................................................................................15
USER CODES................................................................................................................................16
TO ADD OR CHANGE A USER CODE .....................................................................................16
TO DELETE A USER CODE......................................................................................................17
MISCELLANEOUS COMMANDS..................................................................................................18
TO SEND HELP ALERTS ..........................................................................................................18
DURESS.....................................................................................................................................18
QUICK ARMING.........................................................................................................................18
QUICK FORCED ARMING.........................................................................................................18
QUICK BYPASS.........................................................................................................................19
QUICK EXIT ...............................................................................................................................19
TO TURN CHIME ON/OFF.........................................................................................................19
ASSIGN USERS ACCESS TO OTHER PARTITIONS ..............................................................20
CHANGE PARTITION................................................................................................................20
TO SET AUTO-ARM TIME.........................................................................................................20

- 3 -
TO VIEW QUICK COMMAND LIST (LCD KEYPADS ONLY)....................................................20
TO VIEW AUTO-ARM TIME (LCD KEYPADS ONLY)...............................................................20
DOOR STRIKE...........................................................................................................................21
TO VIEW TIME (LCD KEYPADS ONLY) ...................................................................................21
TO SET TIME .............................................................................................................................21
TO DISPLAY ZONE DIRECTORY (LCD KEYPADS ONLY)......................................................21
USER LOG VIEW (LCD KEYPADS ONLY) ...............................................................................21
KEY FOB LOW-BATTERY TEST...............................................................................................22
ON-LINE DOWNLOAD...............................................................................................................22
USING A PAGER...........................................................................................................................23
CHANGING THE PAGER PHONE NUMBER (FOLLOW-ME)...................................................23
TURN PAGER REPORTING ON/OFF FOR THE PARTITION..................................................24
TURN PAGER REPORTING ON/OFF FOR A USER................................................................24
TESTING THE SYSTEM................................................................................................................25
SYSTEM TEST...........................................................................................................................25
BATTERY TEST.........................................................................................................................25
RECOMMENDATIONS ON SMOKE DETECTORS......................................................................26
EMERGENCY EVACUATION .......................................................................................................27
GLOSSARY ...................................................................................................................................28
RADIO FREQUENCY EMISSIONS STATEMENTS......................................................................32
TELEPHONE/MODEM INTERFACE STATEMENTS ...................................................................32
TELEPHONE OPERATIONAL PROBLEMS.................................................................................33
O560 DECLARATION OF CONFORMITY...............................................................................33
LIMITATIONS OF THIS ALARM SYSTEM...................................................................................34

- 4 -
Quick Reference
TO ARM THE SYSTEM
1. Check to make sure the system is ready. (Green READY light is lit).
2. Enter your 4-digit (or 6-digit) user code.
The ARMED light will light.
3. Exit through a door designated by your installer as an exit/entry door.
NOTE: If you DO NOT EXIT during the exit time and your system installer has
programmed your system for Auto-Stay, the system will arm in the Auto-Stay
mode.
TO DISARM THE SYSTEM
1. Enter through a door designated by your installer as an exit/entry door
2. Enter your 4-digit (or 6-digit) user code.
3. The system ARMED light will go out.
TO ARM THE SYSTEM AND STAY INSIDE
1. Check to make sure the system is ready (Green READY light is lit).
2. Press STAY .
3. Enter your 4-digit (or 6-digit) user code.
The ARMED light and the STAY light will both light.
REMEMBER: Unless the Quick Exit feature is enabled, you must disarm the
system if you want to open a premises entry/exit door after the exit time has
passed.
TO ARM THE SYSTEM IN INSTANT MODE, AND STAY INSIDE
1. Check to make sure the system is ready (Green READY light is lit).
2. Press INSTANT .
3. Press STAY .
4. Enter your 4-digit (or 6-digit) user code.
The ARMED light, the INSTANT light, and the STAY light will all be on.
TO RESET SMOKE DETECTOR
1. Enter your 4-digit (or 6-digit) user code twice.

- 5 -
Quick Reference (Cont’d)
The following table lists the “Quick Commands” available with this control.
Key Description Keypads Comments
# 1Quick Arm – if system is ready All keypads Allows you to arm the system without requiring
your user code. User code is always needed to
disarm the system.
# 2Force Arm – bypasses faulted
zones All keypads Allows you to arm the system even if some zones
are faulted. These zones will be automatically
bypassed and will be unprotected.
BYPASS
nn (zone no.)
Quick Bypass All keypads If not enabled, requires user code with authority 1,
2, or 3.
# 3Set Time and Date All keypads May require user code.
# 4Zone Directory LCD* only Lists each zone with its descriptors. Mode
terminates after last enabled zone.
# 50 Quick Help LCD* only Provides a listing of all quick commands available
in the system.
# 51 Show Time and Date LCD* only May also require code.
# 52 Show Auto Arm Time LCD* only May also require code.
# 53 User Event Log View LCD* only Also needs user code with authority level 1 or 2.
# 54 Set Auto Arm Time of
Current Partition All keypads By partition, may also require code.
# 55 Display Firmware Version LCD* only Displays panel’s revision.
# 56 Display Key Fob Low
Batteries All keypads Wireless Key Fob battery test.
# 57 Door Strike All keypads Activate doorstrike or trigger. May require certain
user code.
# 58 Change/View Pager Number All keypads For keypad partition, only LCD* shows phone
number.
# 6Display/Toggle Chime Mode All keypads LCD* displays current state first, then offers to
toggle. All others just toggle the state.
# 7Assign User to Other
Partition or to Activate
Paging
All keypads Need user auth. of 1 or 2. Digit 4 (P) enables user
to page.
Paging must be enabled and turned on.
# 8User Page Toggle All keypads Toggles if users should send page for
Open/Close by partition.
# 9User On-line All keypads Connects to downloader while on line, disconnects
home phone.
# 0Multi-Partition All keypads LCD* displays current enables, 1,2,P - P=4
* 2-line alpha display

- 6 -
Introduction
Congratulations on your decision to protect your home or business with the
OMNI-624 or OMNI-624EU security system. You have chosen a reliable, state-of-
the-art security system that is remarkably easy to operate. Your system has been
professionally installed by your local Security Company, whose representative
can explain the specifics of your system.
The keypad is the input and display device for your security system. Your
Security Company representative will suggest the model most appropriate for
your premises and your needs. There are three types of keypads that can be used
with this system:
LCD keypad (alpha display), fixed-word keypad (2-digit display), LED keypad.
Since your system may use any of these keypads, the displays of all keypads are
described in this manual.
The OMNI-624 is listed by Underwriters Laboratories for Household Fire and
Burglary applications.
Throughout this manual, the following conventions are used to represent the
keystrokes required to perform the following functions.
STAY Press button labeled STAY.
BYPASS Press button labeled BYPASS.
INSTANT Press button labeled INSTANT.
CODE Press button labeled CODE.
Enter 4-digit (or 6-digit) user code.
Please keep your manual in a convenient location so you can refer to it
if needed.

- 7 -
System Reference
ZONE DESCRIPTIONS
In the following table, enter a description of the area of protection for each
zone.
Example: Zone 1 Windows on north side of building
Zone 4 Main entrance to building.
Zone Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Entry time ________ Door __________ Exit time ________
Entry time ________ Door __________
Exit time is the same for all designated entry/exit doors.

- 8 -
System Reference (Cont’d)
SEND HELP ALERT
All keypads are equipped with emergency-pair keys. In order to
activate the alert, both keys must be pressed at the same time. The
type of keypad you have installed dictates which keys you press. Your
installer will show you how to activate these emergency keys. The emergency
keys used for all keypads are shown below.
The following SEND HELP ALERT is programmed into my system:
KEYS DESCRIPTION
[#] & [✱]
[7] & [9]
[1] & [3]
PAGER ALERT
If programmed, a button on a designated keyfob may also be used to send an
alert message to a pager. Ask your installer if this was done.
MONITORING STATION INFORMATION
Account #
Telephone #

- 9 -
System Reference (Cont’d)
USER CODE ASSIGNMENTS
In the following table, enter the names of the individuals assigned to each
user number.
User Assigned To… User Assigned To…
117
218
319
420
521
622
723
824
925
10 26
11 27
12 28
13 29
14 30
15 31
16 32
____ ____ USER CODE NOTE: User codes can be either 4 digits or 6 digits, depending
4-digit 6-digit on installer programming. Ask your installer what type of user codes (4- or 6-
digits) are being used in your system. When performing system functions, you
must use the appropriate 4 or 6-digit user codes.

- 10 -
Arming the System
IS THE SYSTEM READY?
You can arm and disarm the burglar portion of your security system. Before
you can arm the system, it must be “ready.” If you have a protected door
open, or someone is moving in view of a motion detector, the system will not
display the “READY” message.
The system is ready if the READY light and the display show:
LCD Keypad:
SYSTEM READY
PART 1
Fixed-Word Keypad:
“Ready” LED lit LED Keypad: “Ready” LED lit
NOTE: If programmed by your installer, you may arm the system if a delay
or interior zone is faulted. However, faulted zones must be restored before
your exit time expires or an alarm or zone bypass will result. Ask your
installer if your system has this feature and if so, if it causes an alarm or
zone bypass.
TO ARM THE SYSTEM AND LEAVE
Enter your user code.
The System ARMED light will go on and the display will show:
LCD Keypad:
ON: AWAY 120s
PART 1
Fixed-Word Keypad:
“Armed” LED lit
120
LED Keypad:
“Arm” LED lit
NOTE: The number 120 shown above for the LCD and Fixed-Word keypads
indicate a counter that is updated every second and displays the amount of
time remaining to exit without sounding an alarm.
Exit through a door designated by your installer as an exit/entry door. You
must leave within the exit time programmed by your installer. Refer to the
reference sheet for the time that has been set for your system.
This system can be programmed by the installer for the AUTOSTAY feature,
which automatically bypasses interior zones if you arm the system and do not
exit through a delay zone during exit time.