FBII XL-2T User manual

X
XL L- -2 2T T
Security System
User Guide
N9819V3 2/00
FIRE BURGLARY INSTRUMENTS,
INC.

- 2-
Table Of Contents
QUICK REFERENCE.......................................................................................................................3
INTRODUCTION............................................................................................................................5
SYSTEM REFERENCE...................................................................................................................6
TURNING THE SYSTEM ON........................................................................................................9
TURNING THE SYSTEM OFF....................................................................................................12
USER CODES.................................................................................................................................13
MISCELLANEOUS COMMANDS.............................................................................................14
TESTING THE SYSTEM..............................................................................................................16
NATIONAL FIRE PROTECTION ASSOCIATION RECOMMENDATIONS ON SMOKE
DETECTORS..................................................................................................................................17
EMERGENCY EVACUATION.....................................................................................................18
GLOSSARY....................................................................................................................................20
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT............................23
TELEPHONE OPERATIONAL PROBLEMS...........................................................................23
LIMITATIONS OF THIS ALARM SYSTEM............................................................................25
LIMITED WARRANTY................................................................................................................28

- 3-
Quick Reference
TO TURN SYSTEM ON
1. Check to make sure the system is ready, (Green READY light is
lit†).
2. Enter your 4-digit user code.
3. Exit through a door designated by your installer as an exit/entry
door.
4. The ON/OFF (ARM) light will light.
TO TURN SYSTEM OFF
1. Enter through a door designated by your installer as an exit/entry
door
2. Enter your 4-digit user code.
3. The system ON (ARM) light will go out.
TO TURN SYSTEM ON AND STAY INSIDE
1. Check to make sure the system is ready (Green READY light is
lit†).
2. Press STAY .
3. Enter your user code.
The ON/OFF (ARM) light and the STAY light will both light.
REMEMBER: You must turn the system OFF if you want to open the door
or leave the premises after the exit time has passed.
TO TURN THE SYSTEM ON: INSTANT MODE, AND STAY INSIDE
1. Check to make sure the system is ready (Green READY light is
lit†).
2. Press INSTANT .
3. Press STAY .
4. Enter your user code.

- 4-
The ON/OFF (ARM) light, the INSTANT light, and the STAY light will
all be on.
TO RESET SMOKE DETECTOR
1. Enter your 4-digit user code.
=READY light is not available on all keypads.

- 5-
Introduction
Congratulations on your decision to protect your home or business
with the XL-2T security system. You have chosen a reliable, state-
of-the-art security system that is remarkably easy to operate. Your
system has been professionally installed by your local Security
Company whose representative can explain the specifics of your
system.
The keypad is the input and display device for your security system.
Your Security Company representative will suggest the model most
appropriate for your premises and your needs.
The XL-2T is listed by Underwriters Laboratories for Household
Fire and Burglary applications.
Throughout this manual, the following conventions are used to
represent the keystrokes required to perform the following
functions.
STAY Press button labeled STAY.
BYPASS Press button labeled BYPASS.
INSTANT Press button labeled INSTANT.
CODE Press button labeled CODE.
Enter 4-digit user code.
Please keep your manual in a convenient location so you can
refer to it if needed.

- 6-
System Reference
ZONE DESCRIPTIONS
In the following table, enter a description of the area of protection
for each zone.
Example: Zone 1 Windows on North side of building
Zone 4 Main entrance to building.
ZONE DESCRIPTION
1
2 _______________________________________
3
4
5
6
7
Entry time ________ Door __________ Exit time ________
Entry time ________ Door __________
Exit time is the same for all designated Entry/Exit doors.
SEND-HELP ALERT
All keypads are equipped with emergency-pair keys. In order
to activate the alert, both keys must be pressed at the same
time. The type of keypad you have installed dictates which keys you
press. Your installer will show you how to activate these emergency
keys. The emergency keys used for all keypads are shown below.
The following SEND - HELP ALERT is programmed into my
system:
KEYS DESCRIPTION
[#] & [QQ ] (Right=)__________________________________
[7] & [9] (Left=)__________________________________
[1] & [3] (Center=)__________________________________

- 7-
=Buttons on XL-4600SM keypad only

- 8-
System Reference (cont)
USER CODE ASSIGNMENTS
In the following table, enter the names of the individuals assigned
to each specific User ID number.
USER ID ASSIGNED TO
1(MASTER USER * )
2(MASTER USER * )
3
4**
5
6
7
8
9
10
11
12
13 Door Strike - Yes No If No
______________________
(If user 13 is not assigned to door strike, then any user can
activate the door strike.)
14 Only Turns System ON -Yes If No
__________________
15 Ambush/Duress Code -Yes If No
___________________
* Master Users can add, change, or erase other user codes.
** If your installer enables only User 4 to report openings and closings to the
CS, then only those person(s) that you assign User 4 ID to will cause a report
to be generated.
MONITORING STATION INFORMATION

- 9-
Account #
Telephone #
Turning The System On
IS THE SYSTEM READY?
You can turn the burglar portion of your security system ON and OFF. Before
you can turn the system ON, it must be “ready.” If you have a protected door
open, or someone is moving in view of a motion detector, the system will not
display “READY.”
The system is ready if the READY light is ON or if the display shows:
SYSTEM READY
WHEN SYSTEM IS NOT READY
If the system is not ready to be armed, the READY light will be OFF and the
zone lights will show which zone or zones are not ready. The following
conditions will be indicated by the zone lights or described on the display:
Fast Blink ...................................Alarm
Slow Blink/Low Intensity .........Bypass
Slow Pulse ..................................Trouble
Solid ON .....................................Not Ready
Example: If the READY light is not lit and the Zone 1light is solid ON, an
alarm sensor on Zone 1 is faulted. This might mean that a door is open or
someone is walking in view of a motion sensor. Check all sensors on Zone 1 and
resolve the problem. When all sensors are restored, the READY light will come
ON and the zone light will go out. In this example, the display shows:
SYSTEM NOT READY
Determine which zone or zones are not ready, resolve the problem, and turn the
system ON normally. If the problem cannot be resolved, you may bypass the
zone that is not ready. Bypassing should only be done if the problem on the zone
cannot be resolved, OR if you intentionally wish to leave the zone OFF.
For example, you would leave the zone OFF if you plan to keep the window open
for ventilation. Zones that are bypassed are not protected when the
system is ON. See Bypass on the following page for a description of the
procedure.
and NOT RDY ZONE 1
FRONT DOOR

- 10 -
Turning The System ON (cont)
TO TURN SYSTEM ON AND LEAVE
Enter your 4-digit user code.
The System ON, (ARM) light will go ON or the display will show:
ON: AWAY ........
Exit through a door designated by your installer as an exit/entry door. You must
leave within the exit time programmed by your installer. Refer to the reference
sheet for the time that has been set for your system.
TO TURN SYSTEM ON AND STAY INSIDE
To turn the perimeter portion of your burglar alarm ON and move around freely
inside the premises, use the STAY mode.
Check to make sure the system is ready. When it is ready, press:
STAY followed by your user code.
When the system has been turned on successfully, the ON/OFF (ARM) light
and the STAY light will be lit, or the LCD will display:
ON: STAY
REMEMBER: You must turn the system OFF if you want to open the door or
leave the premises after the exit time has passed.
TO TURN SYSTEM ON IN INSTANT MODE AND STAY INSIDE
In INSTANT STAY mode, the perimeter portion of your burglar alarm system
is ON and the time delays are eliminated from your normal Entry/Exit door(s).
All interior protection is OFF, so you are free to move around inside.
Check to make sure the system is READY. When it is ready, press:
INSTANT followed by
STAY followed by your user code.
When the system has been turned ON successfully, the ON/OFF (ARM) light,
the INSTANT light, and the STAY light will all be ON, or the LCD will
display:
ON: STAY INSTANT