FBII LEGEND 7100 User manual

LEGEND
@S E R I E S
r-e-,
‘-
,- .- .- _
/ENPAss
’ --4
7
c--.-
1 *
‘-
8
9
- .-
,o *‘n
Id
Owners Manual

INTRODUCTION.
Congratulations on your decision to protect your home or
business with the LEGEND Security System. The system has been
designed with reliability and ease of operation in mind.
Please take afew minutes to review the contents of this manual.0
In order to realize the full potential of this system it is important that
you feel comfortable with its operation. The following pages will
familiarize you with the procedures for operating the LEGEND
Security System.
Thank You,
FIRE BURGLARY INSTRUMENTS

LEGEND Users Manual
Table of Contents
Introduction ............................................. 1
Keypad Layout ....................................... 3
System Operation ................................... 6
Arming ....................................... 7
Stay ........................................... 8
Instant ........................................ 9
Instant-Stay ............................... 9
Bypass ...................................... .10
Forced Arming ........................... 11
Unbypass ................................. -11
Disarming ................................. .12
Keypad Emergency Conditions.. 13
User Definition ........................................ 15
Glossary .................................................. 17
Owners Information ................................ 19
.About the Manufacturer ....................... .:21
Additional Notes ..................................... 24
2

KEYPAD OPERATION
3
The keypad contains everything necessary to operate your
LEGEND Security System. The keypad has the following
appearance;
I 2 3 4
I I[ I
l- ZONE STATUS ‘7
The indicator lights marked 1-16 display the current status of
the zones connected to your LEGEND Security System. The lights
show whether any zones are currently in alarm, bypassed, in
trouble or faulted status. Note: If your system contains eight zones
then only the zones labelled l-8 will be active.
The status of each zone is represented as follows;
ALARM
TROUBLE ’ : : : : : .Fast Blinking .Slow Pulse n
k
BYPASSED . . . . . .Slow low’lntenslty bllnklng
NOT READY . . . . .Solld ON
Each light will only reflect one condition at a time. If a zone ,
contains multiple conditions at the same time the highest priority
status from the above list will appear.

2- LOW BATTERY
The BAT indicator indicates that the ,backup battery within the
system is low.
3- STAY
The STAY light will be ON when the system has been armed in
the stay mode which means that the system has been activated
with the exception of interior zones.
4- READY INDICATOR
The light marked RDY shows whether the system is ready fo be
armed. If the light is off then a condition exists within at least one
of the zones which prevents the system from being armed.
5 COMMUNICATIONS FAILURE
If the COM light is ON then there has been a communications
error with the Central Station.
6- INSTANT
The INS indicator will be ON when the system has been armed
in the INSTANT mode. This means that the system has been
activated and the entry delay has been eliminated.
7- NUMERICAL SECTION
The numericai section of the keypad operates similar to a
calculator or typewriter. The digits 0 - 9 are clearly marked and are
used to enter your access code to control the Security System.
8- PULL OPEN DOOR
The front of the keypad contains a door which pulls open.
Behind this door is a card which can be filled out to describe the
areas protected (zones) of your Security System.
4

9- AC INDICATOR
This light indicates that AC power is connected to the Security
System. Battery backup exists to operate the system in the event
of a power failure.
lo- ARM/DISARM INDICATOR ?
‘\
This light indicates whether the system is currently ARMED
’ (ON) or DISARMED (OFF). In addition to this constant visual
indication, the zone indicator lights will provide” additional
information concerning the current zone status. This light will also
blink if there is a visual alarm condition present.
1% STAY Key
The STAY key is used to activate (arm) the system with the
exception of interior protection. This will provide exterior protection
of your location while allowing full access through the location. This
mode would be used when arming the system and you might be
walking through protected interior zones.
12- BYPASS Key
The BYPASS key will be used to temporarily turn off protection
of a portion of your burglary protection. This could be performed,
for example, to ignore an open window which would prevent the
arming of your system.
13. INSTANT Key
The INSTANT key is used to activate (arm) the system and
eliminates the entry delay. This would cause an immediate alarm if
someone came through an exit/entry zone. (7 /
14- CODE Key
Function key used when entering or changing the User access
codes of your system.
5

SYSTEM OPERATION
Throughout the users manual the following notation will be used
to describe actions taken at the LEGEND-100 keypad;
BYPASS
INSTANT
STAY
CODE
[USER]
l
Function key labelled BYPASS
Function key labelled INSTANT
Function key labelled STAY
Function key labelled CODE
Entry of your four digit user code
Key labelled * (to the left of 0)
#
+
Key labelled # (to the right of 0)
Indicates the simultaneous
entry of two keys. For example,
# + 3, indicates that the # and 3
keys should be pressed at the
same time.
6

ARMING THE SYSTEM
ARMING the system will activate all portions of your Security
System. Arming can only be performed if all zones are READY. For
example, if a protected door is open the system cannot be armed.
SYSTEM READY c
The system is ready to be armed if the READY indicator light
located in the display portion of the keypad is ON. Ifthe system is
ready, ARMING can be performed as follows;
ARMING PROCEDURE
-J.
1. Enter your four digit user code into the keypad:
[USER]
b The,ARMED indicator’light will now be lit and if you are leaving
the home you may exit through a door designated by your installer
as an exit/entry zone for afixed time period known asthe exit delay.
SYSTEM NOT READY
Ifthe system is not ready to be armed the READY indicator will
be OFF. The zone indicator lights will display the zones which are
currently not ready. The condition of each zone indicator reflects
what the status of each zone as follows;
ALARM . . . . . . . Fast blinking.
BYPASS . . . . . . .Slow blinking low Intensity.
TROUBLE . . . . . .Slow pulse
NOT READY . . . . .Solld ON
In order to make the system ready ready determine which zones
are not ready by observing the zone indicator lights. From the zone
number you can find out which area of protection is not ready.
For example, assume the the zone 3 indicator light is ON. c This
means zone 3 is not ready. Typically this might mean that a
protected door or window is open.
>> Once, the problems with each zone has been resolved the
READY light will appear and the system can be armed.
7

To arm the system in this situation one of the following actions
are necessary;
- Make the zone(s) ready. Determine which zones are not ready
and perform what is necessary to ready the zone(s) (example,
close the door or window, etc),
l ’
or
- Bypass the zone(s) not ready. Bypassing should only be
performed if the zone cannot be made ready or intentionally will
remain not ready. Remember, zones that are bypassed are not
protected when the system is armed.
STAY
The STAY mode is another way to ARM your system while you
remain in the location. The STAY mode will deactivate any interior
protection zones which means that you will be free to walk
throughout your location without activating the alarm system.
In order to enter the STAY mode, the system must be READY.
(see previous description).
STAY PROCEDURE:
STAY [USER]
Depress the STAY key followed by’your user code.
After a sucessful STAY arming the ARMED and STAY indicator
will be lit. In the STAY mode only the external or perimeter burglary
Protection is active. You are free to walk around the residence
hithout activating any of the interior protection zones.
>> Remember, you must DISARM the system to when you want
to leave the premise.
Note: The STAY option will automatically be reset after the
system is disarmed.
8

INSTANT ,
The INSTANT mode arms the system and eliminates the entry
time delay interval. If anyone enters through an entry/exit zone the
alarm system will instantly activate.
The system must be ready to select the INSTANT option. r>
. k
INSTANT PROCEDURE .
INSTANT [USER]
Depress the INSTANT key followed by your user code.
Upon sucessful INSTANT ARMING of the system the ARMED
and INSTANT indicators will be lit.
Note: The INSTANT option will automatically be reset ,after the
system is disarmed.
INSTANT - STAY
The. INSTANT STAY mode will arm the system with the
characteristics of both the INSTANT and STAYmodes. The system
will be armed with the interior portions bypassed and the entry
delay will be suspended.
The system must be READY in order to enter this mode.
PROCEDURE
INSTANT STAY [USER]
STAY PN~STANT[USER] r‘,
\\
Depress the INSTANT and STAY keys in any order followed by
your user code.
After a sucessful INSTANTSTAY arming the ARMED, INSTANT
and STAY indicators will be lit.
9