Fellowes Venus 125 User manual

http://www.monomachines.com
Please read these instructions before use.
Veuillez lire ces instructions avant utilisation.
lea estas instrucciones antes del uso.
http://www.monomachines.com

http://www.monomachines.com
ENGLISH
HeatGuard TechnologyTM double·walled
insulation keeps heat inside
Opening lid to clean
laminating mechanism
Discrete carry
handles at side
CAPABILITIES
Pouch Thickness
Estimated Heat·Up Time
Approximate Coo I· Down Time
Lamination Speed
Maximum Width
Voltage
Frequency
~:: ~iiii .. ~~~~~ :::;::;;---~=----- user guidance
.;::::;;;;;-=--
Temperature controlled
release trigger for lid
IMPORTANT SAFETY INSTRUOIONS -
IAWARNINGI
• The socket·outlet shall be installed near the equipment and
shall be easily accessible.
• To prevent electrical shock, do NOT use laminator close to
water and do NOT spill water on laminator, electric cord, or
wall socket.
• Do not leave electric cord in contact with a warm surface.
• Do not leave electric cord hanging from a cupboard or shelf.
• Do not use laminator if electric cord is damaged.
• Do not laminate metal objects.
IMPORTANT SAFETY INFORMATION
3·10 mil
Laminating capacity - 3to 10 mil hot laminating pouches per side
4 Minutes 1000 Wall
60 Minutes
Dimensions: 4 3/4" x 21 7/8" x9 W'
18"/Minute Max document thickness 1/32"
12.5"
120V
50/60 Hz
Please Read Before Using!
I ACAUTIONI
• Only use pouches specifically designed for the lamination setting you intend to use.
• Always supervise children during laminator operation.
• Keep pets away from laminator while in use.
• Switch off and unplug laminator when not in use.
• Only open the laminator as explained under "Maintenance". Do not open or attempt
to repair in any other way, as this could result in electric shock and will void your
warranty. Contact Customer Service if you have questions. Please note the warranty
does not apply in cases of abuse, mishandling or unauthorized repair.
• Please be careful of sharp edges and corners and residual heat when opening
the laminator.
To switch the laminator back on, simply press the
stand·by bullon at the left of the front operating
This laminator is equipped with an Auto shut· panel.
During lamination, the direction of the pouch can be
off function. It will turn the laminator into
reversed, if you are unsure about the progress of the
stand·by mode, if it has not been used for
lamination. To do so, press down the reverse key.
over 60 minutes. The LCD screen will show
This will eject the pouch back at the front entry.
the sleep screen when in stand· by.
http://www.monomachines.com
2

http://www.monomachines.com
TIPS
• Always put item in a pouch. Never laminate an empty pouch. • Do not laminate heat-sensitive documents (i.e., tickets, ultrasounds, etc.).
• Trim excess pouch material from around your item after laminating and cooling. • Use a dry-erase marker for writing on laminated pouches.
• Clean laminator rollers with Fellowes roller wipes (item #5703702) after
15-20 applications to guarantee optimum laminating results as explained under
"maintenance".
BEFORE YOU LAMINATE
For best results use
Fellowes® brand pouches.
Position laminator so you
Select correct pouch size for
have enough space to allow
laminated item.
items to pass freely through
the machine.
COLD LAMINATION STEPS
CAUTION: Only use self-adhesive pouches when laminating with a cold setting.
1. Please connect the laminator
to the socket using the separate
power coble supplied.
5. Confirm your selection by
pressing "Enter" bullon in the
middle of navigation keys.
laminator will toke a few minutes
for temperature adjustment.
3. Press Stand-by bullon at left
of front operating panel to switch
laminator on.
4. Use navigation keys to select
selling for cold lamination.
2. Switch laminator on with
Power On / Off bullon at bock
of machine.
6
7. Peel a small port of the protective
sheet away from document.
8. Place pouch, sealed edge first,
6. Centre item on clear side against
into laminator entry. Keep pouch
sealed edge; documents cannot be
straight and use the edge guide
repositioned once laminated.
to centre it. Continue peeling the
protective sheet away.
http://www.monomachines.com
3

http://www.monomachines.com
ENGLISH
HOT LAMINATION STEPS
1. Please connect the laminator
to the socket using the separate
power cable supplied.
2. Switch laminator on with
Power On / Off bullon at back
of machine.
3. Press Stand-by bullon at
left of front operating panel to
switch laminator on.
4. Use navigation keys to select
selling for the hot lamination
pouch thickness (3-10 mil) you
wish to laminate.
8
8. While laminator is warming
up, please prepare item you
wish to laminate. Place the item
inside the pouch and centre it
against the sealed edge of the
pouch. To prevent jamming, use
a carrier when item is smaller
than the pouch.
5. Confirm your selection by
pressing "Enter" bullon in the
middle of navigation keys.
Laminator will take a few minutes
for temperature adjustment.
9
6. During warm-up, a "wait"
symbol will appear in the
LCD screen until the required
temperature has been reached.
7. Once temperature is reached,
acoustic beep signal will sound,
a small arrow will flash in LCD
screen and roller symbols will
rotate.
11
11. Before switching off laminator,
feed empty cleaning/carrier sheet
through machine to clean unit.
9. Place pouch, sealed edge first,
into laminator entry. Keep pouch
straight and use the edge guide
to centre it.
10. To prevent jamming,
immediately remove laminated
item from back of machine. Let
item coolon flat surface for
several seconds.
http://www.monomachines.com
4
I
I

http://www.monomachines.com
I
MAINTENANCE - Unique Easi-Access technology
This laminator is equipped with the unique Easi-Access technology for easy maintenance. This allows the user to open the laminator for maintenance, just like a photocopier.
1. To open the laminator, please press the
"Open" button as shown in the illustration
and wait for the "open" (-t) symbol to
appear on the LCD screen and the ready
beep to sound.
2. If machine is hot, fan will turn on to
cool the machine down to safe handling
temperature inside. During this time the
"Watt" symbol will flash and cover will
remain locked.
3. The "open" symbol will show
in the LCD screen will turn on and
the ready beep will sound when
machine is ready to be opened.
4. Press the buttons on both sides
of the machine to activate the Easi-
Access mechanism. (The laminator
needs to be switched on to allow the
active temperature control to work).
7. To clean residue off laminator
rollers, please only use Fellowes
Laminating Roller cleaners (item
No 5703702) as explained in
product instructions.
8. Please remember to re-secure the
rollers before closing cover to ensure
safe operation.
5. Open the lid with both hands. You are 6. For further maintenance,
now able to clean the inside of the laminator the rollers can be released by
and carefully remove any residual glue or experienced users. Press cam
other items. When laminator is opened, levers to release the rollers.
power to internal parts is isolated, so that
user is not in danger of electric shock.
TROUBLESHOOTING
Problem Solution Cause
Ready Light does not come on after extended time
Laminator is in a hot, humid area.
Move laminator to a cool dry area.
Pouch did not completely adhere to item
Laminated item may be too thick.
Pass through laminator a second time.
Jamming
No item in pouch
Manually cut out pouch used
Pouch was not used.
All our laminators have been designed to operate jam-free. In the
unlikely event of a jam occurring, please press the "open" (-4)
button and wait for the wait (~) light to stop flashing.
The laminator can be opened to remove incorrectly inserted items
Need Help?
Pouch was not centred or straight when fed
through Pouch/Document Entry.
as described under maintenance. Please ensure that you follow the
described steps.
Please call our experts at
Glue and residue left on laminating rollers.
Gently pull on the jammed material to release it.
Customer Service. You'll find
the numbers for your nearest
Service Centre on the
BACK cover of this booklet.
Always put item in a pouch.
Align sealed edge with Pouch/Document Entry. Use guide
on machine to centre.
Clean residues off rollers using Fellowes Laminating Roller wipes,
see "maintenance" section.
Make sure that not residue is left on the rollers and use
cleaning sheet before laminating.
WARRANTY
Fellowes warrants all parts of the laminator to be free of defects in material and workmanship for
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. IN NO EVENT SHALL FELL OW ES BE
2 years from the date of purchase by the original consumer. If any part is found to be defective LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ATIRIBUTABLE TO THIS PRODUCT.
during the warranty period, your sale and exclusive remedy will be repair or replacement, at This warranty gives you specific legal rights. You may have other legal rights that vary from this
Fellowes' option and expense, of the defective part. This warranty does not apply in cases warranty. The duration, terms and conditions of this warranty are valid world-wide, except where
of aruse, mishandling or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF different limitations, restrictions or conditions may be required by local law. For more details or to
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION
obtain services under this warranty, please contact us or your dealer.
s
http://www.monomachines.com

http://www.monomachines.com
Help Line
Austra lia +
1-800-33-11-77
Canada +
1-800-665-4339
Europe
00-800-1810-1810
Fellowes
Austra lia +
61-3-8336-9700
Benelux
+ 31-[0)-76-523-2090
Canada +
1-905-475-6320
Deutschland
+ 49-[0)-5131-49770
Espana +
34-91-748-05-01
France +
33-[0)-1-30-06-86-80
Italia
+ 39-071-730041
Mexico +
1-800-234-1185
United States
+ 1-800-955-0959
Japan
+ 81-[0)-3-5496-2401
Korea +
82-[0)-2-3462-2884
Malaysia
+ 60-[0)-35122-1231
Polska
+ 48-[22)-771-47-40
Singapore
+ 65-6221-3811
United Kingdom
+ 44-[0)-1302-836836
United States
+ 1-630-893-1600
http://www.monomachines.com