Fenix ECOSUN S+ Operation manual

Instructions for use and installation
Radiant electric heating panel: ECOSUN S+
ECOSUN S+ ANTICOR
1. Basic technical data
* version Ecosun S+
2.Use
Radiant panels are intended for the heating of large spaces, mainly industrial halls and workshops, etc., warehouses, shops, function halls
and sports halls. They can also be used for the local heating of designated areas (zonal temperature maintenance).
The Ecosun S+ ANTICOR model is intended for environments with an increased risk of corrosion.
The panel is constructed for use in environments with splashing water. However, rapid cooling of the panel when it is hot can result in
irreversible damage to it.
3. Installation
Installation of these panels may only be carried out by a person with a specialized qualification. The electrical
wiring must comply with the valid norms in the country of installation. The panels can either be hung from the
ceiling on four fixtures using a chain or cords, or with the help of installation brackets. The brackets are
supplied disassembled in the terminal and need to be attached before installation of the panel. The brackets
can be supplemented with a swivel bracket – an inclinable bracket (not part of the product package).
The radiant panel can be installed at an angle as well as vertically. However it must not be installed at an
angle or vertically in such a way that the terminal is the highest part of the panel. There is higher convection
of heat when the panel is in a tilted position and this heat would irreversibly damage the electrical compo-
nents of the terminal.
N529/R02 (02.10.13)
Type Wattage
W
Voltage
V
Protection
class IP Dimensions mm
Weight
kg
ECOSUN S+ 06 * 600 230/400V 3N
IIP 44
650 x 250 x 60
ECOSUN S+ 08 * 850
ECOSUN S+ 09 900 230 V 1N 1550 x 150 x 60 7,8
ECOSUN S+ 12 1200
ECOSUN S+ 18 1800
230/400V 3N
1550 x 250 x 60 12,35
ECOSUN S+ 24 2400
ECOSUN S+ 30 3000 1550 x 350 x 60 16,65
ECOSUN S+ 36 3600
4,9

Installation using a fixing bracket
• Attach the mounting frame so that the opening for the positioning screw is accessible. Slide one side of the panel onto the holder.
• Slide the panel onto the other part of the holder and secure it with a screw.
Typ Spacing Note
ECOSUN S+ 06 100 x 300
− diameter of the opening in the brackets: 6 mm
− when handling the panel, it is not advisable to
touch its radiant surface with dirty hands
ECOSUN S+ 08
ECOSUN S+ 09
ECOSUN S+ 12
ECOSUN S+ 18 100 x 1000
ECOSUN S+ 24
ECOSUN S+ 30 200 x 1000
ECOSUN S+ 36
40 x 1000
Spacing of grips at the back side of the panel:
After insertion, it is advisable to secure it in position with the use of
positioning screws to prevent it from sliding out.
• Clearance distances from flammable objects:
from the radiant surface (temperature up to 380°C): 100 cm
from the top edge at the distance of the mounting brackets
from other parts of the panel: 25 cm
• Lowest height above the floor: 350 cm (recommended value)
• The mutual distance between panels is usually greater than the
height of their installation above the floor
•The panel must not be placed directly under an electric socket.

4. Connection of the panels (see Fig. 1)
The supply cables can be interconnected (looped) directly in the terminals of the panels. A shutoff device, in which the distance be-
tween disconnected contacts is at least 3.5 mm for all poles, must be built into the distribution system. Regulation is provided via room
thermostats with time switching (offered by FENIX) which switch power relays or contactors. For larger buildings, a microprocessor
control system is suitable. In special cases, regulation needs to be considered depending on the situation (zonal temperature mainte-
nance, etc.).
ECOSUN S+ 30-36 panels can be regulated via symmetrical shutoff of the segments (level 1 – central segment, level 2 – both edge
segments, level 3 – all segments switched off).
Any alterations made to the factory connection in the terminal will result in the destruction of the heating lamellas. In order to
comply with the warranty conditions, the customer may only make alterations in the part of the terminal which is used for the
connection of the supply cable.
5. Maintenance
This is limited to cleaning the panel by dusting it or wiping it with a moist cloth and detergent. The radiant surface is not cleaned.
Dust deposits and dampness on the surface of the product lead to the corrosion of components. Remove the dust and dirt, which
absorbs dampness, at least once a year (at least twice a year in environments with higher humidity, mineral substances in the atmos-
phere or excessive dust).
Ecosun S+ 18 - 24; 06 - 08
TRI 400 V
Ecosun S+ 09 - 12
Ecosun S+ 30 - 36
MONO 230 V
MONO 230 V MONO 230 V BI 400 V

6. Warranty conditions
24 months from the date of sale. The warranty does not cover faults caused during transportation, unsuitable storage or unqualified
installation.
You can find the current and full warranty conditions at: www.fenixgroup.eu
7. Warning
When the panel heats up for the first time, the thermal insulation is burnt, which causes a harmless smell (smoke) for a period of max. 60
minutes. Do not touch the heating segments, which are covered by a Silicating layer, in order not to make the radiant surface dirty (if
contact with the segments is necessary, you may use clean textile gloves only). After installation, remove the protective foil which protects
the radiant surface. The ambient temperature (the temperature of the surrounding air) around the ECOSUN radiant panel must not exceed
30°C.
Ecosun S+ panels are not intended for areas where water vapour or dampness containing salt, cleaning agents, etc. occurs, as such
conditions speed up the corrosion of metal parts. Examples of unsuitable locations for installation: in a car wash – including areas with
technical equipment, at water treatment and cleaning plants, by the sea, etc.
This appliance is not intended for use by persons (including children) whose physical, sensory or mental incapacity or lack of experience
would prevent them from using the appliance safely, unless they are supervised or instructed regarding the use of the appliance by a
person who is responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Date of sale:…………………………………………………………………..
Production number:………………………………………………………..
Retailer:………………………………………………………………………